Thermodynamic modeling of hydrogen refueling for heavy-duty fuel cell buses and comparison with aggregated real data

Abstract The foreseen uptake of hydrogen mobility is a fundamental step towards the decarbonization of the transport sector. Under such premises, both refueling infrastructure and vehicles should be deployed together with improved refueling protocols. Several studies focus on refueling the light-duty vehicles with 10 kgH2 up to 700 bar, however less known effort is reported for refueling heavy-duty vehicles with 30–40 kgH2 at 350 bar. The present study illustrates the application of a lumped model to a fuel cell bus tank-to-tank refueling event, tailored upon the real data acquired in the 3Emotion Project. The evolution of the main refueling quantities, such as pressure, temperature, and mass flow, are predicted dynamically throughout the refueling process, as a function of the operating parameters, within the safety limits imposed by SAE J2601/2 technical standard. The results show to refuel the vehicle tank from half to full capacity with an Average Pressure Ramp Rate (APRR) equal to 0.03 MPa/s are needed about 10 min. Furthermore, it is found that the effect of varying the initial vehicle tank pressure is more significant than changing the ambient temperature on the refueling performances. In conclusion, the analysis of the effect of different APRR, from 0.03 to 0.1 MPa/s, indicate that is possible to safely reduce the duration of half-to-full refueling by 62% increasing the APRR value from 0.03 to 0.08 MPa/s

Search for dark matter produced in association with bottom or top quarks in √s = 13 TeV pp collisions with the ATLAS detector

A search for weakly interacting massive particle dark matter produced in association with bottom or top quarks is presented. Final states containing third-generation quarks and miss- ing transverse momentum are considered. The analysis uses 36.1 fb−1 of proton–proton collision data recorded by the ATLAS experiment at √s = 13 TeV in 2015 and 2016. No significant excess of events above the estimated backgrounds is observed. The results are in- terpreted in the framework of simplified models of spin-0 dark-matter mediators. For colour- neutral spin-0 mediators produced in association with top quarks and decaying into a pair of dark-matter particles, mediator masses below 50 GeV are excluded assuming a dark-matter candidate mass of 1 GeV and unitary couplings. For scalar and pseudoscalar mediators produced in association with bottom quarks, the search sets limits on the production cross- section of 300 times the predicted rate for mediators with masses between 10 and 50 GeV and assuming a dark-matter mass of 1 GeV and unitary coupling. Constraints on colour- charged scalar simplified models are also presented. Assuming a dark-matter particle mass of 35 GeV, mediator particles with mass below 1.1 TeV are excluded for couplings yielding a dark-matter relic density consistent with measurements

Mortality and pulmonary complications in patients undergoing surgery with perioperative SARS-CoV-2 infection: an international cohort study

Background: The impact of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) on postoperative recovery needs to be understood to inform clinical decision making during and after the COVID-19 pandemic. This study reports 30-day mortality and pulmonary complication rates in patients with perioperative SARS-CoV-2 infection. Methods: This international, multicentre, cohort study at 235 hospitals in 24 countries included all patients undergoing surgery who had SARS-CoV-2 infection confirmed within 7 days before or 30 days after surgery. The primary outcome measure was 30-day postoperative mortality and was assessed in all enrolled patients. The main secondary outcome measure was pulmonary complications, defined as pneumonia, acute respiratory distress syndrome, or unexpected postoperative ventilation. Findings: This analysis includes 1128 patients who had surgery between Jan 1 and March 31, 2020, of whom 835 (74·0%) had emergency surgery and 280 (24·8%) had elective surgery. SARS-CoV-2 infection was confirmed preoperatively in 294 (26·1%) patients. 30-day mortality was 23·8% (268 of 1128). Pulmonary complications occurred in 577 (51·2%) of 1128 patients; 30-day mortality in these patients was 38·0% (219 of 577), accounting for 81·7% (219 of 268) of all deaths. In adjusted analyses, 30-day mortality was associated with male sex (odds ratio 1·75 [95% CI 1·28–2·40], p\textless0·0001), age 70 years or older versus younger than 70 years (2·30 [1·65–3·22], p\textless0·0001), American Society of Anesthesiologists grades 3–5 versus grades 1–2 (2·35 [1·57–3·53], p\textless0·0001), malignant versus benign or obstetric diagnosis (1·55 [1·01–2·39], p=0·046), emergency versus elective surgery (1·67 [1·06–2·63], p=0·026), and major versus minor surgery (1·52 [1·01–2·31], p=0·047). Interpretation: Postoperative pulmonary complications occur in half of patients with perioperative SARS-CoV-2 infection and are associated with high mortality. Thresholds for surgery during the COVID-19 pandemic should be higher than during normal practice, particularly in men aged 70 years and older. Consideration should be given for postponing non-urgent procedures and promoting non-operative treatment to delay or avoid the need for surgery. Funding: National Institute for Health Research (NIHR), Association of Coloproctology of Great Britain and Ireland, Bowel and Cancer Research, Bowel Disease Research Foundation, Association of Upper Gastrointestinal Surgeons, British Association of Surgical Oncology, British Gynaecological Cancer Society, European Society of Coloproctology, NIHR Academy, Sarcoma UK, Vascular Society for Great Britain and Ireland, and Yorkshire Cancer Research

Impedance-based Solid Oxide Fuel Cell testing as scalable and reliable Quality Control tool for cell and batch manufacturing: first findings

Testing is a necessary step in the manufacturing process of Solid Oxide Fuel Cells (SOFC) to assess the performance of the produced cells before on-field deployment. In this work, the implementation of Electrochemical Impedance Spectroscopy (EIS) and subsequent data elaboration via Equivalent Circuit Modelling (ECM) is evaluated as a viable experimental framework for characterization and Quality Control (QC) of cells or cell batches, complemented to standard polarization-based methods. By performing a statistical analysis of the ECM parameters (representative of each physico-chemical process) the cell and batch operational parameters can be determined and compared. The validity of the proposed methodology is assessed using a wide experimental dataset of a significant number of SOFC samples (20 cells from 3 batches – two of which identical and the third with an intentional modification in the manufacturing process in order to validate the proposed methodology) tested in identical conditions. Results show that the impedance-based method provide detailed information in terms of impedance breakdown (anode gas diffusion process resulting the main criticality), as well as confirming the preliminary results obtained from the polarization approach (Batch#2 showing the lowest total performance and highest uniformity). Highly reproducible intra-batch distributions of the ECM parameters encourage the applicability of such methodology for QC purposes, even with few data collected only in Open Circuit Voltage (OCV) conditions. A relevant deviation of charge transfer and diffusion resistances in Batch#3 respect to other batches is observed (not visible from the polarization curves), which is reconducted to the modified anode functional layer, opening potential applications of the proposed methodology to assess the impact of targeted modifications of manufacturing methods on specific cell electrochemical performances

A System Integration Analysis of a Molten Carbonate Electrolysis Cell as an Off-Gas Recovery System in a Steam-Reforming Process of an Oil Refinery

Technologies capable of efficiently exploiting unavoidable CO2 streams, have to be deeply investigated and deployed during the transition phase to achieve long-term climate neutrality targets. Among the technologies, Molten Carbonate Cells (MCC) Operating in Electrolysis Mode (MCEC) represents a promising facility to valorize CO2-rich waste streams, which are typically available in industrial plants, by their conversion into a high-value H-2/CO syngas. These gaseous products can be reintegrated in a plant or reused in different applications. This study analyzes the integration of a system of the MCEC unit under different operating conditions in terms of composition, current density, and the utilization of fuels in a steam-reforming process of an Italian oil refinery via a mixed experimental-simulative approach. The aim of the current study is to assess the improvement in the overall product yield and further impacts of the MCEC unit on the plant efficiency. The results have shown that it is possible to obtain an electrochemical Specific Energy Consumption for the production of H-2 of 3.24 kWh/NmH23 using the MCEC, whereby the possible integration of a 1-MWe module with a reformer of the proposed plant not only increases the hydrogen yield but also decreases the amount of fuel needed to assist the reforming reaction and separates a CO2 stream after additional purification via an oxy-fuel combustor, consequently determining lower greenhouse gases emissions

A System Integration Analysis of a Molten Carbonate Electrolysis Cell as an Off-Gas Recovery System in a Steam-Reforming Process of an Oil Refinery

Technologies capable of efficiently exploiting unavoidable CO2 streams, have to be deeply investigated and deployed during the transition phase to achieve long-term climate neutrality targets. Among the technologies, Molten Carbonate Cells (MCC) Operating in Electrolysis Mode (MCEC) represents a promising facility to valorize CO2-rich waste streams, which are typically available in industrial plants, by their conversion into a high-value H-2/CO syngas. These gaseous products can be reintegrated in a plant or reused in different applications. This study analyzes the integration of a system of the MCEC unit under different operating conditions in terms of composition, current density, and the utilization of fuels in a steam-reforming process of an Italian oil refinery via a mixed experimental-simulative approach. The aim of the current study is to assess the improvement in the overall product yield and further impacts of the MCEC unit on the plant efficiency. The results have shown that it is possible to obtain an electrochemical Specific Energy Consumption for the production of H-2 of 3.24 kWh/NmH23 using the MCEC, whereby the possible integration of a 1-MWe module with a reformer of the proposed plant not only increases the hydrogen yield but also decreases the amount of fuel needed to assist the reforming reaction and separates a CO2 stream after additional purification via an oxy-fuel combustor, consequently determining lower greenhouse gases emissions

Developing an Automated Tool for Quantitative Analysis of the Deconvoluted Electrochemical Impedance Response of a Solid Oxide Fuel Cell

Despite being commercially available, solid oxide fuel cell (SOFC) technology requires further study to understand its physicochemical processes for diagnostics, prognostics, and quality assurance purposes. Electrochemical impedance spectroscopy (EIS), a widely used characterization technique for SOFCs, is often accompanied by the distribution of relaxation times (DRT) as a method for deconvoluting the contribution of each physicochemical process from the aggregated impedance response spectra. While EIS yields valuable information for the operation of SOFCs, the quantitative analysis of the DRT and its shifts remains cumbersome. To address this issue, and to create a replicable benchmark for the assessment of DRT results, a custom tool was developed in MATLAB to numerically analyze the DRT spectra, identify the DRT peaks, and assess their deviation in terms of peak frequency and DRT amplitude from nominal operating conditions. The preliminary validation of the tool was carried out by applying the tool to an extensive experimental campaign on 23 SOFC button-sized samples from three production batches in which EIS measurements were performed in parametric operating conditions. It was concluded that the results of the automated analysis via the developed tool were in accordance with the qualitative analysis of previous studies. It is capable of providing adequate additional quantitative results in terms of DRT shifts for further analysis and provides the basis for better interoperability of DRT analyses between laboratories

Searches for the ZγZ\gamma decay mode of the Higgs boson and for new high-mass resonances in pppp collisions at s=13\sqrt{s} = 13 TeV with the ATLAS detector

International audienceThis article presents searches for the Zγ decay of the Higgs boson and for narrow high-mass resonances decaying to Zγ, exploiting Z boson decays to pairs of electrons or muons. The data analysis uses 36.1 fb$^{−1}$ of pp collisions at $\sqrt{s}=13$ recorded by the ATLAS detector at the CERN Large Hadron Collider. The data are found to be consistent with the expected Standard Model background. The observed (expected — assuming Standard Model pp → H → Zγ production and decay) upper limit on the production cross section times the branching ratio for pp → H → Zγ is 6.6. (5.2) times the Standard Model prediction at the 95% confidence level for a Higgs boson mass of 125.09 GeV. In addition, upper limits are set on the production cross section times the branching ratio as a function of the mass of a narrow resonance between 250 GeV and 2.4 TeV, assuming spin-0 resonances produced via gluon-gluon fusion, and spin-2 resonances produced via gluon-gluon or quark-antiquark initial states. For high-mass spin-0 resonances, the observed (expected) limits vary between 88 fb (61 fb) and 2.8 fb (2.7 fb) for the mass range from 250 GeV to 2.4 TeV at the 95% confidence level

Search for Scalar Diphoton Resonances in the Mass Range 65−60065-600 GeV with the ATLAS Detector in pppp Collision Data at s\sqrt{s} = 8 TeVTeV

A search for scalar particles decaying via narrow resonances into two photons in the mass range 65–600 GeV is performed using $20.3\text{}\text{}{\mathrm{fb}}^{-1}$ of $\sqrt{s}=8\text{}\text{}\mathrm{TeV}$ $pp$ collision data collected with the ATLAS detector at the Large Hadron Collider. The recently discovered Higgs boson is treated as a background. No significant evidence for an additional signal is observed. The results are presented as limits at the 95% confidence level on the production cross section of a scalar boson times branching ratio into two photons, in a fiducial volume where the reconstruction efficiency is approximately independent of the event topology. The upper limits set extend over a considerably wider mass range than previous searches

Search for direct top squark pair production in final states with two leptons in s=13\sqrt{s} = 13 TeV pppp collisions with the ATLAS detector

International audienceThe results of a search for direct pair production of top squarks in events with two opposite-charge leptons (electrons or muons) are reported, using $36.1~\hbox {fb}^{-1}$ of integrated luminosity from proton–proton collisions at $\sqrt{s}=13$ TeV collected by the ATLAS detector at the Large Hadron Collider. To cover a range of mass differences between the top squark $\tilde{t}$ and lighter supersymmetric particles, four possible decay modes of the top squark are targeted with dedicated selections: the decay $\tilde{t} \rightarrow b \tilde{\chi }_{1}^{\pm }$ into a b-quark and the lightest chargino with $\tilde{\chi }_{1}^{\pm } \rightarrow W \tilde{\chi }_{1}^{0}$ , the decay $\tilde{t} \rightarrow t \tilde{\chi }_{1}^{0}$ into an on-shell top quark and the lightest neutralino, the three-body decay $\tilde{t} \rightarrow b W \tilde{\chi }_{1}^{0}$ and the four-body decay $\tilde{t} \rightarrow b \ell \nu \tilde{\chi }_{1}^{0}$ . No significant excess of events is observed above the Standard Model background for any selection, and limits on top squarks are set as a function of the $\tilde{t}$ and $\tilde{\chi }_{1}^{0}$ masses. The results exclude at 95% confidence level $\tilde{t}$ masses up to about 720 GeV, extending the exclusion region of supersymmetric parameter space covered by previous searches