Static and Dynamic Strain Monitoring of Reinforced Concrete Components through Embedded Carbon Nanotube Cement-Based Sensors

The paper presents a study on the use of cement-based sensors doped with carbon nanotubes as embedded smart sensors for static and dynamic strain monitoring of reinforced concrete (RC) elements. Such novel sensors can be used for the monitoring of civil infrastructures. Because they are fabricated from a structural material and are easy to utilize, these sensors can be integrated into structural elements for monitoring of different types of constructions during their service life. Despite the scientific attention that such sensors have received in recent years, further research is needed to understand (i) the repeatability and accuracy of sensors’ behavior over a meaningful number of sensors, (ii) testing configurations and calibration methods, and (iii) the sensors’ ability to provide static and dynamic strain measurements when actually embedded in RC elements. To address these research needs, this paper presents a preliminary characterization of the self-sensing capabilities and the dynamic properties of a meaningful number of cement-based sensors and studies their application as embedded sensors in a full-scale RC beam. Results from electrical and electromechanical tests conducted on small and full-scale specimens using different electrical measurement methods confirm that smart cement-based sensors show promise for both static and vibration-based structural health monitoring applications of concrete elements but that calibration of each sensor seems to be necessary.Ministerio de Educación FPU13/0489

An Experimental Study on Static and Dynamic Strain Sensitivity of Embeddable Smart Concrete Sensors Doped with Carbon Nanotubes for SHM of Large Structures

The availability of new self-sensing cement-based strain sensors allows the development of dense sensor networks for Structural Health Monitoring (SHM) of reinforced concrete structures. These sensors are fabricated by doping cement-matrix mterials with conductive fillers, such as Multi Walled Carbon Nanotubes (MWCNTs), and can be embedded into structural elements made of reinforced concrete prior to casting. The strain sensing principle is based on the multifunctional composites outputting a measurable change in their electrical properties when subjected to a deformation. Previous work by the authors was devoted to material fabrication, modeling and applications in SHM. In this paper, we investigate the behavior of several sensors fabricated with and without aggregates and with different MWCNT contents. The strain sensitivity of the sensors, in terms of fractional change in electrical resistivity for unit strain, as well as their linearity are investigated through experimental testing under both quasi-static and sine-sweep dynamic uni-axial compressive loadings. Moreover, the responses of the sensors when subjected to destructive compressive tests are evaluated. Overall, the presented results contribute to improving the scientific knowledge on the behavior of smart concrete sensors and to furthering their understanding for SHM applications.Ministerio de Educación FPU13/0489

Dual-readout Calorimetry

The RD52 Project at CERN is a pure instrumentation experiment whose goal is to understand the fundamental limitations to hadronic energy resolution, and other aspects of energy measurement, in high energy calorimeters. We have found that dual-readout calorimetry provides heretofore unprecedented information event-by-event for energy resolution, linearity of response, ease and robustness of calibration, fidelity of data, and particle identification, including energy lost to binding energy in nuclear break-up. We believe that hadronic energy resolutions of {\sigma}/E $\approx$ 1 - 2% are within reach for dual-readout calorimeters, enabling for the first time comparable measurement preci- sions on electrons, photons, muons, and quarks (jets). We briefly describe our current progress and near-term future plans. Complete information on all aspects of our work is available at the RD52 website http://highenergy.phys.ttu.edu/dream/.Comment: 10 pages, 10 figures, Snowmass White pape

Cross-sectional association of volume, blood pressures, and aortic stiffness with left ventricular mass in incident hemodialysis patients: the Predictors of Arrhythmic and Cardiovascular Risk in End-Stage Renal Disease (PACE) study

BACKGROUND: Higher left ventricular mass (LV) strongly predicts cardiovascular mortality in hemodialysis patients. Although several parameters of preload and afterload have been associated with higher LV mass, whether these parameters independently predict LV mass, remains unclear. METHODS: This study examined a cohort of 391 adults with incident hemodialysis enrolled in the Predictors of Arrhythmic and Cardiovascular Risk in End Stage Renal Disease (PACE) study. The main exposures were systolic and diastolic blood pressure (BP), pulse pressure, arterial stiffness by pulse wave velocity (PWV), volume status estimated by pulmonary pressures using echocardiogram and intradialytic weight gain. The primary outcome was baseline left ventricular mass index (LVMI). RESULTS: Each systolic, diastolic blood, and pulse pressure measurement was significantly associated with LVMI by linear regression regardless of dialysis unit BP or non-dialysis day BP measurements. Adjusting for cardiovascular confounders, every 10 mmHg increase in systolic or diastolic BP was significantly associated with higher LVMI (SBP β = 7.26, 95 % CI: 4.30, 10.23; DBP β = 10.05, 95 % CI: 5.06, 15.04), and increased pulse pressure was also associated with higher LVMI (β = 0.71, 95 % CI: 0.29, 1.13). Intradialytic weight gain was also associated with higher LVMI but attenuated effects after adjustment (β = 3.25, 95 % CI: 0.67, 5.83). PWV and pulmonary pressures were not associated with LVMI after multivariable adjustment (β = 0.19, 95 % CI: −1.14, 1.79; and β = 0.10, 95 % CI: −0.51, 0.70, respectively). Simultaneously adjusting for all main exposures demonstrated that higher BP was independently associated with higher LVMI (SBP β = 5.64, 95 % CI: 2.78, 8.49; DBP β = 7.29, 95 % CI: 2.26, 12.31, for every 10 mmHg increase in BP). CONCLUSIONS: Among a younger and incident hemodialysis population, higher systolic, diastolic, or pulse pressure, regardless of timing with dialysis, is most associated with higher LV mass. Future studies should consider the use of various BP measures in examining the impact of BP on LVM and cardiovascular disease. Findings from such studies could suggest that high BP should be more aggressively treated to promote LVH regression in incident hemodialysis patients. ELECTRONIC SUPPLEMENTARY MATERIAL: The online version of this article (doi:10.1186/s12882-015-0131-4) contains supplementary material, which is available to authorized users

Caracterización física y química de ríos de montaña (Tafí del Valle-Tucumán-Argentina)

En este trabajo se estudió durante el ciclo anual 2000-2001, a los ríos Blanquito, Churqui, de La Ovejería, de Las Carreras, Tafí, El Mollar y Los Sosa, ubicados a 2000 msnm en el valle de Tafí (Tucumán-Argentina). El objetivo de esta contribución fue caracterizar e interpretar las variaciones espacio-temporales de los parámetros físicos y químicos en relación con la dinámica hidrológica a la que se encuentran sujetos estos ecosistemas acuáticos y además, comparar la calidad de sus aguas. Las variables físicas y químicas analizadas fueron: oxígeno disuelto (OD), demanda bioquímica de oxígeno (DBO5), iones mayoritarios, compuestos nitrogenados, ortofosfatos y metales pesados. Los resultados muestran que la temperatura varió entre 4.2 y 28 ◦C, el pH fluctuó de neutro a alcalino (6.7-8.7) y la conductividad eléctrica entre 64 y 296 μS/cm. El OD y la DBO5 se mostraron estables, alcanzando máximos valores de 10.1 y 2 mg/l, respectivamente. El agua pudo caracterizarse como bicarbonatada-cálcica dominante. Las concentraciones de N-NO−3 oscilaron entre 0.1 y 0.6 mg/l, el N-NO−2 sólo llegó en el río Churqui a 0.01 mg/l y el N-NH+4 alcanzó valores de 0.8 mg/l. En general los registros de los ortofosfatos fueron inferiores a 0.2 mg/l. Los metales pesados Cu2+ y Fe3+ llegaron a un máximo de 3 mg/l y 1.8 mg/l, respectivamente. Las mayores concentraciones del hierro se presentaron en el río de La Ovejería y de cobre en el río El Mollar, probablemente por contaminación antropogénica. La interpretación de los análisis de componentes principales realizados sobre la matriz de parámetros físicos y químicos, permitió diferenciar a los sistemas lóticos temporal y espacialmente. El componente 1 ordenó a los ríos de acuerdo a los iones mayoritarios predominantes y a la conductividad, lo que podría interpretarse como un eje de mineralización. Los componentes 2 y 3, ordenaron las muestras de invierno y primavera y las de verano y otoño, de acuerdo a la variación cíclica estacional coincidiendo con las condiciones climáticas del área de estudio.In this work, throughout the 2000-2001 annual period, the Blanquito, Churqui, de La Ovejería, de Las Carreras, Tafí, El Mollar and Los Sosa rivers, located at 2000 m above sea level in the Taf'ı Valley (Tucumán-Argentina) were studied. The aim of this paper was not only to characterize and understand the spatial and temporal variations of physical and chemical parameters related to the hydrological dynamics these aquatic ecosystems are subject to, but also to compare the quality of their waters. Physical and chemical variables analysed were: dissolved oxygen (DO), biochemical oxygen demand (BOD5), preponderant ions, nitrogenous compounds, orthophosphates, and heavy metals. Results show that the temperature ranged between 4.2 and 28 ◦C, pH fluctuated from neutral to alkaline (6.7-8.7) and electrical conductivity varied between 64 and 296 μS/cm. DO and BOD5 were stable and reached maximum values of 10.1 and 2 mg/l, respectively. The water could be characterized as mainly bicarbonated-calcic. N-NO−3 concentrations ranged between 0.1 and 0.6 mg/l, N-NO−2 reaching only 0.01 mg/l in the Churqui river, and N-NH+4 reached values of 0.8 mg/l. In general, orthophosphate records were lower than 0.2 mg/l. Maximum values for heavy metals, Cu2 + and Fe3 + were 3 mg/l y 1.8 mg/l, respectively. Iron highest concentrations were found in de La Ovejería river, whereas those for copper were found in El Mollar river, probably due to anthropogenic pollution. The interpretation of the main component analyses carried out on the physical and chemical parameters matrix, allowed to differentiate lotic systems both temporally and spatially. Component 1 ordered the rivers according to both the prevailing ions and conductivity, which could be interpreted as a mineralization axis. Components 2 and 3 ordered the winter and spring, and the summer and autumn samples according to the seasonal cyclic variation, coinciding with the climatic conditions of the area under study

Hadron detection with a dual-readout fiber calorimeter

In this paper, we describe measurements of the response functions of a fiber-based dual- readout calorimeter for pions, protons and multiparticle "jets" with energies in the range from 10 to 180 GeV. The calorimeter uses lead as absorber material and has a total mass of 1350 kg. It is complemented by leakage counters made of scintillating plastic, with a total mass of 500 kg. The effects of these leakage counters on the calorimeter performance are studied as well. In a separate section, we investigate and compare different methods to measure the energy resolution of a calorimeter. Using only the signals provided by the calorimeter, we demonstrate that our dual-readout calorimeter, calibrated with electrons, is able to reconstruct the energy of proton and pion beam particles to within a few percent at all energies. The fractional widths of the signal distributions for these particles (sigma/E) scale with the beam energy as 30%/sqrt(E), without any additional contributing terms

Lean and performance: an assessment on North-East Italy

ope

Observation of associated near-side and away-side long-range correlations in √sNN=5.02 TeV proton-lead collisions with the ATLAS detector

Two-particle correlations in relative azimuthal angle (Δϕ) and pseudorapidity (Δη) are measured in √sNN=5.02  TeV p+Pb collisions using the ATLAS detector at the LHC. The measurements are performed using approximately 1  μb-1 of data as a function of transverse momentum (pT) and the transverse energy (ΣETPb) summed over 3.1<η<4.9 in the direction of the Pb beam. The correlation function, constructed from charged particles, exhibits a long-range (2<|Δη|<5) “near-side” (Δϕ∼0) correlation that grows rapidly with increasing ΣETPb. A long-range “away-side” (Δϕ∼π) correlation, obtained by subtracting the expected contributions from recoiling dijets and other sources estimated using events with small ΣETPb, is found to match the near-side correlation in magnitude, shape (in Δη and Δϕ) and ΣETPb dependence. The resultant Δϕ correlation is approximately symmetric about π/2, and is consistent with a dominant cos⁡2Δϕ modulation for all ΣETPb ranges and particle pT

Single hadron response measurement and calorimeter jet energy scale uncertainty with the ATLAS detector at the LHC

The uncertainty on the calorimeter energy response to jets of particles is derived for the ATLAS experiment at the Large Hadron Collider (LHC). First, the calorimeter response to single isolated charged hadrons is measured and compared to the Monte Carlo simulation using proton-proton collisions at centre-of-mass energies of sqrt(s) = 900 GeV and 7 TeV collected during 2009 and 2010. Then, using the decay of K_s and Lambda particles, the calorimeter response to specific types of particles (positively and negatively charged pions, protons, and anti-protons) is measured and compared to the Monte Carlo predictions. Finally, the jet energy scale uncertainty is determined by propagating the response uncertainty for single charged and neutral particles to jets. The response uncertainty is 2-5% for central isolated hadrons and 1-3% for the final calorimeter jet energy scale.Comment: 24 pages plus author list (36 pages total), 23 figures, 1 table, submitted to European Physical Journal

Search for squarks and gluinos in events with isolated leptons, jets and missing transverse momentum at s√=8 TeV with the ATLAS detector

The results of a search for supersymmetry in final states containing at least one isolated lepton (electron or muon), jets and large missing transverse momentum with the ATLAS detector at the Large Hadron Collider are reported. The search is based on proton-proton collision data at a centre-of-mass energy s√=8 TeV collected in 2012, corresponding to an integrated luminosity of 20 fb−1. No significant excess above the Standard Model expectation is observed. Limits are set on supersymmetric particle masses for various supersymmetric models. Depending on the model, the search excludes gluino masses up to 1.32 TeV and squark masses up to 840 GeV. Limits are also set on the parameters of a minimal universal extra dimension model, excluding a compactification radius of 1/R c = 950 GeV for a cut-off scale times radius (ΛR c) of approximately 30