Upgrading biogas with novel composite carbon molecular sieve (CCMS) membranes: Experimental and techno-economic assessment

The use of biogas as feedstock for hydrogen production was widely proposed in the literature in the last years as a strategy to reduce anthropogenic carbon emissions. However, its lower heating value compared to natural gas hampers the revamping of existing reforming plants. The use of composite carbon molecular sieve membranes for biogas upgrading (CO2 removal from biogas) was investigated experimentally in this work. In particular, ideal perm-selectivities and permeabilities above the Robeson plot for CO2/CH4 mixtures have been obtained. These membranes show better performances compared to polymeric membranes, which are nowadays commercialized for CO2 separation in natural gas streams. Compared to polymeric membranes, carbon membranes do not show deactivation by plasticization when exposed to CO2, and thus can find industrial application. This work was extended with a techno-economic analysis where carbon membranes are installed in a steam methane reforming plant. Results have been first validated with data from literature and show that the use of biogas increases the costs of hydrogen production to a value of 0.25 €/Nm3 compared to the benchmark technology (0.21 €/Nm3). On the other hand, the use of biogas leads to a decrease in carbon emissions up to 95%, thus the use of biogas for hydrogen production is foreseen as a very interesting alternative to conventional technologies in view of the reduction in the carbon footprint in the novel technologies that are to be installed in the near future

New hydrophilic carbon molecular sieve membranes for bioethanol dehydration via pervaporation

Tubular supported carbon molecular sieve membranes (CMSMs) with high hydrophilicity and perm-selectivities for water suitable for ethanol dehydration were developed from a Novolac oligomer phenolic resin as precursor. Alpha alumina supported CMSMs resulted in 1.69 times higher surface roughness than zirconia supports. The higher surface roughness resulted in 48% higher selective layer thickness. According to pervaporation results, water permeance decreased by the increase in selective layer thickness and mole based selectivity of water- ethanol was enhanced. The oligomer with 3982 g/mol molecular weight enabled membrane to reach high selectivity with one-layer coating. Performance of the membranes are compared with literature data in terms of mole-based selectivity vs. water permeance. CMSMs could be a potential substitution for traditional ethanol dehydration methods with offering higher performance and as a result reducing the final price of bioethanol to be used as a sustainable energy source.The research has been carried out within the TTW Perspectief Pro-gramme “Microsync” project number P16-1

Effect of aluminium acetyl acetonate on the hydrogen and nitrogen permeation of carbon molecular sieves membranes

With a growing interest in hydrogen as energy carrier, the efficient purification of hydrogen from gaseous mixtures is very important. This paper addresses the separation of hydrogen using Carbon Molecular Sieves Membranes (CMSM), which show an attractive combination of high permeability, selectivity and stability. Supported CMSM containing various amounts of aluminium have been prepared from novolac and aluminium acetyl acetonate (Al(acac)3) as carbon and alumina precursors. The thickness of the CMSM layers depend on the content of Al(acac)3 in the dipping solution, which also has influence in the pore size and pore size distribution of the membranes. The permeation properties of the membranes against the Al content in the membrane follows a volcano shape, where the membrane containing 4 wt (%) of Al(acac)3 has the best properties and was stable during 720 h for hydrogen at 150 °C and 6 bar pressure difference. All the CMSM have permeation properties well above the Robeson Upper limit.The research has been carried out within the TTW Perspectief Programme “Microsync” project number P16-10

Effect of Au addition on hydrogen permeation and the resistance to H2S on Pd-Ag alloy membranes

In order to make a detailed comparison between Pd-Ag and Pd-Ag-Au membranes according to their H2 permeation properties and sulfide resistance Au was deposited by the electroless plating (ELP) technique onto one half of Pd-Ag membranes. Membranes' thicknesses are ranged between 2.45 and 3.13 µm. Permeation tests have been carried out from 400 to 600 °C under single gas conditions. The Pd91.7Ag4.8Au3.5 membrane has shown a H2 permeance of 4.71·10−3 mol s−1 m−2 Pa0.5 at 600 °C, which is one of the highest values ever reported in the literature, where the Pd-Ag-Au membranes have exhibited higher hydrogen permeation rates compared to their respective Pd-Ag membranes above 550 °C. The H2 permeation properties have been determined in terms of the degree of H2S inhibition, up to 17 ppm, and subsequent H2 flux recovery rate. Pd-Ag membranes alloyed with gold resisted 12.5 h of H2S exposure showing recovery rates of 85% and 83% for Pd91.5Ag4.7Au3.8 and Pd90.5Ag4.6Au4.9 membranes, respectively, whereas the hydrogen flux of non-gold membranes decreased below detectable values. H2/N2 ideal perm-selectivity of the Pd-Ag membrane was reduced to 18 after H2S tests (starting from > 1308) while Pd-Ag-Au membranes showed a better resistance to sulfur with H2/N2 selectivity values of 793 and 121 (starting from > 4115 and > 2557 respectively). No evidence of the formation of a crystalline sulfide phase on the Pd-Ag-Au alloy membrane surfaces was found in the XRD patterns after H2S exposure and also XPS characterization did not show important changes in the composition before and after the H2S exposure tests. However, SEM images showed a decrease in the thickness of the Pd-Ag membrane and signs of corrosion and roughening on its surface, while gold-alloyed membranes did not show any damage. Keywords Palladium-silver-gold membrane; Electroless plating; H2 permeation; H2S poisoning; H2 recover

Effect of Au addition on hydrogen permeation and the resistance to H2S on Pd-Ag alloy membranes

In order to make a detailed comparison between Pd-Ag and Pd-Ag-Au membranes according to their H2 permeation properties and sulfide resistance Au was deposited by the electroless plating (ELP) technique onto one half of Pd-Ag membranes. Membranes' thicknesses are ranged between 2.45 and 3.13 µm. Permeation tests have been carried out from 400 to 600 °C under single gas conditions. The Pd91.7Ag4.8Au3.5 membrane has shown a H2 permeance of 4.71·10−3 mol s−1 m−2 Pa0.5 at 600 °C, which is one of the highest values ever reported in the literature, where the Pd-Ag-Au membranes have exhibited higher hydrogen permeation rates compared to their respective Pd-Ag membranes above 550 °C. The H2 permeation properties have been determined in terms of the degree of H2S inhibition, up to 17 ppm, and subsequent H2 flux recovery rate. Pd-Ag membranes alloyed with gold resisted 12.5 h of H2S exposure showing recovery rates of 85% and 83% for Pd91.5Ag4.7Au3.8 and Pd90.5Ag4.6Au4.9 membranes, respectively, whereas the hydrogen flux of non-gold membranes decreased below detectable values. H2/N2 ideal perm-selectivity of the Pd-Ag membrane was reduced to 18 after H2S tests (starting from > 1308) while Pd-Ag-Au membranes showed a better resistance to sulfur with H2/N2 selectivity values of 793 and 121 (starting from > 4115 and > 2557 respectively). No evidence of the formation of a crystalline sulfide phase on the Pd-Ag-Au alloy membrane surfaces was found in the XRD patterns after H2S exposure and also XPS characterization did not show important changes in the composition before and after the H2S exposure tests. However, SEM images showed a decrease in the thickness of the Pd-Ag membrane and signs of corrosion and roughening on its surface, while gold-alloyed membranes did not show any damage. Keywords Palladium-silver-gold membrane; Electroless plating; H2 permeation; H2S poisoning; H2 recover

Measurement of the polarisation of W bosons produced with large transverse momentum in pp collisions at sqrt(s) = 7 TeV with the ATLAS experiment

This paper describes an analysis of the angular distribution of W->enu and W->munu decays, using data from pp collisions at sqrt(s) = 7 TeV recorded with the ATLAS detector at the LHC in 2010, corresponding to an integrated luminosity of about 35 pb^-1. Using the decay lepton transverse momentum and the missing transverse energy, the W decay angular distribution projected onto the transverse plane is obtained and analysed in terms of helicity fractions f0, fL and fR over two ranges of W transverse momentum (ptw): 35 < ptw < 50 GeV and ptw > 50 GeV. Good agreement is found with theoretical predictions. For ptw > 50 GeV, the values of f0 and fL-fR, averaged over charge and lepton flavour, are measured to be : f0 = 0.127 +/- 0.030 +/- 0.108 and fL-fR = 0.252 +/- 0.017 +/- 0.030, where the first uncertainties are statistical, and the second include all systematic effects.Comment: 19 pages plus author list (34 pages total), 9 figures, 11 tables, revised author list, matches European Journal of Physics C versio

Observation of a new chi_b state in radiative transitions to Upsilon(1S) and Upsilon(2S) at ATLAS

The chi_b(nP) quarkonium states are produced in proton-proton collisions at the Large Hadron Collider (LHC) at sqrt(s) = 7 TeV and recorded by the ATLAS detector. Using a data sample corresponding to an integrated luminosity of 4.4 fb^-1, these states are reconstructed through their radiative decays to Upsilon(1S,2S) with Upsilon->mu+mu-. In addition to the mass peaks corresponding to the decay modes chi_b(1P,2P)->Upsilon(1S)gamma, a new structure centered at a mass of 10.530+/-0.005 (stat.)+/-0.009 (syst.) GeV is also observed, in both the Upsilon(1S)gamma and Upsilon(2S)gamma decay modes. This is interpreted as the chi_b(3P) system.Comment: 5 pages plus author list (18 pages total), 2 figures, 1 table, corrected author list, matches final version in Physical Review Letter

Search for displaced vertices arising from decays of new heavy particles in 7 TeV pp collisions at ATLAS

We present the results of a search for new, heavy particles that decay at a significant distance from their production point into a final state containing charged hadrons in association with a high-momentum muon. The search is conducted in a pp-collision data sample with a center-of-mass energy of 7 TeV and an integrated luminosity of 33 pb^-1 collected in 2010 by the ATLAS detector operating at the Large Hadron Collider. Production of such particles is expected in various scenarios of physics beyond the standard model. We observe no signal and place limits on the production cross-section of supersymmetric particles in an R-parity-violating scenario as a function of the neutralino lifetime. Limits are presented for different squark and neutralino masses, enabling extension of the limits to a variety of other models.Comment: 8 pages plus author list (20 pages total), 8 figures, 1 table, final version to appear in Physics Letters

Measurement of the inclusive isolated prompt photon cross-section in pp collisions at sqrt(s)= 7 TeV using 35 pb-1 of ATLAS data

A measurement of the differential cross-section for the inclusive production of isolated prompt photons in pp collisions at a center-of-mass energy sqrt(s) = 7 TeV is presented. The measurement covers the pseudorapidity ranges |eta|<1.37 and 1.52<=|eta|<2.37 in the transverse energy range 45<=E_T<400GeV. The results are based on an integrated luminosity of 35 pb-1, collected with the ATLAS detector at the LHC. The yields of the signal photons are measured using a data-driven technique, based on the observed distribution of the hadronic energy in a narrow cone around the photon candidate and the photon selection criteria. The results are compared with next-to-leading order perturbative QCD calculations and found to be in good agreement over four orders of magnitude in cross-section.Comment: 7 pages plus author list (18 pages total), 2 figures, 4 tables, final version published in Physics Letters

Search for direct production of charginos and neutralinos in events with three leptons and missing transverse momentum in √s = 7 TeV pp collisions with the ATLAS detector

A search for the direct production of charginos and neutralinos in final states with three electrons or muons and missing transverse momentum is presented. The analysis is based on 4.7 fb−1 of proton–proton collision data delivered by the Large Hadron Collider and recorded with the ATLAS detector. Observations are consistent with Standard Model expectations in three signal regions that are either depleted or enriched in Z-boson decays. Upper limits at 95% confidence level are set in R-parity conserving phenomenological minimal supersymmetric models and in simplified models, significantly extending previous results