Synthesis of zinc oxide/silica composite nanoparticles by flame spray pyrolysis

Zinc oxide (ZnO)/silica (SiO2) composite nanoparticles were made by flame spray pyrolysis. The effects of the Zn/Si ratio on particle properties were examined and compared with those of the pure ZnO and SiO2 particles made at the same conditions. Polyhedral aggregates of nano-sized primary particles were obtained in all experiments. The mixed-oxide primary particle size was smaller than that of pure oxides. The primary particles consisted of ZnO nano-crystals and amorphous SiO2, as seen by high-resolution transmission electron microscopy (HR-TEM) and X-ray diffraction (XRD) analysis using the fundamental parameter approach. The XRD size of ZnO was controlled from 1.2 to 11.3 nm by the initial precursor composition and it was consistent with HR-TEM. The composite particles exhibited an excellent thermal stability and little crystalline growth of ZnO (e.g., from 1.9 to 2.2 nm) was observed even after calcination at 600°

Flame-made Ceria Nanoparticles

Flame spray pyrolysis (FSP) has been used to synthesize high-surface-area ceria from cerium acetate in acetic acid solution. With the addition of an iso-octane/2-butanol mixture to that solution, homogeneous CeO2 nanoparticles were obtained. The specific surface area of the powders ranged from 240 to 101 m2/g by controlling the oxygen dispersion and liquid precursor flow rates through the flame. Furthermore, for production rates from 2 to 10 g/h a constant average primary particle size could be obtained at selected process parameters. The ceria showed high crystallinity and primary particles with a stepped surface. The powder exhibited good thermal stability and conserved up to 40% of its initial specific surface area when calcinated for 2 h at 900 °C. This shows the potential of FSP made ceria for high-temperature applications as in three-way catalysts or fuel cell

Simultaneous deposition of Au nanoparticles during flame synthesis of TiO2 and SiO2

Nanostructured gold/titania and gold/silica particles with up to 4 wt% Au were made by a single-step process in a spray flame reactor. Gold(III)-chloride hydrate and titania- or silica-based metalorganic precursors were mixed in a liquid fuel solution, keeping concentrations in the flame and overall combustion enthalpy constant. The powders were characterized by x-ray diffraction, transmission electron microscopy, Brunauer-Emmett-Teller, and ultraviolet-visible analysis. The titania or silica specific surface area and the crystalline structure of titania were not affected by the presence of gold in the flame. Furthermore the size of the gold deposits was independent of the metal oxide support (TiO2 or SiO2) and its specific surface area (100 and 320 m2/g, respectively). The gold nanoparticles were nonagglomerated, spherical, mostly single crystalline, and well dispersed on the metal oxide support. Depending on the Au weight fraction (1, 2, and 4 wt%) the Au nanoparticles' mass mean diameter was 3, 7, and 15 nm, respectively, on both titania and silica. The particles showed surface plasmon absorption bands in the ultraviolet-visible region, which is typical for nano-sized gold. This absorption band was red shifted in the case of the titania support, while no shift occurred with the silica suppor

Adhesion mechanisms of the contact interface of TiO2 nanoparticles in films and aggregates

Fundamental knowledge about the mechanisms of adhesion between oxide particles with diameters of few nanometers is impeded by the difficulties associated with direct measurements of contact forces at such a small size scale. Here we develop a strategy based on AFM force spectroscopy combined with all-atom molecular dynamics simulations to quantify and explain the nature of the contact forces between 10 nm small TiO2 nanoparticles. The method is based on the statistical analysis of the force peaks measured in repeated approaching/retracting loops of an AFM cantilever into a film of nanoparticle agglomerates and relies on the in-situ imaging of the film stretching behavior in an AFM/TEM setup. Sliding and rolling events first lead to local rearrangements in the film structure when subjected to tensile load, prior to its final rupture caused by the reversible detaching of individual nanoparticles. The associated contact force of about 2.5 nN is in quantitative agreement with the results of molecular dynamics simulations of the particle–particle detachment. We reveal that the contact forces are dominated by the structure of water layers adsorbed on the particles’ surfaces at ambient conditions. This leads to nonmonotonous force–displacement curves that can be explained only in part by classical capillary effects and highlights the importance of considering explicitly the molecular nature of the adsorbates

Sensing low concentrations of CO using flame-spray-made Pt/SnO2 nanoparticles

Tin dioxide nanoparticles of different sizes and platinum doping contents were synthesized in one step using the flame spray pyrolysis (FSP) technique. The particles were used to fabricate semiconducting gas sensors for low level CO detection, i.e. with a CO gas concentration as low as 5ppm in the absence and presence of water. Post treatment of the SnO2 nanoparticles was not needed enabling the investigation of the metal oxide particle size effect. Gas sensors based on tin dioxide with a primary particle size of 10nm showed signals one order of magnitude higher than the ones corresponding to the primary particle size of 330nm. In situ platinum functionalization of the SnO2 during FSP synthesis resulted in higher sensor responses for the 0.2wt% Pt-content than for the 2.0wt% Pt. The effect is mainly attributed to catalytic consumption of CO and to the associated reduced sensor response. Pure and functionalized tin dioxide nanoparticles have been characterized by Brunauer, Emmett and Teller (BET) surface area determination, X-ray diffraction (XRD), high resolution transmission electron microscopy (HRTEM) and scanning transmission electron microscopy (STEM) while the platinum oxidation state and dispersion have been investigated by X-ray photoelectron spectroscopy (XPS) and extended X-ray absorption fine structure (EXAFS). The sensors showed high stability (up to 20days) and are suitable for low level CO detection: <10ppm according to European and 50ppm according to US legislation, respectivel

Surface functionalization of biomedical Ti-6Al-7Nb alloy by liquid metal dealloying

Surface functionalization is an effective approach to change the surface properties of a material to achieve a specific goal such as improving the biocompatibility of the material. Here, the surface of the commercial biomedical Ti-6Al-7Nb alloy was functionalized through synthesizing of a porous surface layer by liquid metal dealloying (LMD). During LMD, the Ti-6Al-7Nb alloy is immersed in liquid magnesium (Mg) and both materials react with each other. Particularly, aluminum (Al) is selectively dissolved from the Ti-6Al-7Nb alloy into liquid Mg while titanium (Ti) and niobium (Nb) diffuse along the metal/liquid interface to form a porous structure. We demonstrate that the porous surface layer in the Ti-6Al-7Nb alloy can be successfully tailored by LMD. Furthermore, the concentration of harmful Al in this porous layer is reduced by about 48% (from 5.62 ± 0.11 wt.% to 2.95 ± 0.05 wt.%) after 30 min of dealloying at 1150 K. The properties of the porous layer (e.g., layer thickness) can be tuned by varying the dealloying conditions. In-vitro tests suggest improved bone formation on the functionalized porous surface of the Ti-6Al-7Nb alloy. © 2020 by the authors. Licensee MDPI, Basel, Switzerland.European Research Council, ERCTohoku UniversityMinistry of Science and Higher Education of the Russian FederationNanjing University of Science and Technology, NUST: K2-2020-020MA 3333/13-1Supervision, I.V.O., R.W.-R., L.Z., L.M., J.E. and H.K.; Validation, I.V.O., S.-H.J., and B.L.; Writing – original draft, I.V.O. and B.L.; Writing – review & editing, all. All authors have read and agreed to the published version Funding: The financial support was provided by the German Science Foundation under the Leibniz Program of the manuscript. (Grant MA 3333/13-1), by the European Research Council (ERC) under the ERC Advanced Grant INTELHYB (grant Funding: The financial support was provided by the German Science Foundation under the Leibniz Program Ministry of Science and Higher Education of the Russian Federation, in the framework of the Increase Competitiveness (Grant MA 3333/13-1), by the European Research Council (ERC) under the ERC Advanced Grant INTELHYB Program of NUST «MISiS» (grant number K2-2020-020). I.V.O. is grateful for the financial support provided by the International Collaboration Center, Institute for Materials Research (ICC-IMR), Tohoku University, Japan. 02.A03.21.0006), and the Ministry of Science and Higher Education of the Russian Federation, in the framework Conflicts of Interest: The authors declare no conflict of interest. of the Increase Competitiveness Program of NUST «MISiS» (grant number K2-2020-020). I.V.O. is grateful for the financial support provided by the International Collaboration Center, Institute for Materials Research (ICC-IMR), Tohoku University, Japan

Additive manufacturing of heavy rare earth free high-coercivity permanent magnets

Laser based powder bed fusion is a promising manufacturing method that can be used for the fabrication of hard magnets such as NdFeB with nearly any given geometrical shape. However, the weak performance, e.g., low coercivity, of the 3D-printed magnets currently hinder their application. In this work, we demonstrated a proof-of-concept of powder bed additive manufacturing of heavy rare earth free NdFeB magnets with technologically attractive coercivity values. The 3D-printed NdFeB magnets exhibit the highest (up-to-date for the additively manufactured magnets without heavy rare earth metals) coercivity values reaching μ0Hc = 1.6 T. The magnets were synthesized using a mixture of the NdFeB-based and the low-melting eutectic alloy powders. The essential function of the eutectic alloy, along with binding of the NdFeB-based magnetic particles, is the significant improvement of their coercivity by the in-situ grain boundary (GB) infiltration. The fundamental understanding of the magnetization reversal processes in these 3D-printed magnets leads to the conclusion that the excellent performance of the additively manufactured hard magnets can be achieved through the delicate control of the intergrain exchange interaction between the grains of the Nd2Fe14B phase. © 2020 Acta Materialia Inc.Government Council on Grants, Russian FederationMinistry of Science and Higher Education of the Russian Federation: FEUZ-2020-0051MA 3333/13-1The financial support was provided by the German Science Foundation under the Leibniz Program (Grant MA 3333/13-1), by Act 211 Government of the Russian Federation (contract № 02.A03.21.0006), and Ministry of Science and Higher Education of the Russian Federation, Grant Number FEUZ-2020-0051

Age-related microstructural differences quantified using myelin water imaging and advanced diffusion MRI

Age-related microstructural differences have been detected using diffusion tensor imaging (DTI). Although DTI is sensitive to the effects of aging, it is not specific to any underlying biological mechanism, including demyelination. Combining multiexponential T2 relaxation (MET2) and multishell diffusion MRI (dMRI) techniques may elucidate such processes. Multishell dMRI and MET2 data were acquired from 59 healthy participants aged 17-70 years. Whole-brain and regional age-associated correlations of measures related to multiple dMRI models (DTI, diffusion kurtosis imaging [DKI], neurite orientation dispersion and density imaging [NODDI]) and myelin-sensitive MET2 metrics were assessed. DTI and NODDI revealed widespread increases in isotropic diffusivity with increasing age. In frontal white matter, fractional anisotropy linearly decreased with age, paralleled by increased "neurite" dispersion and no difference in myelin water fraction. DKI measures and neurite density correlated well with myelin water fraction and intracellular and extracellular water fraction. DTI estimates remain among the most sensitive markers for age-related alterations in white matter. NODDI, DKI, and MET2 indicate that the initial decrease in frontal fractional anisotropy may be due to increased axonal dispersion rather than demyelination

<i>Gaia</i> Data Release 1. Summary of the astrometric, photometric, and survey properties

Context. At about 1000 days after the launch of Gaia we present the first Gaia data release, Gaia DR1, consisting of astrometry and photometry for over 1 billion sources brighter than magnitude 20.7. Aims. A summary of Gaia DR1 is presented along with illustrations of the scientific quality of the data, followed by a discussion of the limitations due to the preliminary nature of this release. Methods. The raw data collected by Gaia during the first 14 months of the mission have been processed by the Gaia Data Processing and Analysis Consortium (DPAC) and turned into an astrometric and photometric catalogue. Results. Gaia DR1 consists of three components: a primary astrometric data set which contains the positions, parallaxes, and mean proper motions for about 2 million of the brightest stars in common with the HIPPARCOS and Tycho-2 catalogues – a realisation of the Tycho-Gaia Astrometric Solution (TGAS) – and a secondary astrometric data set containing the positions for an additional 1.1 billion sources. The second component is the photometric data set, consisting of mean G-band magnitudes for all sources. The G-band light curves and the characteristics of ∼3000 Cepheid and RR-Lyrae stars, observed at high cadence around the south ecliptic pole, form the third component. For the primary astrometric data set the typical uncertainty is about 0.3 mas for the positions and parallaxes, and about 1 mas yr−1 for the proper motions. A systematic component of ∼0.3 mas should be added to the parallax uncertainties. For the subset of ∼94 000 HIPPARCOS stars in the primary data set, the proper motions are much more precise at about 0.06 mas yr−1. For the secondary astrometric data set, the typical uncertainty of the positions is ∼10 mas. The median uncertainties on the mean G-band magnitudes range from the mmag level to ∼0.03 mag over the magnitude range 5 to 20.7. Conclusions. Gaia DR1 is an important milestone ahead of the next Gaia data release, which will feature five-parameter astrometry for all sources. Extensive validation shows that Gaia DR1 represents a major advance in the mapping of the heavens and the availability of basic stellar data that underpin observational astrophysics. Nevertheless, the very preliminary nature of this first Gaia data release does lead to a number of important limitations to the data quality which should be carefully considered before drawing conclusions from the data

A new Late Agenian (MN2a, Early Miocene) fossil assemblage from Wallenried (Molasse Basin, Canton Fribourg, Switzerland)

Excavations of two fossiliferous layers in the Wallenried sand- and marl pit produced a very diversified vertebrate fauna. New material allows the reassessment of the taxonomic position of the ruminant taxa Andegameryx andegaviensis and endemic Friburgomeryx wallenriedensis. An emended diagnosis for the second species is provided and additional material of large and small mammals, as well as ectothermic vertebrates, is described. The recorded Lagomorpha show interesting morphological deviations from other Central European material, and probably represent a unique transitional assemblage with a co-occurrence of Titanomys, Lagopsis and Prolagus. Rodentia and Eulipotyphla belong to typical and well-known species of the Agenian of the Swiss Molasse Basin. Abundant small mammal teeth have allowed us to pinpoint the biostratigraphic age of Wallenried to late MN2a. The biostratigraphic age conforms to data derived from the charophyte assemblages and confirms the oldest occurrence of venomous snake fangs. The palaeoenvironmental context is quite complex. Sedimentary structures and fauna (fishes, frogs, salamanders, ostracods) are characteristic for a humid, lacustrine environment within a flood plain system