Ormosils-PVA BOD sensing film based on oxygen luminescence quenching

2003-2004 > Academic research: refereed > Publication in refereed journalVersion of RecordPublishe

Femtosecond Carrier Dynamics in In2O3Nanocrystals

We have studied carrier dynamics in In2O3nanocrystals grown on a quartz substrate using chemical vapor deposition. Transient differential absorption measurements have been employed to investigate the relaxation dynamics of photo-generated carriers in In2O3nanocrystals. Intensity measurements reveal that Auger recombination plays a crucial role in the carrier dynamics for the carrier densities investigated in this study. A simple differential equation model has been utilized to simulate the photo-generated carrier dynamics in the nanocrystals and to fit the fluence-dependent differential absorption measurements. The average value of the Auger coefficient obtained from fitting to the measurements was γ = 5.9 ± 0.4 × 10−31 cm6 s−1. Similarly the average relaxation rate of the carriers was determined to be approximately τ = 110 ± 10 ps. Time-resolved measurements also revealed ~25 ps delay for the carriers to reach deep traps states which have a subsequent relaxation time of approximately 300 ps

Search for Charged Higgs Bosons in e+e- Collisions at \sqrt{s} = 189 GeV

A search for pair-produced charged Higgs bosons is performed with the L3 detector at LEP using data collected at a centre-of-mass energy of 188.6 GeV, corresponding to an integrated luminosity of 176.4 pb^-1. Higgs decays into a charm and a strange quark or into a tau lepton and its associated neutrino are considered. The observed events are consistent with the expectations from Standard Model background processes. A lower limit of 65.5 GeV on the charged Higgs mass is derived at 95 % confidence level, independent of the decay branching ratio Br(H^{+/-} -> tau nu)

Search for new phenomena in final states with an energetic jet and large missing transverse momentum in pp collisions at √ s = 8 TeV with the ATLAS detector

Results of a search for new phenomena in final states with an energetic jet and large missing transverse momentum are reported. The search uses 20.3 fb−1 of √ s = 8 TeV data collected in 2012 with the ATLAS detector at the LHC. Events are required to have at least one jet with pT > 120 GeV and no leptons. Nine signal regions are considered with increasing missing transverse momentum requirements between Emiss T > 150 GeV and Emiss T > 700 GeV. Good agreement is observed between the number of events in data and Standard Model expectations. The results are translated into exclusion limits on models with either large extra spatial dimensions, pair production of weakly interacting dark matter candidates, or production of very light gravitinos in a gauge-mediated supersymmetric model. In addition, limits on the production of an invisibly decaying Higgs-like boson leading to similar topologies in the final state are presente

Search for direct pair production of the top squark in all-hadronic final states in proton-proton collisions at s√=8 TeV with the ATLAS detector

The results of a search for direct pair production of the scalar partner to the top quark using an integrated luminosity of 20.1fb−1 of proton–proton collision data at √s = 8 TeV recorded with the ATLAS detector at the LHC are reported. The top squark is assumed to decay via t˜→tχ˜01 or t˜→ bχ˜±1 →bW(∗)χ˜01 , where χ˜01 (χ˜±1 ) denotes the lightest neutralino (chargino) in supersymmetric models. The search targets a fully-hadronic final state in events with four or more jets and large missing transverse momentum. No significant excess over the Standard Model background prediction is observed, and exclusion limits are reported in terms of the top squark and neutralino masses and as a function of the branching fraction of t˜ → tχ˜01 . For a branching fraction of 100%, top squark masses in the range 270–645 GeV are excluded for χ˜01 masses below 30 GeV. For a branching fraction of 50% to either t˜ → tχ˜01 or t˜ → bχ˜±1 , and assuming the χ˜±1 mass to be twice the χ˜01 mass, top squark masses in the range 250–550 GeV are excluded for χ˜01 masses below 60 GeV

Search for pair-produced long-lived neutral particles decaying to jets in the ATLAS hadronic calorimeter in ppcollisions at √s=8TeV

The ATLAS detector at the Large Hadron Collider at CERN is used to search for the decay of a scalar boson to a pair of long-lived particles, neutral under the Standard Model gauge group, in 20.3fb−1of data collected in proton–proton collisions at √s=8TeV. This search is sensitive to long-lived particles that decay to Standard Model particles producing jets at the outer edge of the ATLAS electromagnetic calorimeter or inside the hadronic calorimeter. No significant excess of events is observed. Limits are reported on the product of the scalar boson production cross section times branching ratio into long-lived neutral particles as a function of the proper lifetime of the particles. Limits are reported for boson masses from 100 GeVto 900 GeV, and a long-lived neutral particle mass from 10 GeVto 150 GeV

Unified representation of fixtures: Clamping, locating and supporting elements in CNC manufacture

International audienceA CNC machining operation is the outcome of the application of the integrated capabilities of various resources within the CNC machining centre. Part fixtures, clamping and other location mechanisms are essential subsets of CNC machining resources. Today, various fixturing techniques and attachments available on the market allow manufacturers to enhance their production capability without buying expensive machine tools. This technology rich fixturing domain is detached while representing and exchanging machine tool resource information for making manufacturing decisions. The research work in this paper utilizes the STEP-NC compliant Unified Manufacturing Resource Model (UMRM) for representing fixtures in conjunction with the parent CNC machining centre. Thus UMRM is enhanced in this context to represent various fixtures such as universal vises, chucks, pallets, auxiliary rotary tables among others. The major contribution of this paper is the application of the extension of the UMRM approach for representing fixturing domain, which allows generic modelling of fixtures and loading devices in addition to machine workpiece and process modelling. This would enable the stage of automated process planning and manufacturing. The universal approach in representing resource information allows the data to be utilised for making a wide variety of manufacturing decisions