2,980 research outputs found
Influence of Anodizing by Electro-Chemical Oxidation on Fatigue and Wear Resistance of the EV31A-T6 Cast Magnesium Alloy
In the last decades, several anodizing processes for Mg alloys have been proposed to achieve a good wear and corrosion resistance combination. In particular, Electro-Chemical Oxidation (ECO) showed an improved dense and compact anodized layer compared to other anodizing processes carried out above the dielectric breakdown voltage, such as Plasma Electrolytic Oxidation (PEO). However, the influence of the ECO treatment on the tribological behavior and cyclic mechanical performance of Mg alloys has not been investigated yet. This paper reports on the influence of ECO on dry sliding behavior (vs. 100Cr6 bearing steel (block-on-ring contact geometry)) and rotating bending fatigue performance of the rare earth (RE)-containing Mg alloy EV31A-T6, comparing it with both untreated EV31A-T6 and PEO-treated EV31A-T6, used as benchmarks. The ECO-treated alloy showed improved tribological behavior (critical load for coating failure one order of magnitude higher and coefficient of friction 40% lower than for PEO) and fatigue strength (no decrease for ECO-treated samples compared to the untreated alloy, while PEO-treated samples induced a 15% decrease) due to the increased compactness and lower defectivity of the anodized layer, induced by the minimization of destructive arc discharges during coating growth. In addition, the ECO treatment significantly improved wear resistance compared to the untreated alloy, avoiding, at the same time, the decrease in fatigue strength, which typically occurs after PEO. Therefore, the ECO process can be applied to improve wear resistance without decreasing the fatigue strength of high-performance components
Mechanical and microstructural features of wire-and-arc additively manufactured carbon steel thick plates
Metal additive manufacturing (AM), in particular wire-and-arc additive manufacturing (WAAM), has become over the last few years the breakthrough technology to reduce the environmental impact and increase the efficiency of steel structures. Although intense research effort has been paid toward the mechanical characterization of WAAM-produced thin walls, little attention has been devoted to the investigation of multi-layered thick parts. These latter would indeed expand the application of WAAM for large-scale constructions requiring thicker cross-sections to withstand high loading conditions. The present work provides a comprehensive experimental investigation of mild steel WAAM thick plates from the fabrication to the mechanical and microstructural characterization. First, the fabrication process is presented in full details. From that, microstructural and mechanical characterization is described and discussed, showing a homogeneous microstructure with little influence on the mechanical response along the wall plate thickness, also considering different specimen orientations with respect to the printing directions. The results confirm good mechanical properties of the printed outcomes, in line with those of structural mild steels manufactured with conventional technologies. Little influence on the response along the thickness is reported, thus proving the required quality of WAAM thick parts for applications in the construction sector
A new type of anti-ganglioside antibodies present in neurological patients
AbstractHigh titers of anti-GA1 antibodies have been associated with neurological syndromes. In most cases, these antibodies cross-react with the structurally related glycolipids GM1 and GD1b, although specific anti-GA1 antibodies have also been reported. The role of specific anti-GA1 antibodies is uncertain since the presence of GA1 in the human nervous system has not been clarified. A rabbit was immunized with GD1a and its sera were screened for antibody reactivity by standard immunoassay methods (HPTLC-immunostaining and ELISA). Anti-GD1a antibodies were not detected but, unexpectedly, anti-GA1 IgG-antibodies were found. Antibody binding to GA1 was inhibited by soluble GA1 but also by GD1a. These results indicate that the rabbit produced antibodies that recognize epitopes present on the glycolipids, that are absent or not exposed on solid phase adsorbed GD1a. We investigated the presence of these unusual anti-ganglioside antibodies in normal and neurological patient sera. Approximately, 10% of normal human sera contained low titer of specific anti-GA1 IgG-antibodies but none of them recognized soluble GD1a. High titers of IgG-antibodies reacting only with GA1 were detected in 12 patient sera out of 325 analyzed. Of these, 6 sera showed binding that was inhibited by soluble GD1a and four of them also by GM1. This new type of anti-ganglioside antibodies should be considered important elements for understanding of the pathogenesis of these diseases as well as their diagnosis
Comparison of direct and indirect methods to maximise the detection of Babesia caballi and Theileria equi infections in Central Southern Italy
: Equine piroplasmosis is a disease of equids, caused by tick-borne apicomplexan protozoan pathogens Babesia caballi and Theileria equi, which, according to the World Organisation for Animal Health (OIE), can be diagnosed by enzyme-linked immunosorbent assay (ELISA), immunofluorescent antibody test (IFAT) and polymerase chain reaction (PCR). The present study was conducted to evaluate and compare the assays available for the diagnosis of equine piroplasmosis. Data employed were obtained from 1300 blood samples collected between 2012-2014 from asymptomatic and symptomatic equines (horses and donkeys) of central-southern regions of Italy and analyzed by ELISA, IFAT, PCR (one commercial and one from literature) and blood smear microscopic examination. Statistical differences of the proportions of positivity for each parasite and group (asymptomatic and symptomatic) among the methods were verified by the z test to identify the most sensitive. The concordance between each pair of methods - for each parasite and within the groups - and trends in detection of suspect samples of four hypothetical diagnostic algorithms using serological and biomolecular assays were evaluated to identify the most suitable laboratory diagnostic workflow. The results of this study highlighted a lower capacity to detect suspect samples of commercial ELISA for B. caballi in all groups when compared to biomolecular methods and IFAT; and of the commercial PCRs in asymptomatic animals, identifying a PCR from literature and IFAT as the best choice for a combined diagnosis. For T. equi, IFAT detected more suspect samples than ELISA, even if the latter showed good performance and some samples were positive only by the ELISA and PCR, indicating that their simultaneous employment is still advantageous. Host-parasite interaction, amino-acid/genetic diversity and differences in detection limits among the assays could be among the reasons in explaining the present results. In view of further studies, ELISA should be used in combination with PCR, that should regularly be included in the laboratory diagnosis to maximise the detection of early infections and support the evaluation of pharmacological treatment
Effects of Isolation Period Difference and Beam-Column Stiffness Ratio on the Dynamic Response of Reinforced Concrete Buildings
Intercalibration of the barrel electromagnetic calorimeter of the CMS experiment at start-up
Calibration of the relative response of the individual channels of the barrel electromagnetic calorimeter of the CMS detector was accomplished, before installation, with cosmic ray muons and test beams. One fourth of the calorimeter was exposed to a beam of high energy electrons and the relative calibration of the channels, the intercalibration, was found to be reproducible to a precision of about 0.3%. Additionally, data were collected with cosmic rays for the entire ECAL barrel during the commissioning phase. By comparing the intercalibration constants obtained with the electron beam data with those from the cosmic ray data, it is demonstrated that the latter provide an intercalibration precision of 1.5% over most of the barrel ECAL. The best intercalibration precision is expected to come from the analysis of events collected in situ during the LHC operation. Using data collected with both electrons and pion beams, several aspects of the intercalibration procedures based on electrons or neutral pions were investigated
Bifurcation Equations Through Multiple-Scales Analysis for a Continuous Model of a Planar Beam
Search for massive resonances decaying in to WW,WZ or ZZ bosons in proton-proton collisions at root s=13 TeV
Peer reviewe
Measurement of the total cross section and Ï -parameter from elastic scattering in pp collisions at âs=13 TeV with the ATLAS detector
In a special run of the LHC with ÎČâ= 2.5 km, protonâproton elastic-scattering events were recorded at s=13 TeV with an integrated luminosity of 340ÎŒb-1 using the ALFA subdetector of ATLAS in 2016. The elastic cross section was measured differentially in the Mandelstam t variable in the range from - t= 2.5 · 10 - 4 GeV 2 to - t= 0.46 GeV 2 using 6.9 million elastic-scattering candidates. This paper presents measurements of the total cross section Ïtot , parameters of the nuclear slope, and the Ï -parameter defined as the ratio of the real part to the imaginary part of the elastic-scattering amplitude in the limit tâ 0 . These parameters are determined from a fit to the differential elastic cross section using the optical theorem and different parameterizations of the t-dependence. The results for Ïtot and Ï are Ïtot(ppâX)=104.7±1.1mb,Ï=0.098±0.011. The uncertainty in Ïtot is dominated by the luminosity measurement, and in Ï by imperfect knowledge of the detector alignment and by modelling of the nuclear amplitude
- âŠ