Characterization of Commercial Reverse Osmosis and Nanofiltration Membranes for Membrane Fouling

Membrane Filtration technique is being accepted worldwide as an environment friendly and energy efficient technique in Desalination Industry as compared to Thermal Desalination techniques. However, the performance of membranes which include permeate flux and rejection is affected by the membrane fouling. The properties of membrane and surface features such as porous structure, hydrophilicity/hydrophobicity charge, polymer characteristics, surface roughness determine the fouling potential of the membrane. The hydrophilic and smooth membrane surface is usually considered desirable in tackling membrane fouling issues. Therefore, many studies have focused on to enhance surface characteristics of membranes by surface coating with polymers and nanomaterials. Since, membrane coating is not done during fabrication of the most commercially available membranes, therefore, it is also important to determine the surface features of the commercially available membranes to investigate their membrane fouling potential. Thus, the objectives of this study were (1) to perform membrane surface characterization of commercial Reverse Osmosis (RO) and Nanofiltration (NF) membranes using techniques such as SEM, AFM, FTIR and XPS; (2) to measure hydrophilicity/hydrophobicity of commercial RO and NF membranes through water contact angle measurement using sessile drop method and (3) to measure the flux and percentage rejection of NF and RO membranes using Dead end filtration technique. Here, the characterization of membrane surface in terms of surface roughness, using SEM and AFM, showed that the commercial RO membrane had more ridge and valley structures and higher average surface roughness i.e. 71.24 nm as compared to NF membranes (6.63 nm). In addition, water contact angle measurements showed that the NF membrane was more hydrophilic as compared to RO membrane. The average contact angle found for RO membrane was 59.94°. On the other hand, it was observed that NF membrane is extremely hydrophilic in nature. Due to which, contact angle value was not obtained for most of the runs. The droplet could diffuse in less than 5 seconds. In addition, the dead-end filtration experiments showed that the RO membrane had much lower flux as compared to NF membrane. This can be associated with the pore structure of these membranes. Since, the NF membrane has porous structure, in oppose to RO membrane, the flux of the NF membrane is usually higher than the RO membranes. As the membrane surface roughness and hydrophobicity makes it more susceptible to the fouling leading to reduction in membrane flux and performance, it can be concluded from this study that there is a need for surface coating of RO membrane with suitable nanomaterials such as graphene oxide to improve its hydrophilicity and surface smoothness. This will eventually make the membrane more resistant to membrane fouling and will establish the use of membrane filtration technique in desalination industry in Qatar in the future. Microorganisms have been isolated from Gulf sea water, identified and differentiated and are being used to study the biofouling of RO and NF membranes, that would be coated to limit the fouling problems. Acknowledgement: This research was made possible by NPRP grant # [9-318-1-064] from the Qatar National Research Fund (a member of Qatar Foundation). The findings achieved herein are solely the responsibility of the author[s].qscienc

A new ceramide along with eight known compounds from the roots of Artemisia incisa pamp

A new compound (1) (named as artemceramide-B) together with eight known compounds (taraxerol (2), taraxerol acetate (3), β-sitosterol (4), stigmasterol (5), trans-ethyl caffeate, dracunculin (7), scoparone (8) and isoscopoletin (9) were isolated from an ethanolic extract of the roots of Artemisia incisa Pamp (Asteracae). The structures of the compounds were determined through IR, 1D NMR (1H NMR, 13C NMR) and 2D NMR (COSY, NOESY, HSQC and HMBC) analyses. Accurate mass analyses were done with EI-MS, ESI-MS and acid methanolysis of compound 1 followed by GS-MS studies. The relative stereochemistry of artemceramide-B was determined by comparing its specific rotation and spectroscopic data with the literature. Compounds 1-9 were tested for their anti-bacterial potential against five bacteria strains; Staphylococcus epidermidis, Staphylococcus aureus, Klebsiella pneumoniae, Bacillus subtilis and Escherichia coli. Compound 1 (new) (MIC: 0.0157, 0.0313 mg/mL) and 7 (MIC: 0.0815 , 1.000 mg/mL) showed excellent activities against S. epidermidis and S. aureus while compound 9 showed excellent activities (MIC: 0.0700 , 1.234, 1.890 and 2.286 mg/mL) against S. epidermidis,S. aureus, K. pneumoniae and E. coli, respectively. Compound 6 (MIC: 2.000 mg/mL) was found to be active against E. coli while neither of the compounds showed potential activity against B. subtilis

Performance Analysis of YOLO-based Architectures for Vehicle Detection from Traffic Images in Bangladesh

The task of locating and classifying different types of vehicles has become a vital element in numerous applications of automation and intelligent systems ranging from traffic surveillance to vehicle identification and many more. In recent times, Deep Learning models have been dominating the field of vehicle detection. Yet, Bangladeshi vehicle detection has remained a relatively unexplored area. One of the main goals of vehicle detection is its real-time application, where `You Only Look Once' (YOLO) models have proven to be the most effective architecture. In this work, intending to find the best-suited YOLO architecture for fast and accurate vehicle detection from traffic images in Bangladesh, we have conducted a performance analysis of different variants of the YOLO-based architectures such as YOLOV3, YOLOV5s, and YOLOV5x. The models were trained on a dataset containing 7390 images belonging to 21 types of vehicles comprising samples from the DhakaAI dataset, the Poribohon-BD dataset, and our self-collected images. After thorough quantitative and qualitative analysis, we found the YOLOV5x variant to be the best-suited model, performing better than YOLOv3 and YOLOv5s models respectively by 7 & 4 percent in mAP, and 12 & 8.5 percent in terms of Accuracy.Comment: Accepted in 25th ICCIT (6 pages, 5 figures, 1 table

An Efficient and Secure Energy Trading Approach with Machine Learning Technique and Consortium Blockchain

In this paper, a secure energy trading mechanism based on blockchain technology is proposed. The proposed model deals with energy trading problems such as insecure energy trading and inefficient charging mechanisms for electric vehicles (EVs) in a vehicular energy network (VEN). EVs face two major problems: finding an optimal charging station and calculating the exact amount of energy required to reach the selected charging station. Moreover, in traditional trading approaches, centralized parties are involved in energy trading, which leads to various issues such as increased computational cost, increased computational delay, data tempering and a single point of failure. Furthermore, EVs face various energy challenges, such as imbalanced load supply and fluctuations in voltage level. Therefore, a demand-response (DR) pricing strategy enables EV users to flatten load curves and efficiently adjust electricity usage. In this work, communication between EVs and aggregators is efficiently performed through blockchain. Moreover, a branching concept is involved in the proposed system, which divides EV data into two different branches: a Fraud Chain (F-chain) and an Integrity Chain (I-chain). The proposed branching mechanism helps solve the storage problem and reduces computational time. Moreover, an attacker model is designed to check the robustness of the proposed system against double-spending and replay attacks. Security analysis of the proposed smart contract is also given in this paper. Simulation results show that the proposed work efficiently reduces the charging cost and time in a VEN.publishedVersio

The global burden of cancer attributable to risk factors, 2010-19 : a systematic analysis for the Global Burden of Disease Study 2019

Background Understanding the magnitude of cancer burden attributable to potentially modifiable risk factors is crucial for development of effective prevention and mitigation strategies. We analysed results from the Global Burden of Diseases, Injuries, and Risk Factors Study (GBD) 2019 to inform cancer control planning efforts globally. Methods The GBD 2019 comparative risk assessment framework was used to estimate cancer burden attributable to behavioural, environmental and occupational, and metabolic risk factors. A total of 82 risk-outcome pairs were included on the basis of the World Cancer Research Fund criteria. Estimated cancer deaths and disability-adjusted life-years (DALYs) in 2019 and change in these measures between 2010 and 2019 are presented. Findings Globally, in 2019, the risk factors included in this analysis accounted for 4.45 million (95% uncertainty interval 4.01-4.94) deaths and 105 million (95.0-116) DALYs for both sexes combined, representing 44.4% (41.3-48.4) of all cancer deaths and 42.0% (39.1-45.6) of all DALYs. There were 2.88 million (2.60-3.18) risk-attributable cancer deaths in males (50.6% [47.8-54.1] of all male cancer deaths) and 1.58 million (1.36-1.84) risk-attributable cancer deaths in females (36.3% [32.5-41.3] of all female cancer deaths). The leading risk factors at the most detailed level globally for risk-attributable cancer deaths and DALYs in 2019 for both sexes combined were smoking, followed by alcohol use and high BMI. Risk-attributable cancer burden varied by world region and Socio-demographic Index (SDI), with smoking, unsafe sex, and alcohol use being the three leading risk factors for risk-attributable cancer DALYs in low SDI locations in 2019, whereas DALYs in high SDI locations mirrored the top three global risk factor rankings. From 2010 to 2019, global risk-attributable cancer deaths increased by 20.4% (12.6-28.4) and DALYs by 16.8% (8.8-25.0), with the greatest percentage increase in metabolic risks (34.7% [27.9-42.8] and 33.3% [25.8-42.0]). Interpretation The leading risk factors contributing to global cancer burden in 2019 were behavioural, whereas metabolic risk factors saw the largest increases between 2010 and 2019. Reducing exposure to these modifiable risk factors would decrease cancer mortality and DALY rates worldwide, and policies should be tailored appropriately to local cancer risk factor burden. Copyright (C) 2022 The Author(s). Published by Elsevier Ltd. This is an Open Access article under the CC BY 4.0 license.Peer reviewe

Effects of a high-dose 24-h infusion of tranexamic acid on death and thromboembolic events in patients with acute gastrointestinal bleeding (HALT-IT): an international randomised, double-blind, placebo-controlled trial

Background: Tranexamic acid reduces surgical bleeding and reduces death due to bleeding in patients with trauma. Meta-analyses of small trials show that tranexamic acid might decrease deaths from gastrointestinal bleeding. We aimed to assess the effects of tranexamic acid in patients with gastrointestinal bleeding. Methods: We did an international, multicentre, randomised, placebo-controlled trial in 164 hospitals in 15 countries. Patients were enrolled if the responsible clinician was uncertain whether to use tranexamic acid, were aged above the minimum age considered an adult in their country (either aged 16 years and older or aged 18 years and older), and had significant (defined as at risk of bleeding to death) upper or lower gastrointestinal bleeding. Patients were randomly assigned by selection of a numbered treatment pack from a box containing eight packs that were identical apart from the pack number. Patients received either a loading dose of 1 g tranexamic acid, which was added to 100 mL infusion bag of 0·9% sodium chloride and infused by slow intravenous injection over 10 min, followed by a maintenance dose of 3 g tranexamic acid added to 1 L of any isotonic intravenous solution and infused at 125 mg/h for 24 h, or placebo (sodium chloride 0·9%). Patients, caregivers, and those assessing outcomes were masked to allocation. The primary outcome was death due to bleeding within 5 days of randomisation; analysis excluded patients who received neither dose of the allocated treatment and those for whom outcome data on death were unavailable. This trial was registered with Current Controlled Trials, ISRCTN11225767, and ClinicalTrials.gov, NCT01658124. Findings: Between July 4, 2013, and June 21, 2019, we randomly allocated 12 009 patients to receive tranexamic acid (5994, 49·9%) or matching placebo (6015, 50·1%), of whom 11 952 (99·5%) received the first dose of the allocated treatment. Death due to bleeding within 5 days of randomisation occurred in 222 (4%) of 5956 patients in the tranexamic acid group and in 226 (4%) of 5981 patients in the placebo group (risk ratio [RR] 0·99, 95% CI 0·82–1·18). Arterial thromboembolic events (myocardial infarction or stroke) were similar in the tranexamic acid group and placebo group (42 [0·7%] of 5952 vs 46 [0·8%] of 5977; 0·92; 0·60 to 1·39). Venous thromboembolic events (deep vein thrombosis or pulmonary embolism) were higher in tranexamic acid group than in the placebo group (48 [0·8%] of 5952 vs 26 [0·4%] of 5977; RR 1·85; 95% CI 1·15 to 2·98). Interpretation: We found that tranexamic acid did not reduce death from gastrointestinal bleeding. On the basis of our results, tranexamic acid should not be used for the treatment of gastrointestinal bleeding outside the context of a randomised trial

Optimasi Portofolio Resiko Menggunakan Model Markowitz MVO Dikaitkan dengan Keterbatasan Manusia dalam Memprediksi Masa Depan dalam Perspektif Al-Qur`an

Risk portfolio on modern finance has become increasingly technical, requiring the use of sophisticated mathematical tools in both research and practice. Since companies cannot insure themselves completely against risk, as human incompetence in predicting the future precisely that written in Al-Quran surah Luqman verse 34, they have to manage it to yield an optimal portfolio. The objective here is to minimize the variance among all portfolios, or alternatively, to maximize expected return among all portfolios that has at least a certain expected return. Furthermore, this study focuses on optimizing risk portfolio so called Markowitz MVO (Mean-Variance Optimization). Some theoretical frameworks for analysis are arithmetic mean, geometric mean, variance, covariance, linear programming, and quadratic programming. Moreover, finding a minimum variance portfolio produces a convex quadratic programming, that is minimizing the objective function ðð¥with constraintsð ð 𥠥 ðandð´ð¥ = ð. The outcome of this research is the solution of optimal risk portofolio in some investments that could be finished smoothly using MATLAB R2007b software together with its graphic analysis

Measurement of the top quark forward-backward production asymmetry and the anomalous chromoelectric and chromomagnetic moments in pp collisions at √s = 13 TeV

Abstract The parton-level top quark (t) forward-backward asymmetry and the anomalous chromoelectric (d̂ t) and chromomagnetic (μ̂ t) moments have been measured using LHC pp collisions at a center-of-mass energy of 13 TeV, collected in the CMS detector in a data sample corresponding to an integrated luminosity of 35.9 fb−1. The linearized variable AFB(1) is used to approximate the asymmetry. Candidate t t ¯ events decaying to a muon or electron and jets in final states with low and high Lorentz boosts are selected and reconstructed using a fit of the kinematic distributions of the decay products to those expected for t t ¯ final states. The values found for the parameters are AFB(1)=0.048−0.087+0.095(stat)−0.029+0.020(syst),μ̂t=−0.024−0.009+0.013(stat)−0.011+0.016(syst), and a limit is placed on the magnitude of | d̂ t| < 0.03 at 95% confidence level. [Figure not available: see fulltext.

An embedding technique to determine ττ backgrounds in proton-proton collision data

An embedding technique is presented to estimate standard model tau tau backgrounds from data with minimal simulation input. In the data, the muons are removed from reconstructed mu mu events and replaced with simulated tau leptons with the same kinematic properties. In this way, a set of hybrid events is obtained that does not rely on simulation except for the decay of the tau leptons. The challenges in describing the underlying event or the production of associated jets in the simulation are avoided. The technique described in this paper was developed for CMS. Its validation and the inherent uncertainties are also discussed. The demonstration of the performance of the technique is based on a sample of proton-proton collisions collected by CMS in 2017 at root s = 13 TeV corresponding to an integrated luminosity of 41.5 fb(-1).Peer reviewe

Measurement of t(t)over-bar normalised multi-differential cross sections in pp collisions at root s=13 TeV, and simultaneous determination of the strong coupling strength, top quark pole mass, and parton distribution functions

Peer reviewe