BAJAS CONCENTRACIONES DE LANTANO EN LA SOLUCIÓN NUTRITIVA INCREMENTAN LA VIDA DE LA FLOR EN MACETA DE DOS VARIEDADES DE LISIANTHUS

This study evaluated the effect of the addition of La (0, 10, 20 and 30 uM) from two sources [La(NO3)3 6H2O and LaCl3] in the Steiner nutrient solution at 50%, in phenology [beginning of flowering (IF), floral opening (AF), full flowering (PF) and initiation of senescence (IS)], and in the duration of flower stems in pot (pot life (VM)] of two commercial varieties of lisianthus (varieties Mariachi Blue and Echo Lavanda). In both varieties, the treatment with La, regardless of the source used, delays the IF, the AF, the PF and the IS. This delay can be important considering aspects related to the market. Likewise, it was observed that the low concentration of La evaluated (10 uM) significantly increased the life of the flower in pot in the two varieties of lisianthus. These results allow us to conclude that it is an element that has beneficial effects in lisianthus, and that the observed effects are dependent on its concentration.Este estudio evaluó el efecto de la adición de La a la solución nutritiva de Steiner al 50% (0, 10, 20 y 30 uM) a partir de dos fuentes [La(NO3)3 6H2O y LaCl3], en la fenología [inicio de floración (IF), apertura floral (AF), plena floración (PF) e inicio de senescencia (IS)], y en la duración de los tallos florales en maceta [vida en maceta (VM)] de dos variedades comerciales de lisianthus (Mariachi Blue y Echo Lavanda). En ambas variedades, el tratamiento con La, independientemente de la fuente empleada, retrasa el IF, la AP, la PF y el IS. Este retraso puede ser importante si se consideran aspectos relacionados con el mercado. Asimismo, se observó que la concentración baja de La evaluada (10 uM) incrementa significativamente la vida de la flor en maceta en las dos variedades de lisianthus. Estos resultados permiten concluir que el La es un elemento que tiene efectos benéficos en lisianthus, y que los efectos observados son dependientes de su concentració

Residual Forage and Animal Performance from a Kikuyo Pasture under Mixed Grazing and Supplementation

Five grazing strategies were compared: grazing by ewes only and mixed grazing (ewes + heifers), in mixed grazing heifers received no supplement or one of three supplements. Ruminal undegradable protein (RUP) varied among supplement: 4.25, 9.11 and 9.13%, the supplement with the highest RUP included protected methionine. All supplements were 21% crude protein and 3.0 Mcal/kg of metabolizable energy. Grazing was on kikuyu, ratio was 30 kg of ewe per 100 kg of heifer in the mixed grazing treatments. Experimental grazing lasted 84 days. Variables measured were residual forage, proline content in residual forage and liveweight gains per animal and per hectare. Experimental design was a completely random with two replicates. Residual forage was the highest (P\u3c 0.05) in mixed grazing and RUP in supplement was above 4.25%. The highest (P\u3c 0.05) proline content was found in grazing by ewes only, 52% above the proline content found in mixed grazing without supplement, when heifers received supplement proline content decreased (P\u3c 0.05) further. Grazing by ewes only and mixed grazing with heifersreceiving the highest RUP in supplement showed the highest (P\u3c 0.05) daily liveweight gain per ewe of 134 g. Mixed grazing in which heifers received no supplement gave a 100% increase (P\u3c 0.05) in liveweight gain per hectare compared to grazing by ewes only. In mixed grazing offering a supplement with 9.13% RUP and protected methionine gave both the highest liveweight gains per animal and per hectare. It was concluded that mixed grazing allowed a lower stress level on kikuyu due to defoliation and a higher liveweight gain per hectare than grazing by ewes only

Identification of Cinnabar by non-Destructive Techniques on a Human Mandible from Carrer Paris Chalcolithic Hypogeum (Cerdanyola del Vallès, Barcelona, Spain)

The Carrer Paris site is located in Cerdanyola del Vallès (Barcelona, Spain). It is a Chalcolithic hypogeum dated between 3800-4100 BP with more than 60 individuals distributed in four burial levels. We study the remains of Individual 5 from burial level II. It is an adult skeleton, preserved in anatomical position and buried with Campaniform pottery. During the excavation, we identified red pigment on the mandibular symphysis region of the individual 5. In this work we present the preservation state and conservation methodology to restore the individual 5 cranium and mandible. At the same time, we present the results of the pigment composition analyzed by non-destructive methods. These analyses were conducted directly on the pigments and the bone surface with environment electronic microscopy (ESEM-EDS) X-ray micro-diffraction (µ-DRX) before the conservation treatments. The objective of the analysis was to characterize the pigments, the bone and the clays to apply the best methodology to conserve the pieces. The combination of both techniques allows us to analyze the area of interest without removing samples. These analyses were performed directly, without affecting the bone and pigments and assuring the integral preservation of the objects. The results reach us new data on the use of pigment in funerary rituals during the Chalcolithic.L’hypogée du Chalcolithique de la Rue Paris (Cerdanyola del Vallès, Barcelona, Espagne) a été daté entre 3800 et 4100 BP. Les restes anthropologiques fouillés étaient distribués sur quatre niveaux et dépassaient les 60 individus. Ceux étudiés ici proviennent du deuxième niveau d’inhumation et appartiennent à un squelette adulte (individu 5), préservé en connexion anatomique et inhumé avec de la céramique campaniforme. Au cours de la fouille, des restes de matière colorante rouge ont été identifiés sur la région de la symphyse mentonnière. Dans ce travail sont présentés l’état de conservation et la méthodologie de restauration du crâne et de la mandibule de l’individu 5. De même, sont présentés les résultats des analyses non destructices faites directement sur les matières colorantes et l’os. Les analyses ont été réalisées avant la restauration du crâne et de la mandibule à l’aide d’un microscope électronique à balayage environnemental (ESEM-EDS) et micro-diffraction de rayons X (µ-DRX). L’objectif des analyses est la caractérisation des pigments, de l’os et du sédiment afin de choisir la meilleure méthodologie à appliquer pour la conservation des pièces. La combinaison de ces techniques favorise l’analyse des zones d’intérêt sans la prise d’échantillons. Ces analyses ont été faites directement sans abîmer l’os ni les pigments et, en conséquence, la préservation intégrale des objets est assurée. Les résultats obtenus apportent une information importante à propos de l’utilisation de quelques matières colorantes dans les rituels funéraires au Chalcolithique

Multiscale modelling for fusion and fission materials: the M4F project

The M4F project brings together the fusion and fission materials communities working on the prediction of radiation damage production and evolution and its effects on the mechanical behaviour of irradiated ferritic/martensitic (F/M) steels. It is a multidisciplinary project in which several different experimental and computational materials science tools are integrated to understand and model the complex phenomena associated with the formation and evolution of irradiation induced defects and their effects on the macroscopic behaviour of the target materials. In particular the project focuses on two specific aspects: (1) To develop physical understanding and predictive models of the origin and consequences of localised deformation under irradiation in F/M steels; (2) To develop good practices and possibly advance towards the definition of protocols for the use of ion irradiation as a tool to evaluate radiation effects on materials. Nineteen modelling codes across different scales are being used and developed and an experimental validation programme based on the examination of materials irradiated with neutrons and ions is being carried out. The project enters now its 4th year and is close to delivering high-quality results. This paper overviews the work performed so far within the project, highlighting its impact for fission and fusion materials science.This work has received funding from the Euratom research and training programme 2014-2018 under grant agreement No. 755039 (M4F project)

Production and processing of graphene and related materials

© 2020 The Author(s). We present an overview of the main techniques for production and processing of graphene and related materials (GRMs), as well as the key characterization procedures. We adopt a 'hands-on' approach, providing practical details and procedures as derived from literature as well as from the authors' experience, in order to enable the reader to reproduce the results. Section I is devoted to 'bottom up' approaches, whereby individual constituents are pieced together into more complex structures. We consider graphene nanoribbons (GNRs) produced either by solution processing or by on-surface synthesis in ultra high vacuum (UHV), as well carbon nanomembranes (CNM). Production of a variety of GNRs with tailored band gaps and edge shapes is now possible. CNMs can be tuned in terms of porosity, crystallinity and electronic behaviour. Section II covers 'top down' techniques. These rely on breaking down of a layered precursor, in the graphene case usually natural crystals like graphite or artificially synthesized materials, such as highly oriented pyrolythic graphite, monolayers or few layers (FL) flakes. The main focus of this section is on various exfoliation techniques in a liquid media, either intercalation or liquid phase exfoliation (LPE). The choice of precursor, exfoliation method, medium as well as the control of parameters such as time or temperature are crucial. A definite choice of parameters and conditions yields a particular material with specific properties that makes it more suitable for a targeted application. We cover protocols for the graphitic precursors to graphene oxide (GO). This is an important material for a range of applications in biomedicine, energy storage, nanocomposites, etc. Hummers' and modified Hummers' methods are used to make GO that subsequently can be reduced to obtain reduced graphene oxide (RGO) with a variety of strategies. GO flakes are also employed to prepare three-dimensional (3d) low density structures, such as sponges, foams, hydro- or aerogels. The assembly of flakes into 3d structures can provide improved mechanical properties. Aerogels with a highly open structure, with interconnected hierarchical pores, can enhance the accessibility to the whole surface area, as relevant for a number of applications, such as energy storage. The main recipes to yield graphite intercalation compounds (GICs) are also discussed. GICs are suitable precursors for covalent functionalization of graphene, but can also be used for the synthesis of uncharged graphene in solution. Degradation of the molecules intercalated in GICs can be triggered by high temperature treatment or microwave irradiation, creating a gas pressure surge in graphite and exfoliation. Electrochemical exfoliation by applying a voltage in an electrolyte to a graphite electrode can be tuned by varying precursors, electrolytes and potential. Graphite electrodes can be either negatively or positively intercalated to obtain GICs that are subsequently exfoliated. We also discuss the materials that can be amenable to exfoliation, by employing a theoretical data-mining approach. The exfoliation of LMs usually results in a heterogeneous dispersion of flakes with different lateral size and thickness. This is a critical bottleneck for applications, and hinders the full exploitation of GRMs produced by solution processing. The establishment of procedures to control the morphological properties of exfoliated GRMs, which also need to be industrially scalable, is one of the key needs. Section III deals with the processing of flakes. (Ultra)centrifugation techniques have thus far been the most investigated to sort GRMs following ultrasonication, shear mixing, ball milling, microfluidization, and wet-jet milling. It allows sorting by size and thickness. Inks formulated from GRM dispersions can be printed using a number of processes, from inkjet to screen printing. Each technique has specific rheological requirements, as well as geometrical constraints. The solvent choice is critical, not only for the GRM stability, but also in terms of optimizing printing on different substrates, such as glass, Si, plastic, paper, etc, all with different surface energies. Chemical modifications of such substrates is also a key step. Sections IV-VII are devoted to the growth of GRMs on various substrates and their processing after growth to place them on the surface of choice for specific applications. The substrate for graphene growth is a key determinant of the nature and quality of the resultant film. The lattice mismatch between graphene and substrate influences the resulting crystallinity. Growth on insulators, such as SiO2, typically results in films with small crystallites, whereas growth on the close-packed surfaces of metals yields highly crystalline films. Section IV outlines the growth of graphene on SiC substrates. This satisfies the requirements for electronic applications, with well-defined graphene-substrate interface, low trapped impurities and no need for transfer. It also allows graphene structures and devices to be measured directly on the growth substrate. The flatness of the substrate results in graphene with minimal strain and ripples on large areas, allowing spectroscopies and surface science to be performed. We also discuss the surface engineering by intercalation of the resulting graphene, its integration with Si-wafers and the production of nanostructures with the desired shape, with no need for patterning. Section V deals with chemical vapour deposition (CVD) onto various transition metals and on insulators. Growth on Ni results in graphitized polycrystalline films. While the thickness of these films can be optimized by controlling the deposition parameters, such as the type of hydrocarbon precursor and temperature, it is difficult to attain single layer graphene (SLG) across large areas, owing to the simultaneous nucleation/growth and solution/precipitation mechanisms. The differing characteristics of polycrystalline Ni films facilitate the growth of graphitic layers at different rates, resulting in regions with differing numbers of graphitic layers. High-quality films can be grown on Cu. Cu is available in a variety of shapes and forms, such as foils, bulks, foams, thin films on other materials and powders, making it attractive for industrial production of large area graphene films. The push to use CVD graphene in applications has also triggered a research line for the direct growth on insulators. The quality of the resulting films is lower than possible to date on metals, but enough, in terms of transmittance and resistivity, for many applications as described in section V. Transfer technologies are the focus of section VI. CVD synthesis of graphene on metals and bottom up molecular approaches require SLG to be transferred to the final target substrates. To have technological impact, the advances in production of high-quality large-area CVD graphene must be commensurate with those on transfer and placement on the final substrates. This is a prerequisite for most applications, such as touch panels, anticorrosion coatings, transparent electrodes and gas sensors etc. New strategies have improved the transferred graphene quality, making CVD graphene a feasible option for CMOS foundries. Methods based on complete etching of the metal substrate in suitable etchants, typically iron chloride, ammonium persulfate, or hydrogen chloride although reliable, are time- and resourceconsuming, with damage to graphene and production of metal and etchant residues. Electrochemical delamination in a low-concentration aqueous solution is an alternative. In this case metallic substrates can be reused. Dry transfer is less detrimental for the SLG quality, enabling a deterministic transfer. There is a large range of layered materials (LMs) beyond graphite. Only few of them have been already exfoliated and fully characterized. Section VII deals with the growth of some of these materials. Amongst them, h-BN, transition metal tri- and di-chalcogenides are of paramount importance. The growth of h-BN is at present considered essential for the development of graphene in (opto) electronic applications, as h-BN is ideal as capping layer or substrate. The interesting optical and electronic properties of TMDs also require the development of scalable methods for their production. Large scale growth using chemical/physical vapour deposition or thermal assisted conversion has been thus far limited to a small set, such as h-BN or some TMDs. Heterostructures could also be directly grown

Implementation and performance of the high level trigger electron and photon selection for the ATLAS experiment at the LHC

International audienceThe ATLAS experiment at the Large Hadron Collider (LHC) will face the challenge of efficiently selecting interesting candidate events in pp collisions at 14 TeV center of mass energy, while rejecting the enormous number of background events, stemming from an interaction rate of up to 10/sup 9/ Hz. The Level1 trigger will reduce this rate to around /spl Oscr/(100kHz). Subsequently, the high level trigger (HLT), which is comprised of the Second Level trigger and the Event Filter, will need to reduce this rate further by a factor of /spl Oscr/(10/sup 3/). The HLT selection is software based and will be implemented on commercial CPUs using a common framework built on the standard ATLAS object oriented software architecture. In this paper an overview of the current implementation of the selection for electrons and photons in the HLT is given. The performance of this implementation has been evaluated using Monte Carlo simulations in terms of the efficiency for the signal channels, rate expected for the selection, data preparation times, and algorithm execution times. Besides the efficiency and rate estimates, some physics examples will be discussed, showing that the triggers are well adapted for the physics programme envisaged at LHC. The electron and photon trigger software is also being exercised at the ATLAS 2004 Combined Test Beam, where components from all ATLAS subdetectors are taking data together along the H8 SPS extraction line; from these tests a validation of the selection architecture chosen in a real on-line environment is expected

Host adaptive immunity deficiency in severe pandemic influenza

INTRODUCTION: Pandemic A/H1N1/2009 influenza causes severe lower respiratory complications in rare cases. The association between host immune responses and clinical outcome in severe cases is unknown. METHODS: We utilized gene expression, cytokine profiles and generation of antibody responses following hospitalization in 19 critically ill patients with primary pandemic A/H1N1/2009 influenza pneumonia for identifying host immune responses associated with clinical outcome. Ingenuity pathway analysis 8.5 (IPA) (Ingenuity Systems, Redwood City, CA) was used to select, annotate and visualize genes by function and pathway (gene ontology). IPA analysis identified those canonical pathways differentially expressed (P < 0.05) between comparison groups. Hierarchical clustering of those genes differentially expressed between groups by IPA analysis was performed using BRB-Array Tools v.3.8.1. RESULTS: The majority of patients were characterized by the presence of comorbidities and the absence of immunosuppressive conditions. pH1N1 specific antibody production was observed around day 9 from disease onset and defined an early period of innate immune response and a late period of adaptive immune response to the virus. The most severe patients (n = 12) showed persistence of viral secretion. Seven of the most severe patients died. During the late phase, the most severe patient group had impaired expression of a number of genes participating in adaptive immune responses when compared to less severe patients. These genes were involved in antigen presentation, B-cell development, T-helper cell differentiation, CD28, granzyme B signaling, apoptosis and protein ubiquitination. Patients with the poorest outcomes were characterized by proinflammatory hypercytokinemia, along with elevated levels of immunosuppressory cytokines (interleukin (IL)-10 and IL-1ra) in serum. CONCLUSIONS: Our findings suggest an impaired development of adaptive immunity in the most severe cases of pandemic influenza, leading to an unremitting cycle of viral replication and innate cytokine-chemokine release. Interruption of this deleterious cycle may improve disease outcome.The study was scientifically sponsored by the Spanish Society for Critical Care Medicine (SEMICYUC). Funding: MICCIN-FIS/JCYL-IECSCYL-SACYL (Spain): Programa de Investigación Comisionada en Gripe, GR09/0021-EMER07/050- PI081236-RD07/0067. CIHR-NIH-Sardinia Recherché-LKSF Canada support DJK.S

Flow cytometry for fast screening and automated risk assessment in systemic light-chain amyloidosis

Early diagnosis and risk stratification are key to improve outcomes in light-chain (AL) amyloidosis. Here we used multidimensional-flow-cytometry (MFC) to characterize bone marrow (BM) plasma cells (PCs) from a series of 166 patients including newly-diagnosed AL amyloidosis (N = 94), MGUS (N = 20) and multiple myeloma (MM, N = 52) vs. healthy adults (N = 30). MFC detected clonality in virtually all AL amyloidosis (99%) patients. Furthermore, we developed an automated risk-stratification system based on BMPCs features, with independent prognostic impact on progression-free and overall survival of AL amyloidosis patients (hazard ratio: ≥ 2.9;P ≤ .03). Simultaneous assessment of the clonal PCs immunophenotypic protein expression profile and the BM cellular composition, mapped AL amyloidosis in the crossroad between MGUS and MM; however, lack of homogenously-positive CD56 expression, reduction of B-cell precursors and a predominantly-clonal PC compartment in the absence of an MM-like tumor PC expansion, emerged as hallmarks of AL amyloidosis (ROC-AUC = 0.74;P < .001), and might potentially be used as biomarkers for the identification of MGUS and MM patients, who are candidates for monitoring pre-symptomatic organ damage related to AL amyloidosis. Altogether, this study addressed the need for consensus on how to use flow cytometry in AL amyloidosis, and proposes a standardized MFC-based automated risk classification ready for implementation in clinical practice

Evolution after Anti-TNF Discontinuation in Patients with Inflammatory Bowel Disease: A Multicenter Long-Term Follow-Up Study

OBJECTIVES:The aims of this study were to assess the risk of relapse after discontinuation of anti-tumor necrosis factor (anti-TNF) drugs in patients with inflammatory bowel disease (IBD), to identify the factors associated with relapse, and to evaluate the overcome after retreatment with the same anti-TNF in those who relapsed.METHODS:This was a retrospective, observational, multicenter study. IBD patients who had been treated with anti-TNFs and in whom these drugs were discontinued after clinical remission was achieved were included.RESULTS:A total of 1, 055 patients were included. The incidence rate of relapse was 19% and 17% per patient-year in Crohn''s disease and ulcerative colitis patients, respectively. In both Crohn''s disease and ulcerative colitis patients in deep remission, the incidence rate of relapse was 19% per patient-year. The treatment with adalimumab vs. infliximab (hazard ratio (HR)=1.29; 95% confidence interval (CI)=1.01-1.66), elective discontinuation of anti-TNFs (HR=1.90; 95% CI=1.07-3.37) or discontinuation because of adverse events (HR=2.33; 95% CI=1.27-2.02) vs. a top-down strategy, colonic localization (HR=1.51; 95% CI=1.13-2.02) vs. ileal, and stricturing behavior (HR=1.5; 95% CI=1.09-2.05) vs. inflammatory were associated with a higher risk of relapse in Crohn''s disease patients, whereas treatment with immunomodulators after discontinuation (HR=0.67; 95% CI=0.51-0.87) and age (HR=0.98; 95% CI=0.97-0.99) were protective factors. None of the factors were predictive in ulcerative colitis patients. Retreatment of relapse with the same anti-TNF was effective (80% responded) and safe.CONCLUSIONS:The incidence rate of inflammatory bowel disease relapse after anti-TNF discontinuation is relevant. Some predictive factors of relapse after anti-TNF withdrawal have been identified. Retreatment with the same anti-TNF drug was effective and safe

Production and processing of graphene and related materials

© 2020 The Author(s). We present an overview of the main techniques for production and processing of graphene and related materials (GRMs), as well as the key characterization procedures. We adopt a 'hands-on' approach, providing practical details and procedures as derived from literature as well as from the authors' experience, in order to enable the reader to reproduce the results. Section I is devoted to 'bottom up' approaches, whereby individual constituents are pieced together into more complex structures. We consider graphene nanoribbons (GNRs) produced either by solution processing or by on-surface synthesis in ultra high vacuum (UHV), as well carbon nanomembranes (CNM). Production of a variety of GNRs with tailored band gaps and edge shapes is now possible. CNMs can be tuned in terms of porosity, crystallinity and electronic behaviour. Section II covers 'top down' techniques. These rely on breaking down of a layered precursor, in the graphene case usually natural crystals like graphite or artificially synthesized materials, such as highly oriented pyrolythic graphite, monolayers or few layers (FL) flakes. The main focus of this section is on various exfoliation techniques in a liquid media, either intercalation or liquid phase exfoliation (LPE). The choice of precursor, exfoliation method, medium as well as the control of parameters such as time or temperature are crucial. A definite choice of parameters and conditions yields a particular material with specific properties that makes it more suitable for a targeted application. We cover protocols for the graphitic precursors to graphene oxide (GO). This is an important material for a range of applications in biomedicine, energy storage, nanocomposites, etc. Hummers' and modified Hummers' methods are used to make GO that subsequently can be reduced to obtain reduced graphene oxide (RGO) with a variety of strategies. GO flakes are also employed to prepare three-dimensional (3d) low density structures, such as sponges, foams, hydro- or aerogels. The assembly of flakes into 3d structures can provide improved mechanical properties. Aerogels with a highly open structure, with interconnected hierarchical pores, can enhance the accessibility to the whole surface area, as relevant for a number of applications, such as energy storage. The main recipes to yield graphite intercalation compounds (GICs) are also discussed. GICs are suitable precursors for covalent functionalization of graphene, but can also be used for the synthesis of uncharged graphene in solution. Degradation of the molecules intercalated in GICs can be triggered by high temperature treatment or microwave irradiation, creating a gas pressure surge in graphite and exfoliation. Electrochemical exfoliation by applying a voltage in an electrolyte to a graphite electrode can be tuned by varying precursors, electrolytes and potential. Graphite electrodes can be either negatively or positively intercalated to obtain GICs that are subsequently exfoliated. We also discuss the materials that can be amenable to exfoliation, by employing a theoretical data-mining approach. The exfoliation of LMs usually results in a heterogeneous dispersion of flakes with different lateral size and thickness. This is a critical bottleneck for applications, and hinders the full exploitation of GRMs produced by solution processing. The establishment of procedures to control the morphological properties of exfoliated GRMs, which also need to be industrially scalable, is one of the key needs. Section III deals with the processing of flakes. (Ultra)centrifugation techniques have thus far been the most investigated to sort GRMs following ultrasonication, shear mixing, ball milling, microfluidization, and wet-jet milling. It allows sorting by size and thickness. Inks formulated from GRM dispersions can be printed using a number of processes, from inkjet to screen printing. Each technique has specific rheological requirements, as well as geometrical constraints. The solvent choice is critical, not only for the GRM stability, but also in terms of optimizing printing on different substrates, such as glass, Si, plastic, paper, etc, all with different surface energies. Chemical modifications of such substrates is also a key step. Sections IV-VII are devoted to the growth of GRMs on various substrates and their processing after growth to place them on the surface of choice for specific applications. The substrate for graphene growth is a key determinant of the nature and quality of the resultant film. The lattice mismatch between graphene and substrate influences the resulting crystallinity. Growth on insulators, such as SiO2, typically results in films with small crystallites, whereas growth on the close-packed surfaces of metals yields highly crystalline films. Section IV outlines the growth of graphene on SiC substrates. This satisfies the requirements for electronic applications, with well-defined graphene-substrate interface, low trapped impurities and no need for transfer. It also allows graphene structures and devices to be measured directly on the growth substrate. The flatness of the substrate results in graphene with minimal strain and ripples on large areas, allowing spectroscopies and surface science to be performed. We also discuss the surface engineering by intercalation of the resulting graphene, its integration with Si-wafers and the production of nanostructures with the desired shape, with no need for patterning. Section V deals with chemical vapour deposition (CVD) onto various transition metals and on insulators. Growth on Ni results in graphitized polycrystalline films. While the thickness of these films can be optimized by controlling the deposition parameters, such as the type of hydrocarbon precursor and temperature, it is difficult to attain single layer graphene (SLG) across large areas, owing to the simultaneous nucleation/growth and solution/precipitation mechanisms. The differing characteristics of polycrystalline Ni films facilitate the growth of graphitic layers at different rates, resulting in regions with differing numbers of graphitic layers. High-quality films can be grown on Cu. Cu is available in a variety of shapes and forms, such as foils, bulks, foams, thin films on other materials and powders, making it attractive for industrial production of large area graphene films. The push to use CVD graphene in applications has also triggered a research line for the direct growth on insulators. The quality of the resulting films is lower than possible to date on metals, but enough, in terms of transmittance and resistivity, for many applications as described in section V. Transfer technologies are the focus of section VI. CVD synthesis of graphene on metals and bottom up molecular approaches require SLG to be transferred to the final target substrates. To have technological impact, the advances in production of high-quality large-area CVD graphene must be commensurate with those on transfer and placement on the final substrates. This is a prerequisite for most applications, such as touch panels, anticorrosion coatings, transparent electrodes and gas sensors etc. New strategies have improved the transferred graphene quality, making CVD graphene a feasible option for CMOS foundries. Methods based on complete etching of the metal substrate in suitable etchants, typically iron chloride, ammonium persulfate, or hydrogen chloride although reliable, are time- and resourceconsuming, with damage to graphene and production of metal and etchant residues. Electrochemical delamination in a low-concentration aqueous solution is an alternative. In this case metallic substrates can be reused. Dry transfer is less detrimental for the SLG quality, enabling a deterministic transfer. There is a large range of layered materials (LMs) beyond graphite. Only few of them have been already exfoliated and fully characterized. Section VII deals with the growth of some of these materials. Amongst them, h-BN, transition metal tri- and di-chalcogenides are of paramount importance. The growth of h-BN is at present considered essential for the development of graphene in (opto) electronic applications, as h-BN is ideal as capping layer or substrate. The interesting optical and electronic properties of TMDs also require the development of scalable methods for their production. Large scale growth using chemical/physical vapour deposition or thermal assisted conversion has been thus far limited to a small set, such as h-BN or some TMDs. Heterostructures could also be directly grown