812 research outputs found

    FPGA-based Fused Smart Sensor for Real-Time Plant-Transpiration Dynamic Estimation

    Get PDF
    Plant transpiration is considered one of the most important physiological functions because it constitutes the plants evolving adaptation to exchange moisture with a dry atmosphere which can dehydrate or eventually kill the plant. Due to the importance of transpiration, accurate measurement methods are required; therefore, a smart sensor that fuses five primary sensors is proposed which can measure air temperature, leaf temperature, air relative humidity, plant out relative humidity and ambient light. A field programmable gate array based unit is used to perform signal processing algorithms as average decimation and infinite impulse response filters to the primary sensor readings in order to reduce the signal noise and improve its quality. Once the primary sensor readings are filtered, transpiration dynamics such as: transpiration, stomatal conductance, leaf-air-temperature-difference and vapor pressure deficit are calculated in real time by the smart sensor. This permits the user to observe different primary and calculated measurements at the same time and the relationship between these which is very useful in precision agriculture in the detection of abnormal conditions. Finally, transpiration related stress conditions can be detected in real time because of the use of online processing and embedded communications capabilities

    Thrombopoietin Receptor Agonists for Severe Thrombocytopenia after Allogeneic Stem Cell Transplantation : Experience of the Spanish Group of Hematopoietic Stem Cell Transplant

    Get PDF
    Persistent thrombocytopenia is a common complication after allogeneic hematopoietic stem cell transplantation (allo-SCT). Romiplostim and eltrombopag are the currently available thrombopoietin receptor agonists (TPO-RAs), and some studies with very small numbers of cases have reported their potential efficacy in the allo-SCT setting. The present retrospective study evaluated the safety and efficacy of TPO-RAs in 86 patients with persistent thrombocytopenia after allo-HSCT. Sixteen patients (19%) had isolated thrombocytopenia (PT), and 71 (82%) had secondary failure of platelet recovery (SFPR). TPO-RA therapy was started at a median of 127 days (range, 27 to 1177 days) after allo-SCT. The median initial and maximum administered doses were 50 mg/day (range, 25 to 150 mg/day) and 75 mg/day (range, 25 to 150 mg/day), respectively, for eltrombopag and 1 ”g/kg (range, 1 to 7 ”g/kg) and 5 ”g/kg (range, 1 to 10 ”g/kg), respectively, for romiplostin. The median platelet count before initiation of TPO-RA therapy was 14,000/”L (range, 1000 to 57,000/”L). Platelet recovery to ≄50,000/”L without transfusion support was achieved in 72% of patients at a median time of 66 days (range, 2 to 247 days). Eighty-one percent of the patients had a decreased number of megakaryocytes before treatment, showing a slower response to therapy (P =.011). The median duration of treatment was 62 days (range, 7 to 700 days). Grade 3-4 adverse events (hepatic and asthenia) were observed in only 2% of the patients. At last follow-up, 81% of patients had discontinued TPO-RAs and maintained response, and 71% were alive. To our knowledge, this is the largest series analyzing the use of TPO-RAs after allo-SCT reported to date. Our results support the efficacy and safety in this new setting. Further prospective trials are needed to increase the level of evidence and to identify predictors of response

    Production of He-4 and (4) in Pb-Pb collisions at root(NN)-N-S=2.76 TeV at the LHC

    Get PDF
    Results on the production of He-4 and (4) nuclei in Pb-Pb collisions at root(NN)-N-S = 2.76 TeV in the rapidity range vertical bar y vertical bar <1, using the ALICE detector, are presented in this paper. The rapidity densities corresponding to 0-10% central events are found to be dN/dy4(He) = (0.8 +/- 0.4 (stat) +/- 0.3 (syst)) x 10(-6) and dN/dy4 = (1.1 +/- 0.4 (stat) +/- 0.2 (syst)) x 10(-6), respectively. This is in agreement with the statistical thermal model expectation assuming the same chemical freeze-out temperature (T-chem = 156 MeV) as for light hadrons. The measured ratio of (4)/He-4 is 1.4 +/- 0.8 (stat) +/- 0.5 (syst). (C) 2018 Published by Elsevier B.V.Peer reviewe

    Reducing the environmental impact of surgery on a global scale: systematic review and co-prioritization with healthcare workers in 132 countries

    Get PDF
    Abstract Background Healthcare cannot achieve net-zero carbon without addressing operating theatres. The aim of this study was to prioritize feasible interventions to reduce the environmental impact of operating theatres. Methods This study adopted a four-phase Delphi consensus co-prioritization methodology. In phase 1, a systematic review of published interventions and global consultation of perioperative healthcare professionals were used to longlist interventions. In phase 2, iterative thematic analysis consolidated comparable interventions into a shortlist. In phase 3, the shortlist was co-prioritized based on patient and clinician views on acceptability, feasibility, and safety. In phase 4, ranked lists of interventions were presented by their relevance to high-income countries and low–middle-income countries. Results In phase 1, 43 interventions were identified, which had low uptake in practice according to 3042 professionals globally. In phase 2, a shortlist of 15 intervention domains was generated. In phase 3, interventions were deemed acceptable for more than 90 per cent of patients except for reducing general anaesthesia (84 per cent) and re-sterilization of ‘single-use’ consumables (86 per cent). In phase 4, the top three shortlisted interventions for high-income countries were: introducing recycling; reducing use of anaesthetic gases; and appropriate clinical waste processing. In phase 4, the top three shortlisted interventions for low–middle-income countries were: introducing reusable surgical devices; reducing use of consumables; and reducing the use of general anaesthesia. Conclusion This is a step toward environmentally sustainable operating environments with actionable interventions applicable to both high– and low–middle–income countries

    A Simple Methodology to Develop Bifilar, Quadrifilar, and Octofilar Calculable Resistors

    No full text
    This paper describes the development of bifilar, quadrifilar, and octofilar Calculable Resistors (CRs). The research involves Evanohm-S and Isaohm wire heat treatment processes to achieve temperature coefficients less than 0.5 &mu; &Omega; / &Omega; / ∘ C in the CR&rsquo;s wire resistance element, tests of different terminal&ndash;wire joining techniques, and construction aspects achieving a stability of less than 0.05 &mu; &Omega; / &Omega; /day. This kind of construction methodology has not been presented in detail in previous CR papers, and it is essential to accomplish the correct parameters of a CR. Without it, the development of a CR can take several months or even years. A comparison between CRs developed in this research and a CR from the Federal Institute of Metrology (METAS) in Switzerland was carried out. Measurement results between the 10 k &Omega; octofilar CR and the METAS 1 k &Omega; coaxial CR show an agreement better than 0.35 &mu; &Omega; / &Omega; through the audio-frequency range. Therefore, the octofilar CR can be used as an AC resistance reference with traceability to the quantum Hall resistance in DC

    FPGA-Based Smart Sensor for Drought Stress Detection in Tomato Plants Using Novel Physiological Variables and Discrete Wavelet Transform

    No full text
    Soil drought represents one of the most dangerous stresses for plants. It impacts the yield and quality of crops, and if it remains undetected for a long time, the entire crop could be lost. However, for some plants a certain amount of drought stress improves specific characteristics. In such cases, a device capable of detecting and quantifying the impact of drought stress in plants is desirable. This article focuses on testing if the monitoring of physiological process through a gas exchange methodology provides enough information to detect drought stress conditions in plants. The experiment consists of using a set of smart sensors based on Field Programmable Gate Arrays (FPGAs) to monitor a group of plants under controlled drought conditions. The main objective was to use different digital signal processing techniques such as the Discrete Wavelet Transform (DWT) to explore the response of plant physiological processes to drought. Also, an index-based methodology was utilized to compensate the spatial variation inside the greenhouse. As a result, differences between treatments were determined to be independent of climate variations inside the greenhouse. Finally, after using the DWT as digital filter, results demonstrated that the proposed system is capable to reject high frequency noise and to detect drought conditions

    Low Computational-Cost Footprint Deformities Diagnosis Sensor through Angles, Dimensions Analysis and Image Processing Techniques

    No full text
    Manual measurements of foot anthropometry can lead to errors since this task involves the experience of the specialist who performs them, resulting in different subjective measures from the same footprint. Moreover, some of the diagnoses that are given to classify a footprint deformity are based on a qualitative interpretation by the physician; there is no quantitative interpretation of the footprint. The importance of providing a correct and accurate diagnosis lies in the need to ensure that an appropriate treatment is provided for the improvement of the patient without risking his or her health. Therefore, this article presents a smart sensor that integrates the capture of the footprint, a low computational-cost analysis of the image and the interpretation of the results through a quantitative evaluation. The smart sensor implemented required the use of a camera (Logitech C920) connected to a Raspberry Pi 3, where a graphical interface was made for the capture and processing of the image, and it was adapted to a podoscope conventionally used by specialists such as orthopedist, physiotherapists and podiatrists. The footprint diagnosis smart sensor (FPDSS) has proven to be robust to different types of deformity, precise, sensitive and correlated in 0.99 with the measurements from the digitalized image of the ink mat

    Instrumentation in Developing Chlorophyll Fluorescence Biosensing: A Review

    Get PDF
    Chlorophyll fluorescence can be defined as the red and far-red light emitted by photosynthetic tissue when it is excited by a light source. This is an important phenomenon which permits investigators to obtain important information about the state of health of a photosynthetic sample. This article reviews the current state of the art knowledge regarding the design of new chlorophyll fluorescence sensing systems, providing appropriate information about processes, instrumentation and electronic devices. These types of systems and applications can be created to determine both comfort conditions and current problems within a given subject. The procedure to measure chlorophyll fluorescence is commonly split into two main parts; the first involves chlorophyll excitation, for which there are passive or active methods. The second part of the procedure is to closely measure the chlorophyll fluorescence response with specialized instrumentation systems. Such systems utilize several methods, each with different characteristics regarding to cost, resolution, ease of processing or portability. These methods for the most part include cameras, photodiodes and satellite images
    • 

    corecore