Effect of Temperature on Ausferritic Nodular Cast Iron Microstructure

The work presents the results of the studies of the effect of the temperature on the microstructure of ausferritic nodular cast iron. The ausferrite in the matrix was obtained by way of a specific combination of molybdenum and copper. The cast iron underwent annealing at the temperatures of 520, 550 and 580°C. The work presents the effect of the annealing temperature on the fraction of austenite in the cast iron matrix. The annealed and non-annealed cast iron hardness is given. The work also proves that an increase in the temperature up to 580°C causes a drop in the cast iron hardness

EFFECT OF ALUMINIUM AND MAGNESIUM ON THE CORROSION RESISTANCE OF ZINC COATINGS

This article presents the research on corrosion resistance of Zn-Al-Mg coatings with varying aluminium and magnesium content. Aluminium and magnesium were added directly to the zinc bath at 10:1 rate. There was found more than sixfold increase in corrosion resistance of zinc coatings with aluminium content at the level of 4% of weight and magnesium content at the level of 0.4% of weight. In contrast to the amounts applied in the literature, such content of these alloy additives in the zinc bath limits to a significant extent the amount of intermetallic phases in zinc coatings obtained from such baths. This, in consequence, results in high resistance to corrosion with simultaneous retention of high plasticity of these coatings

Ex Vivo Area-Metric Analysis of Root Canal Obturation Using Cold and Warm Gutta-Percha

properly cited. Purpose. To evaluate the percentage content of gutta-percha, sealer, and voids in a filled canal area following three different filling techniques, using microphotographs and Nis Elements5 software. Material and Methods. After completing chemomechanical preparation, the teeth ( = 48) were randomly divided into three groups ( = 16) and filled by either cold lateral condensation (CLC group), the continuous wave technique (EOU group), and the ProTaper5 thermoplasticized obturator (PT group). The roots were then sectioned horizontally 2.5, 6.5 and 8.5 mm from the tooth apical foramen. The surface areas of the sealer, voids, and guttapercha (PGFA percentage of gutta-percha-filled area) were calculated and the results subjected to statistical analysis (Kruskal-Wallis test). Results. The percentage of gutta-percha (PGFA) was lower in the apical third of the canal for the CLC and EOU groups than the PT group. In the middle and the coronal third of the canal, the PGFA value was higher after using thermal techniques (EOU and PT) than cold lateral condensation (CLC). The presence of voids was comparable in the fillings performed using warm and cold gutta-percha obturation at all levels. Conclusion. Although thermal methods of root canal obturation allow higher PGFA values to be obtained than cold lateral condensation, the content of voids is comparable

The pulp stones : morphological analysis in scanning electron microscopy and spectroscopic chemical quantification

Background and objectives: Pulp stones are hard tissue structures formed in the pulp of permanent and deciduous teeth. Few studies have evaluated their morphology and chemical composition. However, their formation, composition, configuration and role played in overall health status are still unclear. Clinically, they may be symptomatic; technically, they impede access during endodontic therapy, increasing the risk of treatment errors. Thus, this study aimed to morphologically analyze pulp stones and present their chemical quantification, identifying their main chemical elements. It also correlates the results with their possible induction mechanisms. Materials and Methods: Seven pulp nodules were collected from molar teeth needing endodontic treatment. The morphology of the stones was analyzed by scanning electron microscopy (SEM), and their chemical composition was determined by X-ray dispersive energy spectroscopy (EDX). Results: These structures varied considerably in shape, size and topography. The site of the stones in the pulp cavity was the factor that most affected the morphology. The majority of the stones found in the pulp chambers presented nodular morphology, while those in the root canals presented a diffuse shape, resembling root canal anatomy. The topography of the nodules showed heterogeneous relief, revealing smooth and compact areas contrasting with the rugged and porous ones. The chemical composition varied depending on the location of the nodule in the pulp cavity and the relief of the analyzed area. Radicular stones presented considerably lower calcium and phosphorus content than coronary nodules. Conclusions: The high cellularity rate of the coronal pulp predisposes this region to nodular mineralizations around injured cells. The presence of larger caliber vascular bundles and higher collagen fiber content in radicular pulp determines a diffuse morphological pattern in this region. Understanding the morphology and chemical composition of the pulp stones allows future translational pathways towards the prevention or treatment of such conditions

Search for dark matter produced in association with bottom or top quarks in √s = 13 TeV pp collisions with the ATLAS detector

A search for weakly interacting massive particle dark matter produced in association with bottom or top quarks is presented. Final states containing third-generation quarks and miss- ing transverse momentum are considered. The analysis uses 36.1 fb−1 of proton–proton collision data recorded by the ATLAS experiment at √s = 13 TeV in 2015 and 2016. No significant excess of events above the estimated backgrounds is observed. The results are in- terpreted in the framework of simplified models of spin-0 dark-matter mediators. For colour- neutral spin-0 mediators produced in association with top quarks and decaying into a pair of dark-matter particles, mediator masses below 50 GeV are excluded assuming a dark-matter candidate mass of 1 GeV and unitary couplings. For scalar and pseudoscalar mediators produced in association with bottom quarks, the search sets limits on the production cross- section of 300 times the predicted rate for mediators with masses between 10 and 50 GeV and assuming a dark-matter mass of 1 GeV and unitary coupling. Constraints on colour- charged scalar simplified models are also presented. Assuming a dark-matter particle mass of 35 GeV, mediator particles with mass below 1.1 TeV are excluded for couplings yielding a dark-matter relic density consistent with measurements