New developments with cold asphalt concrete binder course mixtures containing binary blended cementitious filler (BBCF)

A weakness in early strength and the need for longer curing times in the case of cold bituminous emulsion mixtures (CBEMs) compared to hot mix asphalt have been cited as barriers to the wider utilization of these mixtures. A binary blended filler material produced from high calcium fly ash (HCFA) and a fluid catalytic cracking catalyst (FC3R) was found to be very effective in providing microstructural integrity with a novel fast-curing cold asphalt concrete for the binder course (CACB) mixture. Balanced oxide compositions within the novel filler were identified as responsible for an enhanced hydration reaction, resulting in a very high early strength and a significant improvement in permanent deformation and fatigue resistance. Improved water sensitivity for progressive hydration with the new binary filler was also established while SEM analysis confirmed the formation of hydration products after various curing ages. © 2016 Elsevier Lt

A numerical investigation on the fire response of a steel girder bridge

The response of bridges subject to fire is an under researched topic despite the number of bridge failures caused by fire. Since available data shows that steel girder bridges are especially vulnerable to fire, this paper delves into their fire response by analyzing with a 3D numerical model the response of a typical bridge of 12.20 m span length. A parametric study is performed considering: (1) two possibilities for the axial restraint of the bridge deck, (2) four types of structural steel for the girders (carbon steel and stainless steel grades 1.4301, 1.4401, and 1.4462), (3) three different constitutive models for carbon steel, (4) four live loads, and (5) two alternative fire loads (the hydrocarbon fire defined by Eurocode 1 and a fire corresponding to a real fire event). Results show that restraint to deck expansion coming from an adjacent span or abutment should be considered in the numerical model. In addition, times to collapse are very small when the bridge girders are built with carbon steel (between 8.5 and 18 min) but they can almost double if stainless steel is used for the girders. Therefore, stainless steel is a material to consider for steel girder bridges in a high fire risk situation, especially if the bridge is located in a corrosive environment and its aesthetics deserves special attention. The methodology developed in this paper and the results obtained are useful for researchers and practitioners interested in developing and applying a performance-based approach for the design of bridges against fire. © 2012 Elsevier Ltd. All rights reserved.Funding for this research has been provided to Dr. Paya-Zaforteza by the Spanish Ministry of Education (contract number EX-2008-0669 of the Program for Postdoctoral Stays), the Spanish Ministry of Economy and Competitiveness (research project BIA 2011-27104) and the Universitat Politecnica de Valencia (Research and Development Support Program PAID-06-11). Funding has also been provided to Dr. Maria Garlock by the National Science Foundation (NSF) under award number CMMI-1068252. All opinions expressed in this paper are the authors' and do not necessarily reflect the policies and views of the sponsors.Paya-Zaforteza, I.; Garlock, ME. (2012). A numerical investigation on the fire response of a steel girder bridge. Journal of Constructional Steel Research. 75:93-103. https://doi.org/10.1016/j.jcsr.2012.03.012S931037

Influence of adding phase change materials on the physical and mechanical properties of cement mortars

During the last years several studies of construction materials with incorporation of encapsulated phase change material (PCM) have been published. However, the utilization of non-encapsulated PCM is one of the main gaps. The main objective of this work was the study of physical and mechanical properties of cement mortars with incorporation of non-encapsulated PCM. It was possible to conclude that the utilization of non-encapsulated phase change materials can be seen as a good and more economical solution for the energy efficiency of the buildings, without prejudice of the properties.The authors acknowledge the Portuguese Foundation for Science and Technology (FCT) for the financial support of PhD scholarship SFRH/BD/95611/2013

Strengths-Weaknesses-Opportunities-Threats analysis of carbon footprint indicator and derived recommendations

ABSTRACT: Demand for a low carbon footprint may be a key factor in stimulating innovation, while prompting politicians to promote sustainable consumption. However, the variety of methodological approaches and techniques used to quantify life-cycle emissions prevents their successful and widespread implementation. This study aims to offer recommendations for researchers, policymakers and practitioners seeking to achieve a more consistent approach for carbon footprint analysis. This assessment is made on the basis of a comprehensive Strengths-Weaknesses-Opportunities-Threats or SWOT Analysis of the carbon footprint indicator. It is carried out bringing together the collective experience from the Carbonfeel Project following the Delphi technique principles. The results include the detailed SWOT Analysis from which specific recommendations to cope with the threats and the weaknesses are identified. In particular, results highlight the importance of the integrated approach to combine organizational and product carbon footprinting in order to achieve a more standardized and consistent approach. These recommendations can therefore serve to pave the way for the development of new, specific and highly-detailed guidelines

Web crippling behaviour and design of aluminium lipped channel sections under two flange loading conditions

Aluminium alloys have recently drawn significant attention in structural applications due to its outstanding mechanical characteristics. Thin-walled members fabricated by aluminium alloys can be more competitive in construction industries than the conventional cold-formed steel sections, particularly in areas with high humidity and severe environmental conditions. Nevertheless, they are more vulnerable to various types of instability due to their relatively low elastic modulus compared to steel. Applying high concentrated load transversely on thin-walled members can cause critical damage to the web of the cross section called web crippling. Although a large number of studies has been performed to investigate the web crippling mechanisms on different types of sections, the existing studies are primarily of the empirical nature and thus merits further investigations. To fill the research gap, this study was thus performed based on our previously conducted experimental work to further comprehend the web crippling phenomenon of the roll-formed aluminium lipped channel (ALC) sections under the loading conditions of end-two-flange (ETF) and interior-two-flange (ITF). This was done through numerical investigations followed by a parametric study which are reported herein in details. A wide range of roll-formed ALC sections covering web slenderness ratios ranged from 28 to 130, inside bent radii ranging between 2 mm and 8 mm, bearing lengths ranged from 50 mm to 150 mm, and three sheeting aluminium alloy grades (5052-H32, 5052-H36 and 5052-H38) were considered in the parametric study. The acquired web crippling database was then used to assess the consistency and accuracy of the current design rules used in practice. It was found that the web crippling capacity determined by the current international specifications are unsafe and unreliable, whereas the predictions of the recently proposed equations agree very well. Furthermore, a Direct Strength Method (DSM)-based capacity prediction approach was proposed and then validated against the web crippling database acquired here as well as the experimental and numerical data for cold-formed steel lipped channel sections used in the literature