Stress Tuning of Laser Crystals

The topic of stress tunable laser crystals is addressed in this study with the purpose of determining the piezo-optic coefficients of a new laser material. This data was collected using a quadruple pass birefringence technique because of its high degree of sensitivity relative to the other methods examined including fringe shift analysis using a Mach-Zender interferometer. A green He-Ne laser was passed through a light chopper and Glan-Thompson prism before entering a crystal of Erbium doped Yttrium Aluminum Garnet (Er:YAG) (used in order to validate the experimental technique). The Er:YAG crystal is mounted in a press mechanism and the laser is quadruple passed through test specimen before being returned through the prism and the orthogonally polarized portion of the beam measured with a optical sensor. At a later stage, the Er:YAG crystal was replaced with a new crystal in order to determine the piezo-optic coefficients of this uncharacterized material. The applied load was monitored with the use of a 50 lb. load cell placed in line with the press. Light transmission readings were taken using a lock-in amplifier while load cell measurements were taken with a voltmeter from a 5 volt, 0.5 amp power supply. Despite the fact that an effective crystal press damping system was developed, size limitations precluded the use of the complete system. For this reason, data points were taken only once per full turn so as to minimize the effect of non uniform load application on the collected data. Good correlation was found in the transmission data between the experimentally determined Er:YAG and the previously known peizo-optic constants of non-doped crystal with which it was compared. The variation which was found between the two could be accounted for by the aforementioned presence of Erbium in the experimental sample (for which exact empirical data was not known). The same test procedure was then carried out on a Yttrium Gallium Aluminum garnet (YGAG) for the purpose of establishing values of its unknown piezo-optic constant tensor using experimentally collected transmission data. Significant variation between the piezo-optic constants of YAG and YGAG crystals was found however, the excellent data correlation of separate experimental runs carried out on the YGAG sample demonstrates the validity of these results. The data collected during the stressing of the YGAG was of high quality, however the amount of data collected was somewhat limited by a fracture of YGAG specimen which undoubted altered the crystalline lattice structure and hence precluded any further testing

Grampian migmatites in the Buchan Block, NE Scotland

Rocks exposed along the Scottish coast between Fraserburgh and Inzie Head contain information critical to understanding the evolution of the Buchan Block, the type locality for low-P, high-T regional metamorphism, and its relationship with the rest of the Grampian terrane, one of the major tectonostratigraphic components of the Scottish Caledonides. The ~8 km long section traverses a regional network of shear zones and, at the highest grades around Inzie Head, passes into the core of the Buchan Anticline, a large-scale open fold that is commonly regarded as a late structure, post-dating metamorphism. The metasedimentary rocks increase in grade from upper amphibolite to granulite facies and preserve unequivocal evidence for partial melting. The diatexite migmatites around Inzie Head, along with other gneissose units within the Buchan Block, have been regarded as allochthonous Precambrian basement rocks that were thrust into their current position during the Grampian orogenesis. However, field observations show that the onset of in situ partial melting in metapelitic rocks, which was associated with the formation of garnet-bearing aplites and associated pegmatites, occurred around Fraserburgh, where shear fabrics are absent.Thus, the rocks preserve a continuous metamorphic field gradient that straddles the shear zone network. This observation supports an alternative interpretation that anatexis was the result of mid-Ordovician (Grampian) metamorphism, rather than an older tectonothermal event, and that the Inzie Head gneisses are autochthonous. Using an average mid-Dalradian pelite as a plausible representative protolith, phase equilibria modelling satisfactorily reproduces the observed appearance and disappearance of key minerals providing that peritectic garnet produced with the first formed melts (represented by the garnet-bearing aplites) depleted the source rocks in Mn. The modelled metamorphic field gradient records a temperature increase of at least 150 °C (from ~650 °C near Fraserburgh to in excess of 800 °C at Inzie Head) but is isobaric at pressures of 2.7–2.8 kbar, suggesting the Buchan Anticline developed synchronous with partial melting. The Buchan Anticline is likely an expression of crustal thinning and asthenospheric upwelling, which produced voluminous gabbroic intrusions that supplied the heat for Buchan metamorphism

Development and Validation of a Supersonic Helium-Air Coannular Jet Facility

Data are acquired in a simple coannular He/air supersonic jet suitable for validation of CFD (Computational Fluid Dynamics) codes for high speed propulsion. Helium is employed as a non-reacting hydrogen fuel simulant, constituting the core of the coannular flow while the coflow is composed of air. The mixing layer interface between the two flows in the near field and the plume region which develops further downstream constitute the primary regions of interest, similar to those present in all hypersonic air breathing propulsion systems. A computational code has been implemented from the experiment's inception, serving as a tool for model design during the development phase