The potential of energy recovery from by–products of small agricultural farms in Nigeria

ArticleAgricultural by–products are renewable energy sources from which essential amount of energy can be recovered, which can be used to replace the use of conventional fossil fuel, reduces the potential of greenhouse gas (GHG) emission and at the same time reduces deforestation, especially in rural areas. Energy values of biomass from small Agricultural farms, in particular waste generated from different tropical crops, viz; Maize, Millet, Rice, Sorghum and Groundnut were determined, to ascertain their potentials as alternative fuel sources for rural use. The materials were found to be of importance judging by their combustion potentials in all the forms investigated. The Energy values of the by-products considered ranged between 11.68 MJkg-1 to 17.48 MJkg-1 with Groundnut pods and millet husk having the highest and least respectively. Moisture and ash had effect on the energy values of these biomass. Our results are relevant to the problems posed by the management of farm residues in developing countries

Energy consumption of milking pump controlled by frequency convertor during milking cycle

ArticleThe article deals with selected parameters affecting the energy consumption of a vacuum pump in a milking system during the whole milking cycle in variants with and without regulation by a frequency convertor. When put into practice, the latest research of creation, control and stabilization of vacuum in milking devices allows dairy farmers to obtain a vacuum system that ensures maximum stability of milking pressure, which is a basic requirement affecting the health of dairy cows. The choice of vacuum system prioritizes in particular high performance, maximum operational reliability, minimum maintenance, long service life, environmental friendliness and economy. The vacuum pump was a Roots vacuum pump with a rotary piston which is typical for this use. Use of a frequency convertor significantly affected the efficiency of this pump for control of vacuum pressure level and pump performance by varying the rotation frequency according to the actual airflow requirement. Using this control system, only as much vacuum pressure is produced as necessary. By measurement of an experimental setup, it was found that the average power requirement of a setup with a control valve was 3.8 kW compared to 1.7 kW in the case of the variant with frequency convertor. Measurements and calculations have shown that this system is capable of saving more than 50% of electric energy

Evaluation of dried compost for energy use via co-combustion with wood

ArticleThere is still a question of utilization of compost of unsatisfactory quality. This article deals with energy utilization of untreated compost. The energy utilization of raw compost as a fuel is not directly possible without further processing. Separation might be necessary due to large amount of mineral content (soils and other inert substances). This article is focused on the analysis of the basic fuel characteristics of compost. Proximate and elemental analyses were performed and stoichiometric combusti on was calculated. Finally, the sample was co - burned with wood biomass in a fixed grate combustion device and the gaseous emissions were determined in dependence on the amount of combustion air supplied. The emissions were expressed in graphs against exces s air coefficient and flue gas temperature. Elemental analysis of the compost sample shows high percentage of ash up to 61.70% wt. on dry basis causing low average calorific value of 8.51 MJ kg - 1 on dry basis. For combustion tests, the heating value was in creased by addition of wood chips to reach an average calorific value of the mixture to 13.4 MJ kg - 1 . The determined stoichiometric parameters can help in optimization of diffusion controlled combustion of composts or similar materials. In combustion of th e mixture of compost and wood biomass an optimum of emission parameters was found not exceeding the emission limits. Measured emission concentrations show the possibility of optimizing the combustion processes and temperatures while lowering CO emissions v ia the regulation of combustion air

THE CURRENT VIEW ON THE USE OF RECONSTRUCTION MATERIALS IN DENTISTRY

The hardest tissue in the human body is the enamel which covers the anatomical crowns of teeth. It must be resistant to mechanical stress and the chemical attack of many substances from food, drinks and products of the metabolism of bacteria present in the oral cavity. These low pH substances dissolve the mineral components of enamel, cause tooth demineralization, and lead to decay or erosion damage with the irreversible loss of dental hard tissues and the necessity of their reconstruction. The range of dental materials intended for dental tissue reconstruction is extensive. Dental amalgam can be mechanically applied into the strongly stressed lateral segments of teeth. The use of amalgam is, however, in decline, with the possible health risks attributed to it, coupled with the need to extensively prepare tooth tissue promoting a shift towards using aesthetically and biologically favourable dental ceramic and polymeric materials instead. Current developments also concentrate on these materials to reinforce this, with polymeric composite materials based on methacrylates with varying amounts of inorganic fillers at the forefront. These materials are distinguished by their good mechanical and aesthetic properties and wear resistance. However, polymerization shrinkage and a strong hydrophobic nature does not allow for their direct bonding to hard dental tissues. Risks associated with the release of residual free monomers from the structure to the environment, which may cause health complications, mainly allergic reactions in sensitive individuals, have been monitored recently. Further development in the field of composite materials aims to reduce or completely eliminate these negatives

Comparison of a 1 t and a 55 t container when storing spelt grain in mild climate of the Czech Republic

ArticleMaintaining a suitable microclimate inside the storage space is the most significant factor in maintaining good quality of stored grain for small farmers. This article is aimed at evaluating the influence of outdoor climatic conditions on the storage conditions, specifically the temperature of stored grain in two storage containers. One structure was a 4 × 6 m cylindrical container (55 t capacity) with a steel wire mesh wall lined with a textile shell. Spelt grain (Triticum spelta) was also stored simultaneously at the same location in a fabric intermediate bulk container (FIBC) bag with maximum capacity of 1 t. Neither structure was mechanically aerated. Grain moisture and temperature were monitored during the spring and start of the summer period of the year 2017 because of the biggest differences between the night and day temperatures. For monitoring of the grain microbiological changes samples were taken for laboratory tests during the whole experiment. Grain quality parameters measured during storage included the bulk density, crude protein, falling number, germination, gluten content, sedimentation index and contamination by mycotoxins. Monitored outdoor environment parameters were temperature, dew point and relative humidity. Results showed a strong dependence of the stored material temperature on the outside temperature in the case of FIBC bags (coefficient of determination R 2 = 0.927), whereas the dependence was weaker in the larger structure (R 2 = 0.625). Mycotoxins monitored during the period were below the detection limit in both cases

The Fourteenth Data Release of the Sloan Digital Sky Survey: First Spectroscopic Data from the extended Baryon Oscillation Spectroscopic Survey and from the second phase of the Apache Point Observatory Galactic Evolution Experiment

The fourth generation of the Sloan Digital Sky Survey (SDSS-IV) has been in operation since July 2014. This paper describes the second data release from this phase, and the fourteenth from SDSS overall (making this, Data Release Fourteen or DR14). This release makes public data taken by SDSS-IV in its first two years of operation (July 2014-2016). Like all previous SDSS releases, DR14 is cumulative, including the most recent reductions and calibrations of all data taken by SDSS since the first phase began operations in 2000. New in DR14 is the first public release of data from the extended Baryon Oscillation Spectroscopic Survey (eBOSS); the first data from the second phase of the Apache Point Observatory (APO) Galactic Evolution Experiment (APOGEE-2), including stellar parameter estimates from an innovative data driven machine learning algorithm known as "The Cannon"; and almost twice as many data cubes from the Mapping Nearby Galaxies at APO (MaNGA) survey as were in the previous release (N = 2812 in total). This paper describes the location and format of the publicly available data from SDSS-IV surveys. We provide references to the important technical papers describing how these data have been taken (both targeting and observation details) and processed for scientific use. The SDSS website (www.sdss.org) has been updated for this release, and provides links to data downloads, as well as tutorials and examples of data use. SDSS-IV is planning to continue to collect astronomical data until 2020, and will be followed by SDSS-V.Comment: SDSS-IV collaboration alphabetical author data release paper. DR14 happened on 31st July 2017. 19 pages, 5 figures. Accepted by ApJS on 28th Nov 2017 (this is the "post-print" and "post-proofs" version; minor corrections only from v1, and most of errors found in proofs corrected

The Fourteenth Data Release of the Sloan Digital Sky Survey: First Spectroscopic Data from the Extended Baryon Oscillation Spectroscopic Survey and from the Second Phase of the Apache Point Observatory Galactic Evolution Experiment

The fourth generation of the Sloan Digital Sky Survey (SDSS-IV) has been in operation since 2014 July. This paper describes the second data release from this phase, and the 14th from SDSS overall (making this Data Release Fourteen or DR14). This release makes the data taken by SDSS-IV in its first two years of operation (2014–2016 July) public. Like all previous SDSS releases, DR14 is cumulative, including the most recent reductions and calibrations of all data taken by SDSS since the first phase began operations in 2000. New in DR14 is the first public release of data from the extended Baryon Oscillation Spectroscopic Survey; the first data from the second phase of the Apache Point Observatory (APO) Galactic Evolution Experiment (APOGEE-2), including stellar parameter estimates from an innovative data-driven machine-learning algorithm known as "The Cannon"; and almost twice as many data cubes from the Mapping Nearby Galaxies at APO (MaNGA) survey as were in the previous release (N = 2812 in total). This paper describes the location and format of the publicly available data from the SDSS-IV surveys. We provide references to the important technical papers describing how these data have been taken (both targeting and observation details) and processed for scientific use. The SDSS web site (www.sdss.org) has been updated for this release and provides links to data downloads, as well as tutorials and examples of data use. SDSS-IV is planning to continue to collect astronomical data until 2020 and will be followed by SDSS-V