110 research outputs found
The European Spallation Source neutrino super-beam conceptual design report
Artículo escrito por un elevado número de autores, solo se referencian el que aparece en primer lugar, el nombre del grupo de colaboración, si le hubiere, y los autores pertenecientes a la UAMA design study, named ESS νSB for European Spallation Source neutrino Super Beam, has been carried out during the years 2018–2022 of how the 5 MW proton linear accelerator of the European Spallation Source under construction in Lund, Sweden, can be used to produce the world’s most intense long-baseline neutrino beam. The high beam intensity will allow for measuring the neutrino oscillations near the second oscillation maximum at which the CP violation signal is close to three times higher than at the first maximum, where other experiments measure. This will enable CP violation discovery in the leptonic sector for a wider range of values of the CP violating phase δCP and, in particular, a higher precision measurement of δCP. The present Conceptual Design Report describes the results of the design study of the required upgrade of the ESS linac, of the accumulator ring used to compress the linac pulses from 2.86 ms to 1.2 μs, and of the target station, where the 5 MW proton beam is used to produce the intense neutrino beam. It also presents the design of the near detector, which is used to monitor the neutrino beam as well as to measure neutrino cross sections, and of the large underground far detector located 360 km from ESS, where the magnitude of the oscillation appearance of νe from νμ is measured. The physics performance of the ESS νSB research facility has been evaluated demonstrating that after 10 years of data-taking, leptonic CP violation can be detected with more than 5 standard deviation significance over 70% of the range of values that the CP violation phase angle δCP can take and that δCP can be measured with a standard error less than 8° irrespective of the measured value of δCP. These results demonstrate the uniquely high physics performance of the proposed ESS νSB research facilit
The ESSnuSB design study: overview and future prospects
Artículo escrito por un elevado número de autores, solo se referencian el que aparece en primer lugar, los autores pertenecientes a la UAM y el nombre del grupo de colaboración, si lo hubiereESSnuSB is a design study for an experiment to measure the CP violation in the leptonic sector at the second neutrino oscillation maximum using a neutrino beam driven by the uniquely powerful ESS linear accelerator. The reduced impact of systematic errors on sensitivity at the second maximum allows for a very precise measurement of the CP violating parameter. This review describes the fundamental advantages of measurement at the second maximum, the necessary upgrades to the ESS linac in order to produce a neutrino beam, the near and far detector complexes, and the expected physics reach of the proposed ESSnuSB experiment, concluding with the near future developments aimed at the project realizationThis project has been supported by the COST Action EuroNuNet: “Combining forces for a novel European facility for neutrino-antineutrino symmetry-violation discovery”. It has also received funding from the European Union’s Horizon 2020 research and innovation programme under grant agreement No. 777419. We acknowledge further support provided by the following research funding agencies: Centre National de la Recherche Scientifique and Institut National de Physique Nucléaire et de Physique des Particules, France; Deutsche Forschungsgemeinschaft, Germany, Projektnummer 423761110; Agencia Estatal de Investigacion through the grants IFT Centro de Excelencia Severo Ochoa, Spain, contract No. CEX2020-001007-S and PID2019-108892RB funded by MCIN/AEI/10.13039/501100011033; Polish Ministry of Science and Higher Education, grant No. W129/H2020/2018, with the science resources for the years 2018–2021 for the realisation of a cofunded project; Ministry of Science and Education of Republic of Croatia grant No. KK.01.1.1.01.0001; Çukurova University Scientific Research Projects Unit, Grant no: FUA-2021-12628; as well as support provided by the universities and laboratories to which the authors of this report are affiliated, see the author list on the first page. Funded by the European Union. Views and opinions expressed are however those of the author(s) only and do not necessarily reflect those of the European Union. Neither the European Union nor the granting authority can be held responsible for the
Novel Double Triple Bend Achromat (DTBA) lattice design for a next generation 3 GeV Synchrotron Light Source
The Double Triple Bend Achromat (DTBA) lattice~\cite{DTBAipac16} is a novel
lattice design for a next generation 3 GeV Synchrotron Light Source. Starting
from a modification of the Hybrid Multi Bend Achromat (HMBA)
lattice~\cite{ESRF} developed at ESRF and inspired by the Double-Double Bend
Achromat (DDBA) lattice~\cite{Diamond1, Diamond2} developed at Diamond, DTBA
combines the advantages of both cells. The typical MBA lattice cells have one
straight section dedicated to an insertion device, whereas this new cell layout
has two such drifts, thus increasing the fraction of available space for the
installation of insertion devices. The DTBA lattice achieves an emittance of
, a dynamic aperture of
(calculated at the injection point), an injection efficiency of
and a lifetime of with
errors. The characteristics of DTBA, the methodology and results of the linear
and non-linear optics optimisations, with and without the presence of errors,
are presented in detail
Accelerator system for the PRISM based muon to electron conversion experiment
The next generation of lepton flavor violation experiments need high
intensity and high quality muon beams. Production of such beams requires
sending a short, high intensity proton pulse to the pion production target,
capturing pions and collecting the resulting muons in the large acceptance
transport system. The substantial increase of beam quality can be obtained by
applying the RF phase rotation on the muon beam in the dedicated FFAG ring,
which was proposed for the PRISM project.This allows to reduce the momentum
spread of the beam and to purify from the unwanted components like pions or
secondary protons. A PRISM Task Force is addressing the accelerator and
detector issues that need to be solved in order to realize the PRISM
experiment. The parameters of the required proton beam, the principles of the
PRISM experiment and the baseline FFAG design are introduced. The spectrum of
alternative designs for the PRISM FFAG ring are shown. Progress on ring main
systems like injection and RF are presented. The current status of the study
and its future directions are discussed.Comment: Studies performed within the PRISM Task Force initiativ
The LBNO long-baseline oscillation sensitivities with two conventional neutrino beams at different baselines
The proposed Long Baseline Neutrino Observatory (LBNO) initially consists of
kton liquid double phase TPC complemented by a magnetised iron
calorimeter, to be installed at the Pyh\"asalmi mine, at a distance of 2300 km
from CERN. The conventional neutrino beam is produced by 400 GeV protons
accelerated at the SPS accelerator delivering 700 kW of power. The long
baseline provides a unique opportunity to study neutrino flavour oscillations
over their 1st and 2nd oscillation maxima exploring the behaviour, and
distinguishing effects arising from and matter. In this paper we
show how this comprehensive physics case can be further enhanced and
complemented if a neutrino beam produced at the Protvino IHEP accelerator
complex, at a distance of 1160 km, and with modest power of 450 kW is aimed
towards the same far detectors. We show that the coupling of two independent
sub-MW conventional neutrino and antineutrino beams at different baselines from
CERN and Protvino will allow to measure CP violation in the leptonic sector at
a confidence level of at least for 50\% of the true values of
with a 20 kton detector. With a far detector of 70 kton, the
combination allows a sensitivity for 75\% of the true values of
after 10 years of running. Running two independent neutrino
beams, each at a power below 1 MW, is more within today's state of the art than
the long-term operation of a new single high-energy multi-MW facility, which
has several technical challenges and will likely require a learning curve.Comment: 21 pages, 12 figure
High intensity neutrino oscillation facilities in Europe
The EUROnu project has studied three possible options for future, high intensity neutrino oscillation facilities in Europe. The first is a Super Beam, in which the neutrinos come from the decay of pions created by bombarding targets with a 4 MW proton beam from the CERN High Power Superconducting Proton Linac. The far detector for this facility is the 500 kt MEMPHYS water Cherenkov, located in the Fréjus tunnel. The second facility is the Neutrino Factory, in which the neutrinos come from the decay of μ+ and μ− beams in a storage ring. The far detector in this case is a 100 kt magnetized iron neutrino detector at a baseline of 2000 km. The third option is a Beta Beam, in which the neutrinos come from the decay of beta emitting isotopes, in particular He6 and Ne18, also stored in a ring. The far detector is also the MEMPHYS detector in the Fréjus tunnel. EUROnu has undertaken conceptual designs of these facilities and studied the performance of the detectors. Based on this, it has determined the physics reach of each facility, in particular for the measurement of CP violation in the lepton sector, and estimated the cost of construction. These have demonstrated that the best facility to build is the Neutrino Factory. However, if a powerful proton driver is constructed for another purpose or if the MEMPHYS detector is built for astroparticle physics, the Super Beam also becomes very attractive
Characterisation of the muon beams for the Muon Ionisation Cooling Experiment
A novel single-particle technique to measure emittance has been developed and used to characterise seventeen different muon beams for the Muon Ionisation Cooling Experiment (MICE). The muon beams, whose mean momenta vary from 171 to 281 MeV/c, have emittances of approximately 1.2–2.3 π mm-rad horizontally and 0.6–1.0 π mm-rad vertically, a horizontal dispersion of 90–190 mm and momentum spreads of about 25 MeV/c. There is reasonable agreement between the measured parameters of the beams and the results of simulations. The beams are found to meet the requirements of MICE
Prediction of Beam Losses during Crab Cavity Quenches at the High Luminosity LHC
Studies of the crab cavities at KEKB revealed that the RF phase could shift by up to 50o within ~50 μs during a quench; while the cavity voltage is still at approximately 75% of its nominal amplitude. If such a failure were to occur on the HL-LHC crab cavities, it is likely that the machine would sustain substantial damage to the beam line and surrounding infrastructure due to uncontrolled beam loss before the machine protection system could dump the beam. We have developed a low-level RF system model, including detuning mechanisms and beam loading, and use this to simulate the behaviour of a crab cavity during a quench, modeling the low-level RF system, detuning mechanisms and beam loading. We supplement this with measurement data of the actual RF response of the proof of principle Double-Quarter Wave Crab Cravity during a quench. Extrapolating these measurements to the HL-LHC, we show that Lorentz Force detuning is the dominant effect leading to phase shifts in the crab cavity during quenches; rather than pressure detuning which is expected to be dominant for the KEKB crab cavities. The total frequency shift for the HL-LHC crab cavities during quenches is expected to be about 460 Hz, leading to a phase shift of no more than 3o. The results of the quench model are read into a particle tracking simulation, SixTrack, and used to determine the effect of quenches on the HL-LHC beam. The quench model has been benchmarked against the KEKB experimental measurements. In this paper we present the results of the simulations on a crab cavity failure for HL-LHC as well as for the SPS and show that beam loss is negligible when using a realistic low-level RF response
Interim Design Report
The International Design Study for the Neutrino Factory (the IDS-NF) was
established by the community at the ninth "International Workshop on Neutrino
Factories, super-beams, and beta- beams" which was held in Okayama in August
2007. The IDS-NF mandate is to deliver the Reference Design Report (RDR) for
the facility on the timescale of 2012/13. In addition, the mandate for the
study [3] requires an Interim Design Report to be delivered midway through the
project as a step on the way to the RDR. This document, the IDR, has two
functions: it marks the point in the IDS-NF at which the emphasis turns to the
engineering studies required to deliver the RDR and it documents baseline
concepts for the accelerator complex, the neutrino detectors, and the
instrumentation systems. The IDS-NF is, in essence, a site-independent study.
Example sites, CERN, FNAL, and RAL, have been identified to allow site-specific
issues to be addressed in the cost analysis that will be presented in the RDR.
The choice of example sites should not be interpreted as implying a preferred
choice of site for the facility
High-Luminosity Large Hadron Collider (HL-LHC): Technical Design Report
The Large Hadron Collider (LHC) is one of the largest scientific instruments ever built. Since opening up a new energy frontier for exploration in 2010, it has gathered a global user community of about 9000 scientists working in fundamental particle physics and the physics of hadronic matter at extreme temperature and density. To sustain and extend its discovery potential, the LHC will need a major upgrade in the 2020s. This will increase its instantaneous luminosity (rate of collisions) by a factor of five beyond the original design value and the integrated luminosity (total number of collisions) by a factor ten. The LHC is already a highly complex and exquisitely optimised machine so this upgrade must be carefully conceived and will require new infrastructures (underground and on surface) and over a decade to implement. The new configuration, known as High Luminosity LHC (HL-LHC), relies on a number of key innovations that push accelerator technology beyond its present limits. Among these are cutting-edge 11–12 Tesla superconducting magnets, compact superconducting cavities for beam rotation with ultra-precise phase control, new technology and physical processes for beam collimation and 100 metre-long high-power superconducting links with negligible energy dissipation, all of which required several years of dedicated R&D effort on a global international level.
The present document describes the technologies and components that will be used to realise the project and is intended to serve as the basis for the detailed engineering design of the HL-LHC
- …