Investigation into yield and reliability enhancement of TSV-based three-dimensional integration circuits

Three dimensional integrated circuits (3D ICs) have been acknowledged as a promising technology to overcome the interconnect delay bottleneck brought by continuous CMOS scaling. Recent research shows that through-silicon-vias (TSVs), which act as vertical links between layers, pose yield and reliability challenges for 3D design. This thesis presents three original contributions.The first contribution presents a grouping-based technique to improve the yield of 3D ICs under manufacturing TSV defects, where regular and redundant TSVs are partitioned into groups. In each group, signals can select good TSVs using rerouting multiplexers avoiding defective TSVs. Grouping ratio (regular to redundant TSVs in one group) has an impact on yield and hardware overhead. Mathematical probabilistic models are presented for yield analysis under the influence of independent and clustering defect distributions. Simulation results using MATLAB show that for a given number of TSVs and TSV failure rate, careful selection of grouping ratio results in achieving 100% yield at minimal hardware cost (number of multiplexers and redundant TSVs) in comparison to a design that does not exploit TSV grouping ratios. The second contribution presents an efficient online fault tolerance technique based on redundant TSVs, to detect TSV manufacturing defects and address thermal-induced reliability issue. The proposed technique accounts for both fault detection and recovery in the presence of three TSV defects: voids, delamination between TSV and landing pad, and TSV short-to-substrate. Simulations using HSPICE and ModelSim are carried out to validate fault detection and recovery. Results show that regular and redundant TSVs can be divided into groups to minimise area overhead without affecting the fault tolerance capability of the technique. Synthesis results using 130-nm design library show that 100% repair capability can be achieved with low area overhead (4% for the best case). The last contribution proposes a technique with joint consideration of temperature mitigation and fault tolerance without introducing additional redundant TSVs. This is achieved by reusing spare TSVs that are frequently deployed for improving yield and reliability in 3D ICs. The proposed technique consists of two steps: TSV determination step, which is for achieving optimal partition between regular and spare TSVs into groups; The second step is TSV placement, where temperature mitigation is targeted while optimizing total wirelength and routing difference. Simulation results show that using the proposed technique, 100% repair capability is achieved across all (five) benchmarks with an average temperature reduction of 75.2? (34.1%) (best case is 99.8? (58.5%)), while increasing wirelength by a small amount

A survey of carbon nanotube interconnects for energy efficient integrated circuits

This article is a review of the state-of-art carbon nanotube interconnects for Silicon application with respect to the recent literature. Amongst all the research on carbon nanotube interconnects, those discussed here cover 1) challenges with current copper interconnects, 2) process & growth of carbon nanotube interconnects compatible with back-end-of-line integration, and 3) modeling and simulation for circuit-level benchmarking and performance prediction. The focus is on the evolution of carbon nanotube interconnects from the process, theoretical modeling, and experimental characterization to on-chip interconnect applications. We provide an overview of the current advancements on carbon nanotube interconnects and also regarding the prospects for designing energy efficient integrated circuits. Each selected category is presented in an accessible manner aiming to serve as a survey and informative cornerstone on carbon nanotube interconnects relevant to students and scientists belonging to a range of fields from physics, processing to circuit design

A review of advances in pixel detectors for experiments with high rate and radiation

The Large Hadron Collider (LHC) experiments ATLAS and CMS have established hybrid pixel detectors as the instrument of choice for particle tracking and vertexing in high rate and radiation environments, as they operate close to the LHC interaction points. With the High Luminosity-LHC upgrade now in sight, for which the tracking detectors will be completely replaced, new generations of pixel detectors are being devised. They have to address enormous challenges in terms of data throughput and radiation levels, ionizing and non-ionizing, that harm the sensing and readout parts of pixel detectors alike. Advances in microelectronics and microprocessing technologies now enable large scale detector designs with unprecedented performance in measurement precision (space and time), radiation hard sensors and readout chips, hybridization techniques, lightweight supports, and fully monolithic approaches to meet these challenges. This paper reviews the world-wide effort on these developments.Comment: 84 pages with 46 figures. Review article.For submission to Rep. Prog. Phy

Thermo-Mechanical Effects Of Thermal Cycled Copper Through Silicon Vias

The semiconductor industry is currently facing transistor scaling issues due to fabrication thresholds and quantum effects. In this \u27More-Than-Moore\u27 era, the industry is developing new ways to increase device performance, such as stacking chips for three-dimensional integrated circuits (3D-IC). The 3D-IC\u27s superior performance over their 2D counterparts can be attributed to the use of vertical interconnects, or through silicon vias (TSV). These interconnects are much shorter, reducing signal delay. However TSVs are susceptible to various thermo-mechanical reliability concerns. Heating during fabrication and use, in conjunction with coefficient of thermal expansion mismatch between the copper TSVs and silicon substrate, create harmful stresses in the system. The purpose of this work is to evaluate the signal integrity of Cu-TSVs and determine the major contributing factors of the signal degradation upon in-use conditions. Two series of samples containing blind Cu-TSVs embedded in a Si substrate were studied, each having different types and amounts of voids from manufacturing. The samples were thermally cycled up to 2000 times using three maximum temperatures to simulate three unique in-use conditions. S11 parameter measurements were then conducted to determine the signal integrity of the TSVs. To investigate the internal response from cycling, a protocol was developed for cross-sectioning the copper TSVs. Voids were measured using scanning electron microscope and focused ion beam imaging of the cross-sections, while the microstructural evolution of the copper was monitored with electron backscattering diffraction. An increase in void area was found to occur after cycling. This is thought to be the major contributing factor in the signal degradation of the TSVs, since no microstructural changes were observed in the copper

Through Silicon Via Field-Effect Transistor with Hafnia-based Ferroelectrics and the Doping of Silicon by Gallium Implantation Utilizing a Focused Ion Beam System

3-dimensional integration has become a standard to further increase the transistor density and to enhance the integrated functionality in microchips. Integrated circuits are stacked on top of each other and copper-filled through-silicon VIAs (TSVs) are the industry-accepted choice for their vertical electrical connection. The aim of this work is to functionalize the TSVs by implementing vertical field-effect transistors inside the via holes. The front and back sides of 200 ... 300 µm thin silicon wafers were doped to create the source/drain regions of n- and p-FETs. The TSVFETs showed very stable saturation currents and on/off current ratios of about 10^6 (n-TSVFET) and 10^3 (p-TSVFET) for a gate voltage magnitude of 4V. The use of hafnium zirconium oxide on a thin SiO_2 interface layer as gate dielectric material in a p-TSVFET, enabled the implementation of a charge trapping memory inside the TSVs, showing a memory window of about 1V. This allows the non-volatile storage of the transistor on/off state. In addition, the demonstration of the use of gallium as the source/drain dopant in planar p-FET test structures (ion implanted from a focused ion beam tool) paves the way for maskless doping and for a process flow with a low thermal budget. It was shown, that ion implanted gallium can be activated and annealed at relatively low temperatures of 500 °C ... 700 °C.:Abstract / Kurzzusammenfassung Danksagung Index I List of Figures III List of Tables X List of Symbols XI List of Abbreviations XV 1 Introduction 1 2 Fundamentals 5 2.1 Metal Oxide Semiconductor Field Effect Transistors (MOSFETs) 5 2.1.1 Historical Development - Technological Advancements 7 2.1.2 Field-Effect Transistors in Semiconductor Memories 10 2.2 3D Integration and the Use of TSVs (Through Silicon VIAs) 16 2.3 Doping of Silicon 19 2.3.1 Doping by Thermal Diffusion 20 2.3.2 Doping by Ion Implantation 22 3 Electrical Characterization 24 3.1 Resistivity Measurements 24 3.1.1 Resistance Determination by Four-Point Probes Measurement 24 3.1.2 Contact Resistivity 27 3.1.3 Doping Concentration 32 3.2 C-V Measurements 35 3.2.1 Fundamentals of MIS C-V Measurements 35 3.2.2 Interpretation of C-V Measurements 37 3.3 Transistor Measurements 41 3.3.1 Output Characteristics (I_D-V_D) 41 3.3.2 Transfer Characteristics (I_D-V_G) 42 4 TSV Transistor 45 4.1 Idea and Motivation 45 4.2 Design and Layout of the TSV Transistor 47 4.2.1 Design of the TSV Transistor Structures 47 4.2.2 Test Structures for Planar FETs 48 5 Variations in the Integration Scheme of the TSV Transistor 51 5.1 Doping by Diffusion from Thin Films 51 5.1.1 Determination of Doping Profiles 52 5.1.2 n- and p- TSVFETs Doped Manufactures by the Use of the Diffusion Technique 59 5.2 Ferroelectric Hafnium-Zirconium-Oxide (HZO) in the Gate Stack 81 5.2.1 Planar ferroelectric p-MOSFETs Doped by Thermal Diffusion 82 5.2.2 p-TSVFETs with Hafnium-Zirconium-Oxide Metal Gate 90 5.3 Doping by Ion Implantation of Gallium with a Focused Ion Beam (FIB) Tool 96 5.3.1 Ga doped Si Diodes 97 5.3.2 Planar p-MOSFETs Doped by Ga Implantation 108 5.3.3 Proposal for a parallel integration of Cu TSVs and p-TSVFETs 117 6 Summary and Outlook 120 Bibliography XVIII A Appendix XXXVI A.1 Resistivity and Dopant Density XXXVI A.2 Mask set for the TSVFET XXXVII A.3 Mask Design of the Planar Test Structures XXXVIII Curriculum Vitae XXXIX List of Scientific Publications XL

High-Density Solid-State Memory Devices and Technologies

This Special Issue aims to examine high-density solid-state memory devices and technologies from various standpoints in an attempt to foster their continuous success in the future. Considering that broadening of the range of applications will likely offer different types of solid-state memories their chance in the spotlight, the Special Issue is not focused on a specific storage solution but rather embraces all the most relevant solid-state memory devices and technologies currently on stage. Even the subjects dealt with in this Special Issue are widespread, ranging from process and design issues/innovations to the experimental and theoretical analysis of the operation and from the performance and reliability of memory devices and arrays to the exploitation of solid-state memories to pursue new computing paradigms

A Cost-Effective Fault Tolerance Technique for Functional TSV in 3-D ICs

Regular and redundant through-silicon via (TSV) interconnects are used in fault tolerance techniques of 3-D IC. However, the fabrication process of TSVs results in defects that reduce the yield and reliability of TSVs. On the other hand, each TSV is associated with a significant amount of on-chip area overhead. Therefore, unlike the state-of-the-art fault tolerance architectures, here we propose the time division multiplexing access (TDMA)-based fault tolerance technique without using any redundant TSVs, which reduces the area overhead and enhances the yield. In the proposed technique, by means of TDMA, we reroute the signal through defect-free TSV. Subsequently, an architecture based on the proposed technique has been designed, evaluated, and validated on logic-on-logic 3-D IWLS'05 benchmark circuits using 130-nm technology node. The proposed technique is found to reduce the area overhead by 28.70%-40.60%, compared to the state-of-the-art architectures and results in a yield of 98.9%-99.8%

Addressing Manufacturing Challenges in NoC-based ULSI Designs

Hernández Luz, C. (2012). Addressing Manufacturing Challenges in NoC-based ULSI Designs [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/1669

High Speed Test Interface Module Using MEMS Technology

With the transient frequency of available CMOS technologies exceeding hundreds of gigahertz and the increasing complexity of Integrated Circuit (IC) designs, it is now apparent that the architecture of current testers needs to be greatly improved to keep up with the formidable challenges ahead. Test requirements for modern integrated circuits are becoming more stringent, complex and costly. These requirements include an increasing number of test channels, higher test-speeds and enhanced measurement accuracy and resolution. In a conventional test configuration, the signal path from Automatic Test Equipment (ATE) to the Device-Under-Test (DUT) includes long traces of wires. At frequencies above a few gigahertz, testing integrated circuits becomes a challenging task. The effects on transmission lines become critical requiring impedance matching to minimize signal reflection. AC resistance due to the skin effect and electromagnetic coupling caused by radiation can also become important factors affecting the test results. In the design of a Device Interface Board (DIB), the greater the physical separation of the DUT and the ATE pin electronics, the greater the distortion and signal degradation. In this work, a new Test Interface Module (TIM) based on MEMS technology is proposed to reduce the distance between the tester and device-under-test by orders of magnitude. The proposed solution increases the bandwidth of test channels and reduces the undesired effects of transmission lines on the test results. The MEMS test interface includes a fixed socket and a removable socket. The removable socket incorporates MEMS contact springs to provide temporary with the DUT pads and the fixed socket contains a bed of micro-pins to establish electrical connections with the ATE pin electronics. The MEMS based contact springs have been modified to implement a high-density wafer level test probes for Through Silicon Vias (TSVs) in three dimensional integrated circuits (3D-IC). Prototypes have been fabricated using Silicon On Insulator SOI wafer. Experimental results indicate that the proposed architectures can operate up to 50 GHz without much loss or distortion. The MEMS probes can also maintain a good elastic performance without any damage or deformation in the test phase

Heterogeneous 2.5D integration on through silicon interposer

© 2015 AIP Publishing LLC. Driven by the need to reduce the power consumption of mobile devices, and servers/data centers, and yet continue to deliver improved performance and experience by the end consumer of digital data, the semiconductor industry is looking for new technologies for manufacturing integrated circuits (ICs). In this quest, power consumed in transferring data over copper interconnects is a sizeable portion that needs to be addressed now and continuing over the next few decades. 2.5D Through-Si-Interposer (TSI) is a strong candidate to deliver improved performance while consuming lower power than in previous generations of servers/data centers and mobile devices. These low-power/high-performance advantages are realized through achievement of high interconnect densities on the TSI (higher than ever seen on Printed Circuit Boards (PCBs) or organic substrates), and enabling heterogeneous integration on the TSI platform where individual ICs are assembled at close proximity