펄스 기반 피드 포워드 이퀄라이저를 갖춘 고용량 DRAM을 위한 컨트롤러 PHY 설계

학위논문 (박사) -- 서울대학교 대학원 : 공과대학 전기·정보공학부, 2020. 8. 김수환.A controller PHY for managed DRAM solution, which is a new memory structure to maximize capacity while minimizing refresh power, is presented. Inter-symbol interference is critical in such a high-capacity DRAM interface in which many DRAM chips share a command/address (C/A) channel. A pulse-based feed-forward equalizer (PB-FFE) is introduced to reduce ISI on a C/A channel. The controller PHY supports all the training sequences specified in the DDR4 standard. A glitch-free DCDL is also adopted to perform link training efficiently and to reduce training time. The DQ transmitter adopts quarter-rate architecture to reduce output latency. For the quarter-rate transmitters in DQ, we propose a quadrature error corrector (QEC), in which clock signal phase errors are corrected using two replicas of the 4:1 serializer of the output stage. Pulse shrinking is used to compare and equalize the outputs of these two replica serializers. A controller PHY was fabricated in 55nm CMOS. The PB-FFE increases the timing margin from 0.23UI to 0.29UI at 1067Mbps. At 2133Mbps, the read timing and voltage margins are 0.53UI and 211mV after read training, and the write margins are 0.72UI and 230mV after write training. To validate the QEC effectiveness, a prototype quarter-rate transmitter, including the QEC, was fabricated to another chip in 65nm CMOS. Adopting our QEC, the experimental results show that the output phase errors of the transmitter are reduced to a residual error of 0.8ps, and the output eye width and height are improved by 84% and 61%, respectively, at a data-rate of 12.8Gbps.본 연구에서 용량을 최대화하면서도 리프레시 전력을 최소화할 수 있는 새로운 메모리 구조인 관리형 DRAM 솔루션을 위한 컨트롤러 PHY를 제시하였다. 이와 같은 고용량 DRAM 인터페이스에서는 많은 DRAM 칩이 명령 / 주소 (C/A) 채널을 공유하고 있어서 심볼 간 간섭이 발생한다. 본 연구에서는 이러한 C/A 채널에서의 심볼 간 간섭을 줄이기 위해 펄스 기반 피드 포워드 이퀄라이저 (PB-FFE)를 채택하였다. 또한 본 연구의 컨트롤러 PHY는 DDR4 표준에 지정된 모든 트레이닝 시퀀스를 지원한다. 링크 트레이닝을 효율적으로 수행하고 트레이닝 시간을 줄이기 위해 글리치가 발생하지 않는 디지털 제어 지연 라인 (DCDL)을 채택하였다. 컨트롤러 PHY의 DQ 송신기는 출력 대기 시간을 줄이기 위해 쿼터 레이트 구조를 채택하였다. 쿼터 레이트 송신기의 경우에는 직교 클럭 간 위상 오류가 출력 신호의 무결성에 영향을 주게 된다. 이러한 영향을 최소화하기 위해 본 연구에서는 출력 단의 4 : 1 직렬 변환기의 두 복제본을 사용하여 클록 신호 위상 오류를 수정하는 QEC (Quadrature Error Corrector)를 제안하였다. 복제된 2개의 직렬 변환기의 출력을 비교하고 균등화하기 위해 펄스 수축 지연 라인이 사용되었다. 컨트롤러 PHY는 55nm CMOS 공정으로 제조되었다. PB-FFE는 1067Mbps에서 C/A 채널 타이밍 마진을 0.23UI에서 0.29UI로 증가시킨다. 읽기 트레이닝 후 읽기 타이밍 및 전압 마진은 2133Mbps에서 0.53UI 및 211mV이고, 쓰기 트레이닝 후 쓰기 마진은 0.72UI 및 230mV이다. QEC의 효과를 검증하기 위해 QEC를 포함한 프로토 타입 쿼터 레이트 송신기를 65nm CMOS의 다른 칩으로 제작하였다. QEC를 적용한 실험 결과, 송신기의 출력 위상 오류가 0.8ps의 잔류 오류로 감소하고, 출력 데이터 눈의 폭과 높이가 12.8Gbps의 데이터 속도에서 각각 84 %와 61 % 개선되었음을 보여준다.CHAPTER 1 INTRODUCTION 1 1.1 MOTIVATION 1 1.1.1 HEAVY LOAD C/A CHANNEL 5 1.1.2 QUARTER-RATE ARCHITECTURE IN DQ TRANSMITTER 7 1.1.3 SUMMARY 8 1.2 THESIS ORGANIZATION 10 CHAPTER 2 ARCHITECTURE 11 2.1 MDS DIMM STRUCTURE 11 2.2 MDS CONTROLLER 15 2.3 MDS CONTROLLER PHY 17 2.3.1 INITIALIZATION SEQUENCE 20 2.3.2 LINK TRAINING FINITE-STATE MACHINE 23 2.3.3 POWER DOWN MODE 28 CHAPTER 3 PULSE-BASED FEED-FORWARD EQUALIZER 29 3.1 COMMAND/ADDRESS CHANNEL 29 3.2 COMMAND/ADDRESS TRANSMITTER 33 3.3 PULSE-BASED FEED-FORWARD EQUALIZER 35 CHAPTER 4 CIRCUIT IMPLEMENTATION 39 4.1 BUILDING BLOCKS 39 4.1.1 ALL-DIGITAL PHASE-LOCKED LOOP (ADPLL) 39 4.1.2 ALL-DIGITAL DELAY-LOCKED LOOP (ADDLL) 44 4.1.3 GLITCH-FREE DCDL CONTROL 47 4.1.4 DUTY-CYCLE CORRECTOR (DCC) 50 4.1.5 DQ/DQS TRANSMITTER 52 4.1.6 DQ/DQS RECEIVER 54 4.1.7 ZQ CALIBRATION 56 4.2 MODELING AND VERIFICATION OF LINK TRAINING 59 4.3 BUILT-IN SELF-TEST CIRCUITS 66 CHAPTER 5 QUADRATURE ERROR CORRECTOR USING REPLICA SERIALIZERS AND PULSE-SHRINKING DELAY LINES 69 5.1 PHASE CORRECTION USING REPLICA SERIALIZERS AND PULSE-SHRINKING UNITS 69 5.2 OVERALL QEC ARCHITECTURE AND ITS OPERATION 71 5.3 FINE DELAY UNIT IN THE PSDL 76 CHAPTER 6 EXPERIMENTAL RESULTS 78 6.1 CONTROLLER PHY 78 6.2 PROTOTYPE QEC 88 CHAPTER 7 CONCLUSION 94 BIBLIOGRAPHY 96Docto

Search for Nanosecond Near-infrared Transients around 1280 Celestial Objects

Stars and planetary system

Design, Analysis and Implementation of DLL clock generator

In this paper we present design, analysis and implementation of Delay Locked Loop (DLL) based clock generator circuits. In this work a DLL has been proposed the design uses dynamic phase detector (PD) for phase detection. Voltage controlled delay line (VCDL) of proposed DLL consists of twelve delay elements. Current starved inverters have been used as delay element. In this paper, a proposed duty cycle corrector solves the problem of the sensitivity to half transparent (HT) architecture and the stuck locking error in the DLL simultaneously proposed DLL is designed to work at an input frequency of 250MHz. The design also generates an output of 3GHz using a frequency multiplication block. The design uses 180nm CMOS process technology and consumes 1.88mW of power at 1.8V

The Fluorescence Detector of the Pierre Auger Observatory

The Pierre Auger Observatory is a hybrid detector for ultra-high energy cosmic rays. It combines a surface array to measure secondary particles at ground level together with a fluorescence detector to measure the development of air showers in the atmosphere above the array. The fluorescence detector comprises 24 large telescopes specialized for measuring the nitrogen fluorescence caused by charged particles of cosmic ray air showers. In this paper we describe the components of the fluorescence detector including its optical system, the design of the camera, the electronics, and the systems for relative and absolute calibration. We also discuss the operation and the monitoring of the detector. Finally, we evaluate the detector performance and precision of shower reconstructions.Comment: 53 pages. Submitted to Nuclear Instruments and Methods in Physics Research Section

Universal Digital Controller for Boost CCM Power Factor Correction Stages Based on Current Rebuilding Concept

Continuous conduction mode power factor correction (PFC) without input current measurement is a step forward with respect to previously proposed PFC digital controllers. Inductor volt-second (vsL) measurement in each switching period enables digital estimation of the input current; however, an accurate compensation of the small errors in the measured vsL is required for the estimation to match the actual current. Otherwise, they are accumulated every switching period over the half-line cycle, leading to an appreciable current distortion. A vsL estimation method is proposed, measuring the input (vg) and output voltage (vo). Discontinuous conduction mode (DCM) occurs near input line zero crossings and is detected by measuring the drain-to-source MOSFET voltage vds. Parasitic elements cause a small difference between the estimated voltage across the inductor based on input and output voltage measurements and the actual one, which must be taken into account to estimate the input current in the proposed sensorless PFC digital controller. This paper analyzes the current estimation error caused by errors in the ON-time estimation, voltage measurements, and the parasitic elements. A new digital feedback control with high resolution is also proposed. It cancels the difference between DCM operation time of the real input current, (TDCMg) and the estimated DCM time (TDCMreb). Therefore, the current estimation is calibrated using digital signals during operation in DCM. A fast feedforward coarse time error compensation is carried out with the measured delay of the drive signal, and a fine compensation is achieved with a feedback loop that matches the estimated and real DCM time. The digital controller can be used in universal applications due to the ability of the DCM time feedback loop to autotune based on the operation conditions (power level, input voltage, output v- ltage...), which improves the operation range in comparison with previous solutions. Experimental results are shown for a 1-kW boost PFC converter over a wide power and voltage range

Relationship of servant leadership with employee in-role and extra-role performance in GLC’s of Malaysia

This research aims to study the relationship of servant leadership with employee performance of in-role and extra role performance. Servant leadership, and its relationship with employee OCB and task performance are discussed to start with. Though some literature is available on links of servant leadership with employee task performance or Organizational Citizenship Behaviors, but how these two behaviors interact is not explained much. This paper explains that servant leadership has positive relationship with OCB. Though, other leadership approaches are different from servant leadership as its focus is on personal integrity and lasting relationships with employees

Power factor correction in a single phase AC to DC converter

Electronic equipments recently in use ( PCs, TVs, and Telecommunication Equipments etc.) require power conditioning of some form, typically rectification, for their proper working. But since they have non-linear input characteristics and they are connected the electricity distribution network they produce a non-sinusoidal line current. Current of frequency components which are multiples of the natural frequency are produced that are otherwise called the line harmonics. With constantly increasing demand of these kind of equipments at a high rate, line current harmonics have become a significant problem. There has been an introduction of a lot of international standards which pose limitations on the harmonic content in the line currents of equipments connected to electricity distribution networks. This calls for measures to reduce the line current harmonics which is also otherwise known as Power Factor Correction - PFC. There exist two kinds of power factor correction techniques – passive power factor correction and active power factor correction. In this thesis we tried to devise an active power factor correction method for improvement of the power factor. In this work the advantages of a boost converter is combined with that of the average current mode control to implement the technique. UC3854 was used to design the power factor corrector. This integrated circuit had all the circuits necessary to control a power factor corrector and was designed to implement the average current mode control