Aluminium and iron record for the last 28 kyr derived from the Antarctic EDC96 ice core using new CFA methods

AbstractSpectrofluorimetric and spectrophotometric continuous flow analysis (CFA) methods were developed and applied to the determination of aluminium and iron in EPICA Dome C (East Antarctica) ice-core samples (6–585m depth). The methods are able to measure the fraction of Al and Fe which can be detected once the sample is filtered on a 5.0 μm membrane and acidified to pH 2. Both the methods present high sensitivity (detection limit of 10 ng L–1 for Al and 50 ng L–1 for Fe) and reproducibility (5% at sub-ppb level). The Fe and Al profiles show sharp decreases in concentrations in the last glacial/interglacial transition, reflecting the decreasing dust aerosol load. The two elements show a different pattern during the Antarctic Cold Reversal (ACR) climatic change, with high iron concentrations (similar to the glacial period) and low but increasing Al content during the ACR minimum. In order to interpret the Al and Fe data obtained by CFA, a comparison with Al and Fe composition, as measured by inductively coupled plasma sector field mass spectrometry (ICP-SFMS), was performed for Holocene, ACR and glacial periods. The percentage of CFA-Al with respect to ICP-SFMS-Al in the three periods shows a lower variability than CFA-Fe (3% in the glacial period and 64% in the ACR). This pattern may be explained by the different dominant iron sources in the different climatic periods. During the Last Glacial Maximum, Fe is proposed to arise mainly from insoluble continental dust, while a variety of ocean-recycled Fe, mainly distributed in fine particles and as more soluble species, shows a higher contribution in the ACR and, to a lesser extent, in the Holocene

Precision medicine and public health: New challenges for effective and sustainable health

The development of high-throughput omics technologies represents an unmissable opportunity for evidence-based prevention of adverse effects on human health. However, the applicability and access to multi-omics tests are limited. In Italy, this is due to the rapid increase of knowledge and the high levels of skill and economic investment initially necessary. The fields of human genetics and public health have highlighted the relevance of an implementation strategy at a national level in Italy, including integration in sanitary regulations and governance instruments. In this review, the emerging field of public health genomics is discussed, including the polygenic scores approach, epigenetic modulation, nutrigenomics, and microbiomes implications. Moreover, the Italian state of implementation is presented. The omics sciences have important implications for the prevention of both communicable and noncommunicable diseases, especially because they can be used to assess the health status during the whole course of life. An effective population health gain is possible if omics tools are implemented for each person after a preliminary assessment of effectiveness in the medium to long term

Infrastructure for Detector Research and Development towards the International Linear Collider

The EUDET-project was launched to create an infrastructure for developing and testing new and advanced detector technologies to be used at a future linear collider. The aim was to make possible experimentation and analysis of data for institutes, which otherwise could not be realized due to lack of resources. The infrastructure comprised an analysis and software network, and instrumentation infrastructures for tracking detectors as well as for calorimetry.Comment: 54 pages, 48 picture

Enhanced Logic Performance with Semiconducting Bilayer Graphene Channels

Realization of logic circuits in graphene with an energy gap (EG) remains one of the main challenges for graphene electronics. We found that large transport EGs (>100 meV) can be fulfilled in dual-gated bilayer graphene underneath a simple alumina passivation top gate stack, which directly contacts the graphene channels without an inserted buffer layer. With the presence of EGs, the electrical properties of the graphene transistors are significantly enhanced, as manifested by enhanced on/off current ratio, subthreshold slope and current saturation. For the first time, complementary-like semiconducting logic graphene inverters are demonstrated that show a large improvement over their metallic counterparts. This result may open the way for logic applications of gap-engineered graphene.Comment: Accepted by ACS Nan

Predicting needlestick and sharps injuries in nursing students: Development of the SNNIP scale

Aim: To develop an instrument to investigate knowledge and predictive factors of needlestick and sharps injuries (NSIs) in nursing students during clinical placements. Design: Instrument development and cross-sectional study for psychometric testing. Methods: A self-administered instrument including demographic data, injury epidemiology and predictive factors of NSIs was developed between October 2018–January 2019. Content validity was assessed by a panel of experts. The instrument's factor structure and discriminant validity were explored using principal components analysis. The STROBE guidelines were followed. Results: Evidence of content validity was found (S-CVI 0.75; I-CVI 0.50–1.00). A three-factor structure was shown by exploratory factor analysis. Of the 238 participants, 39% had been injured at least once, of which 67.3% in the second year. Higher perceptions of “personal exposure” (4.06, SD 3.78) were reported by third-year students. Higher scores for “perceived benefits” of preventive behaviours (13.6, SD 1.46) were reported by second-year students

Design of analog front-ends for the RD53 demonstrator chip

The RD53 collaboration is developing a large scale pixel front-end chip, which will be a tool to evaluate the performance of 65 nm CMOS technology in view of its application to the readout of the innermost detector layers of ATLAS and CMS at the HL-LHC. Experimental results of the characterization of small prototypes will be discussed in the frame of the design work that is currently leading to the development of the large scale demonstrator chip RD53A to be submitted in early 2017. The paper is focused on the analog processors developed in the framework of the RD53 collaboration, including three time over threshold front-ends, designed by INFN Torino and Pavia, University of Bergamo and LBNL and a zero dead time front-end based on flash ADC designed by a joint collaboration between the Fermilab and INFN. The paper will also discuss the radiation tolerance features of the front-end channels, which were exposed to up to 800 Mrad of total ionizing dose to reproduce the system operation in the actual experiment

Description and performance of track and primary-vertex reconstruction with the CMS tracker

A description is provided of the software algorithms developed for the CMS tracker both for reconstructing charged-particle trajectories in proton-proton interactions and for using the resulting tracks to estimate the positions of the LHC luminous region and individual primary-interaction vertices. Despite the very hostile environment at the LHC, the performance obtained with these algorithms is found to be excellent. For tbar t events under typical 2011 pileup conditions, the average track-reconstruction efficiency for promptly-produced charged particles with transverse momenta of pT > 0.9GeV is 94% for pseudorapidities of |η| < 0.9 and 85% for 0.9 < |η| < 2.5. The inefficiency is caused mainly by hadrons that undergo nuclear interactions in the tracker material. For isolated muons, the corresponding efficiencies are essentially 100%. For isolated muons of pT = 100GeV emitted at |η| < 1.4, the resolutions are approximately 2.8% in pT, and respectively, 10μm and 30μm in the transverse and longitudinal impact parameters. The position resolution achieved for reconstructed primary vertices that correspond to interesting pp collisions is 10–12μm in each of the three spatial dimensions. The tracking and vertexing software is fast and flexible, and easily adaptable to other functions, such as fast tracking for the trigger, or dedicated tracking for electrons that takes into account bremsstrahlung

Test beam performance of a CBC3-based mini-module for the Phase-2 CMS Outer Tracker before and after neutron irradiation

The Large Hadron Collider (LHC) at CERN will undergo major upgrades to increase the instantaneous luminosity up to 5–7.5×10$^{34}$ cm$^{-2}$s$^{-1}$. This High Luminosity upgrade of the LHC (HL-LHC) will deliver a total of 3000–4000 fb-1 of proton-proton collisions at a center-of-mass energy of 13–14 TeV. To cope with these challenging environmental conditions, the strip tracker of the CMS experiment will be upgraded using modules with two closely-spaced silicon sensors to provide information to include tracking in the Level-1 trigger selection. This paper describes the performance, in a test beam experiment, of the first prototype module based on the final version of the CMS Binary Chip front-end ASIC before and after the module was irradiated with neutrons. Results demonstrate that the prototype module satisfies the requirements, providing efficient tracking information, after being irradiated with a total fluence comparable to the one expected through the lifetime of the experiment

Trapping in irradiated p-on-n silicon sensors at fluences anticipated at the HL-LHC outer tracker

The degradation of signal in silicon sensors is studied under conditions expected at the CERN High-Luminosity LHC. 200 $\mu$m thick n-type silicon sensors are irradiated with protons of different energies to fluences of up to $3 \cdot 10^{15}$ neq/cm$^2$. Pulsed red laser light with a wavelength of 672 nm is used to generate electron-hole pairs in the sensors. The induced signals are used to determine the charge collection efficiencies separately for electrons and holes drifting through the sensor. The effective trapping rates are extracted by comparing the results to simulation. The electric field is simulated using Synopsys device simulation assuming two effective defects. The generation and drift of charge carriers are simulated in an independent simulation based on PixelAV. The effective trapping rates are determined from the measured charge collection efficiencies and the simulated and measured time-resolved current pulses are compared. The effective trapping rates determined for both electrons and holes are about 50% smaller than those obtained using standard extrapolations of studies at low fluences and suggests an improved tracker performance over initial expectations