Blending or Bonding? Mechanochromism of an Aggregachromic Mechanophore in a Thermoplastic Elastomer

A straightforward way for the preparation of mechanochromic polymers consists of incorporating a suitable content of a mechanophore in the polymeric matrix either by physical dispersion or via covalent functionalization. Although covalent incorporation may require demanding chemical efforts, this approach can offer significant advantages over physical dispersion. In this work, a common thermoplastic elastomer, styrene-b-(ethylene-co-butylene)-b-styrene triblock copolymer grafted with maleic anhydride (SEBS-MAH), was covalently functionalized with 1-aminomethylpyrene (AMP). MAH functional groups are covalently linked to the ethylene-co-butylene blocks, thus allowing a precise and selective confinement of the chromogenic AMP units in the soft block. Flat, fully conjugated pyrene units undergo the reversible formation of π-πaggregates, readily distinguishable by their red-shifted emission. These aggregates were heavily affected by the application of mechanical stimuli. Despite the low degree of mechanophore functionalization (about 1 wt %), uniaxial deformation of the polymer was reliably monitored via fluorescence and a clear drop in the excimer to monomer emission ratio (IE/IM) was observed starting from 50% of strain. The marked mechanochromism was confirmed by emission lifetime measurements and also by near-field investigations. In addition, the mechanoresponse showed good reversibility after repeated stress-relaxation cycles. Control experiments performed on formulations comprising a physical dispersion of pyrene in unfunctionalized SEBS showed faint excimer emission and a negligible mechanochromic response up to 5 wt % of doping, in substantial agreement with the scanning near-field optical microscopy analysis. An evident drop of the IE/IM ratio occurred for 10 wt % of pyrene, albeit the excimer emission remained predominant even at the highest deformation, being a smaller fraction of pyrene moieties involved. Overall, the covalent approach appeared as an elegant procedure to confine the chromogenic unit in the soft phase of block copolymers and thus to provide an elastomeric film showing a detectable and reversible mechanochromic response with a modest (i.e., ∼1 wt %) amount of pyrene molecules, i.e., 10 times smaller compared to the dispersed system

A high-sensitivity long-lifetime phosphorescent RIE additive to probe free volume-related phenomena in polymers

The photophysical behaviour of phosphorescent rigidification-induced emission (RIE) dyes is highly affected by their micro- and nanoenvironment. The lifetime measure of RIE dyes dispersed in polymers represents an effective approach to gain valuable information on polymer free volume and thus develop materials potentially able to self-monitor physical ageing and mechanical stresses

Reusable Cavitand‐Based Electrospun Membranes for the Removal of Polycyclic Aromatic Hydrocarbons from Water

The removal of toxic and carcinogenic polycyclic aromatic hydrocarbons (PAHs) from water is one of the most intractable environmental problems nowadays, because of their resistance to remediation. This work introduces a highly efficient, regenerable membrane for the removal of PAHs from water, featuring excellent filter performance and pH-driven release, thanks to the integration of a cavitand receptor in electrospun polyacrylonitrile (PAN) fibers. The role of the cavitand receptor is to act as molecular gripper for the uptake/ release of PAHs. To this purpose, the deep cavity cavitand BenzoQxCav is designed and synthetized and its molecular structure is elucidated via X-Ray diffraction. The removal efficiency of the new adsorbent material toward the 16 priority PAHs is demonstrated via GC-MS analyses at ng L−1 concentration. A removal efficiency in the 32%, to 99% range is obtained. The regeneration of the membrane is performed by exploiting the pH-driven conformational switching of the cavitand between the vase form, where the PAHs uptake takes place, to the kite one, where the PAHs release occurs. The absorbance and regeneration capability of the membrane are successfully tested in four uptake/release cycles and the morphological stability

Understanding Barriers Impacting upon Patient Wellbeing: A Nationwide Italian Survey and Expert Opinion of Dermatologists Treating Patients with Moderate-to-Severe Psoriasis

A nationwide cross-sectional online survey was administered to dermatologists managing patients with moderate-to-severe plaque psoriasis across Italy to obtain real-world dermatologists' perspectives on the impact of psoriasis and its treatment on patients' daily lives and quality of life (QoL). A total of 91 dermatologists (aged 39.1 +/- 11.2 years) completed a 31-question survey and workshop sessions were undertaken in order to identify the best management approach to achieve patient wellbeing. Social (4.2 +/- 0.1), physical (4.26 +/- 0.2) and mental components (4.1 +/- 0.3) were rated by dermatologists as contributing to patient wellbeing to similar extents. While a high proportion (85.4%; rating of 4.3 out of 5) of dermatologists felt that they considered the QoL of patients, a lower proportion (69.6%; rating of 3.7 out of 5) felt that patients were satisfied in this regard. The psoriasis area and severity index and body surface area were the instruments most frequently used to assess the physical domain, while interviews/questions and the dermatology life quality index were used to assess social and mental domains, with only 60% of dermatologists following up on these aspects. The importance of investigating the presence of comorbidities was recognized but not always carried out by many dermatologists, (>70%), particularly for obesity and anxiety/depression. This survey identified key components contributing to barriers impacting on the QoL of patients with moderate-to-severe psoriasis from the perspective of the dermatologist

Measurement of the top quark forward-backward production asymmetry and the anomalous chromoelectric and chromomagnetic moments in pp collisions at √s = 13 TeV

Abstract The parton-level top quark (t) forward-backward asymmetry and the anomalous chromoelectric (d̂ t) and chromomagnetic (μ̂ t) moments have been measured using LHC pp collisions at a center-of-mass energy of 13 TeV, collected in the CMS detector in a data sample corresponding to an integrated luminosity of 35.9 fb−1. The linearized variable AFB(1) is used to approximate the asymmetry. Candidate t t ¯ events decaying to a muon or electron and jets in final states with low and high Lorentz boosts are selected and reconstructed using a fit of the kinematic distributions of the decay products to those expected for t t ¯ final states. The values found for the parameters are AFB(1)=0.048−0.087+0.095(stat)−0.029+0.020(syst),μ̂t=−0.024−0.009+0.013(stat)−0.011+0.016(syst), and a limit is placed on the magnitude of | d̂ t| < 0.03 at 95% confidence level. [Figure not available: see fulltext.

Search for Physics beyond the Standard Model in Events with Overlapping Photons and Jets

Results are reported from a search for new particles that decay into a photon and two gluons, in events with jets. Novel jet substructure techniques are developed that allow photons to be identified in an environment densely populated with hadrons. The analyzed proton-proton collision data were collected by the CMS experiment at the LHC, in 2016 at root s = 13 TeV, and correspond to an integrated luminosity of 35.9 fb(-1). The spectra of total transverse hadronic energy of candidate events are examined for deviations from the standard model predictions. No statistically significant excess is observed over the expected background. The first cross section limits on new physics processes resulting in such events are set. The results are interpreted as upper limits on the rate of gluino pair production, utilizing a simplified stealth supersymmetry model. The excluded gluino masses extend up to 1.7 TeV, for a neutralino mass of 200 GeV and exceed previous mass constraints set by analyses targeting events with isolated photons.Peer reviewe

Measurement of the azimuthal anisotropy of Y(1S) and Y(2S) mesons in PbPb collisions at root s(NN)=5.02 TeV

The second-order Fourier coefficients (v(2)) characterizing the azimuthal distributions of Y(1S) and Y(2S) mesons produced in PbPb collisions at root s(NN) = 5.02 TeV are studied. The Y mesons are reconstructed in their dimuon decay channel, as measured by the CMS detector. The collected data set corresponds to an integrated luminosity of 1.7 nb(-1). The scalar product method is used to extract the v2 coefficients of the azimuthal distributions. Results are reported for the rapidity range vertical bar y vertical bar < 2.4, in the transverse momentum interval 0 < pT < 50 GeV/c, and in three centrality ranges of 10-30%, 30-50% and 50-90%. In contrast to the J/psi mesons, the measured v(2) values for the Y mesons are found to be consistent with zero. (C) 2021 The Author(s). Published by Elsevier B.V.Peer reviewe

Calibration of the CMS hadron calorimeters using proton-proton collision data at root s=13 TeV

Methods are presented for calibrating the hadron calorimeter system of theCMSetector at the LHC. The hadron calorimeters of the CMS experiment are sampling calorimeters of brass and scintillator, and are in the form of one central detector and two endcaps. These calorimeters cover pseudorapidities vertical bar eta vertical bar ee data. The energy scale of the outer calorimeters has been determined with test beam data and is confirmed through data with high transverse momentum jets. In this paper, we present the details of the calibration methods and accuracy.Peer reviewe

Measurement of the Jet Mass Distribution and Top Quark Mass in Hadronic Decays of Boosted Top Quarks in pp Collisions at root s=13 TeV

A measurement is reported of the jet mass distribution in hadronic decays of boosted top quarks produced in pp collisions at root s = 13 TeV. The data were collected with the CMS detector at the LHC and correspond to an integrated luminosity of 35.9 fb(-1). The measurement is performed in the lepton + jets channel of t (t) over bar events, where the lepton is an electron or muon. The products of the hadronic top quark decay t -> bW -> bq (q) over bar' are reconstructed as a single jet with transverse momentum larger than 400 GeV. The t (t) over bar cross section as a function of the jet mass is unfolded at the particle level and used to extract a value of the top quark mass of 172.6 +/- 2.5 GeV. A novel jet reconstruction technique is used for the first time at the LHC, which improves the precision by a factor of 3 relative to an earlier measurement. This highlights the potential of measurements using boosted top quarks, where the new technique will enable future precision measurements.Peer reviewe

Search for top squark pair production in a final state with two tau leptons in proton-proton collisions at root s=13 TeV

A search for pair production of the supersymmetric partner of the top quark, the top squark, in proton-proton collision events at s = 13 TeV is presented in a final state containing hadronically decaying tau leptons and large missing transverse momentum. This final state is highly sensitive to high-tan beta or higgsino-like scenarios in which decays of electroweak gauginos to tau leptons are dominant. The search uses a data set corresponding to an integrated luminosity of 77.2 fb(-1), which was recorded with the CMS detector during 2016 and 2017. No significant excess is observed with respect to the background prediction. Exclusion limits at 95% confidence level are presented in the top squark and lightest neutralino mass plane within the framework of simplified models, in which top squark masses up to 1100 GeV are excluded for a nearly massless neutralino.Peer reviewe