Radio over fibre distribution systems for ultra-wide band and millimetre wave applications

Short range wireless technology such as ultra-wideband (UWB) and 60 GHz millimetre wave (mm-wave) play a key role for wireless connectivity in indoor home, office environment or large enclosed public areas. UWB has been allocated at the frequency band 3.1-10.6 GHz with an emission power below -41.3 dBm. Mm-wave signals around 60 GHz have also attracted much attention to support high-speed data for short range wireless applications. The wide bandwidth and high allowable transmit power at 60 GHz enable multi-Gbps wireless transmission over typical indoor distances. Radio-over-fibre (RoF) systems are used to extend the propagation distance of both UWB and mm-wave signals over hundred of meters inside a building. UWB or mm-wave signals over fibre can be generated first at the central office before being distributed to the remote access points through optical fibre. In this work, we investigate two new techniques to generate and distribute UWB signals. These techniques are based on generating Gaussian pulse position modulation (PPM) using a gain switched laser (GSL). The simulation and experimental results have been carried out to show the suitability of employing gain switching in UWB over fibre systems (UWBoF) to develop a reliable, simple, and low cost technique for distributing UWB pulses. The second part of this work proposes two configurations for optical mm-wave generation and transmission of 3 Gbps downstream data based on GSL. We investigate the distribution of these two methods over fibre with wireless link, and demonstrate the system simplicity and cost efficiency for mm-wave over fibre systems. Both configurations are simulated to verify our obtained results and show system performance at higher bit rates. In the third part, we generate phase modulated mm-waves by using an external injection of a modulated light source into GSL. The performance of this system is experimentally investigated and simulated for different fiber links

CMOS Signal Synthesizers for Emerging RF-to-Optical Applications

The need for clean and powerful signal generation is ubiquitous, with applications spanning the spectrum from RF to mm-Wave, to into and beyond the terahertz-gap. RF applications including mobile telephony and microprocessors have effectively harnessed mixed-signal integration in CMOS to realize robust on-chip signal sources calibrated against adverse ambient conditions. Combined with low cost and high yield, the CMOS component of hand-held devices costs a few cents per part per million parts. This low cost, and integrated digital processing, make CMOS an attractive option for applications like high-resolution imaging and ranging, and the emerging 5-G communication space. RADAR techniques when expanded to optical frequencies can enable micrometers of resolution for 3D imaging. These applications, however, impose upto 100x more exacting specifications on power and spectral purity at much higher frequencies than conventional RF synthesizers. This generation of applications will present unconventional challenges for transistor technologies - whether it is to squeeze performance in the conventionally used spectrum, already wrung dry, or signal generation and system design in the relatively emptier mm-Wave to sub-mmWave spectrum, much of the latter falling in the ``Terahertz Gap". Indeed, transistor scaling and innovative device physics leading to new transistor topologies have yielded higher cut-off frequencies in CMOS, though still lagging well behind SiGe and III-V semiconductors. To avoid multimodule solutions with functionality partitioned across different technologies, CMOS must be pushed out of its comfort zone, and technology scaling has to have accompanying breakthroughs in design approaches not only at the system but also at the block level. In this thesis, while not targeting a specific application, we seek to formulate the obstacles in synthesizing high frequency, high power and low noise signals in CMOS and construct a coherent design methodology to address them. Based on this, three novel prototypes to overcome the limiting factors in each case are presented. The first half of this thesis deals with high frequency signal synthesis and power generation in CMOS. Outside the range of frequencies where the transistor has gain, frequency generation necessitates harmonic extraction either as harmonic oscillators or as frequency multipliers. We augment the traditional maximum oscillation frequency metric (fmax), which only accounts for transistor losses, with passive component loss to derive an effective fmax metric. We then present a methodology for building oscillators at this fmax, the Maximum Gain Ring Oscillator. Next, we explore generating large signals beyond fmax through harmonic extraction in multipliers. Applying concepts of waveform shaping, we demonstrate a Power Mixer that engineers transistor nonlinearity by manipulating the amplitudes and relative phase shifts of different device nodes to maximize performance at a specific harmonic beyond device cut-off. The second half proposes a new architecture for an ultra-low noise phase-locked loop (PLL), the Reference-Sampling PLL. In conventional PLLs, a noisy buffer converts the slow, low-noise sine-wave reference signal to a jittery square-wave clock against which the phase of a noisy voltage-controlled oscillator (VCO) is corrected. We eliminate this reference buffer, and measure phase error by sampling the reference sine-wave with the 50x faster VCO waveform already available on chip, and selecting the relevant sample with voltage proportional to phase error. By avoiding the N-squared multiplication of the high-power reference buffer noise, and directly using voltage-mode phase error to control the VCO, we eliminate several noisy components in the controlling loop for ultra-low integrated jitter for a given power consumption. Further, isolation of the VCO tank from any varying load, unlike other contemporary divider-less PLL architectures, results in an architecture with record performance in the low-noise and low-spur space. We conclude with work that brings together concepts developed for clean, high-power signal generation towards a hybrid CMOS-Optical approach to Frequency-Modulated Continuous-Wave (FMCW) Light-Detection-And-Ranging (LIDAR). Cost-effective tunable lasers are temperature-sensitive and have nonlinear tuning profiles, rendering precise frequency modulations or 'chirps' untenable. Locking them to an electronic reference through an electro-optic PLL, and electronically calibrating the control signal for nonlinearity and ambient sensitivity, can make such chirps possible. Approaches that build on the body of advances in electrical PLLs to control the performance, and ease the specification on the design of optical systems are proposed. Eventually, we seek to leverage the twin advantages of silicon-intensive integration and low-cost high-yield towards developing a single-chip solution that uses on-chip signal processing and phased arrays to generate precise and robust chirps for an electronically-steerable fine LIDAR beam

Lasers à blocage de modes à base de boîtes et bâtonnets quantiques pour les peignes de fréquences optiques

Optical frequency combs, generating tens of equally spaced optical carriers from a single laser source, are very attractive for next-generation wavelength division multiplexing (WDM) communication systems. This PhD thesis presents a study on the optical frequency combs generated by mode-locked laser diodes based on low-dimensional semiconductor nanostructures. In this work, the mode-locking performances of single-section Fabry-Pérot lasers based on different material systems are compared on the basis of the optical spectrum width, the timing jitter and pulse generation capabilities. Then, noticing that InAs quantum dashes grown on InP exhibit on average better characteristics than other examined materials, their unique properties in terms of comb stability and pulse chirp are studied in more detail. Laser chirp, in particular, is first investigated by frequency resolved optical gating (FROG) characterizations. Then, chromatic dispersion of the laser material is assessed in order to verify whether it can account for the large chirp values measured by FROG. For that, a high sensitivity optical frequency-domain reflectometry setup is used and its measurement capabilities are extensively studied and validated. Finally, the combs generated by quantum dash mode-locked lasers are successfully employed for high data rate transmissions using direct-detection optical orthogonal frequency division multiplexing. Terabit per second capacities, as well as the low cost of this system architecture, appear to be particularly promising for future datacom applicationsLes peignes de longueurs d'onde, produisant des dizaines de porteuses optiques régulièrement espacées à partir d'une seule source laser, présentent un grand intérêt pour les systèmes de communication à haut débit. Ce travail de thèse porte sur les peignes générés par les diodes laser à blocage de modes basées sur des nanostructures semi-conductrices à basse dimensionnalité. Dans cette étude, les performances en verrouillage de modes de lasers Fabry-Pérot mono-section basés sur différents systèmes de matériaux sont comparées sur la base de la largeur du spectre optique d'émission et de la capacité à produire des impulsions courtes à faible gigue temporelle. En remarquant que les lasers à base de bâtonnets quantiques InAs sur InP présentent de meilleures caractéristiques par rapport aux autres matériaux examinés, leurs propriétés spécifiques en termes de stabilité des peignes de fréquences optiques et de chirp des impulsions sont étudiées plus en détail. Le chirp est d'abord étudié par la technique FROG (frequency-resolved optical gating). Ensuite, la dispersion chromatique du matériau laser est évaluée afin de vérifier si elle peut expliquer les grandes valeurs de chirp mesurées par FROG. Pour cela la technique de réflectométrie optique dans le domaine fréquentiel est utilisée et ses capacités uniques de mesure ont été étudiées et validées. Enfin, ces lasers sont employés avec succès pour les transmissions haut débit à l'aide de la technique de modulation optique OFDM (orthogonal frequency-division multiplexing) en détection directe. Débits de l'ordre du térabit par seconde, ainsi que le faible coût de l’architecture du système, sont très prometteurs pour les data center

Optical frequency comb technology for ultra-broadband radio-frequency photonics

The outstanding phase-noise performance of optical frequency combs has led to a revolution in optical synthesis and metrology, covering a myriad of applications, from molecular spectroscopy to laser ranging and optical communications. However, the ideal characteristics of an optical frequency comb are application dependent. In this review, the different techniques for the generation and processing of high-repetition-rate (>10 GHz) optical frequency combs with technologies compatible with optical communication equipment are covered. Particular emphasis is put on the benefits and prospects of this technology in the general field of radio-frequency photonics, including applications in high-performance microwave photonic filtering, ultra-broadband coherent communications, and radio-frequency arbitrary waveform generation.Comment: to appear in Laser and Photonics Review

Digital Compensation of Transmission Impairments in Multi-Subcarrier Fiber Optic Transmission Systems

Time and again, fiber optic medium has proved to be the best means for transporting global data traffic which is following an exponential growth trajectory. Rapid development of high bandwidth applications since the past decade based on cloud, virtual reality, 5G and big data to name a few have resulted in a sudden surge of research activities across the globe to maximize effective utilization of available fiber bandwidth which until then was supporting low speed (< 10Gbps) services. To this end, higher order modulation formats together with multicarrier super channel based fiber optic transmission systems have proved to enhance spectral efficiency and achieve multi tera-bit per second bit rates. However, spectrally efficient systems are extremely sensitive to transmission impairments stemming from both optical devices and fiber itself. Therefore, such systems mandate the use of robust digital signal processing (DSP) to compensate and/or mitigate the undesired artifacts. The central theme of this research is to propose and validate few efficient DSP techniques to compensate specific impairments as delineated in the next three paragraphs. For short reach data center and passive optical network related applications which adopt direct detection, a single optical amplifier is generally used to meet the power budget requirements in order to achieve the desired receiver sensitivity or bit error ratio (BER). Semiconductor Optical Amplifier (SOA) with its small form factor is a low-cost power booster that can be designed to operate in any desired wavelength and more importantly can be integrated with other electro-optic components. However, saturated SOAs exhibit nonlinear amplification that introduce distortions on the amplified signal. Alongside SOA, the photodiode also introduces nonlinear mixing among the signal subcarriers in the form of Signal-Signal Beat Interference (SSBI). In this research, we study the impact of SOA nonlinearity on the effectiveness of SSBI compensation in a direct detection OFDM based transmission system. We experimentally demonstrate a digital compensation technique to undo the SOA nonlinearity effect by digitally backpropagating the received signal through a virtual SOA with inverse gain characteristics, thereby effectively eliminating the SSBI. With respect to transmission sources, laser technology has made some significant strides especially in the domain of multiwavelength sources such as quantum dot passive mode-locked laser (QD-PMLL) based optical frequency combs. In the present research work, we characterize the phase dynamics of comb lines from a QD-PMLL based on a novel multiheterodyne coherent detection technique. The inherently broad linewidth of comb lines which is on the order of tens of MHz make it difficult for conventional digital phase noise compensation algorithms to track the large phase noise especially for low baud rate subcarriers using higher cardinality modulation formats. In the context of multi-subcarrier, Nyquist pulse shaped, superchannel transmission system with coherent detection, we demonstrate through measurements and numerical simulations an efficient phase noise compensation technique called “Digital Mixing” that operates using a shared pilot tone exploiting mutual phase coherence among the comb lines. For QPSK and 16 QAM modulation formats, digital mixing provided significant improvement in BER performance in comparison to conventional phase tracking algorithms. Coherent solutions for regional and long haul systems make use of in-line optical amplifiers to compensate fiber loss. Ideally, distributed amplification based on stimulated Raman effect offers enhanced optical signal to noise ratios (OSNR) compared to lumped amplification using erbium doped fiber amplifiers and semiconductor optical amplifiers. However, this benefit of enhanced OSNRs in distributed Raman amplification is offset by the transfer of intensity noise of pump laser on to both signal’s phase and intensity, resulting in performance degradation. In this work, we propose and experimentally validate a practical pilot aided relative phase noise compensation technique for forward pumped distributed Raman amplified, digital subcarrier multiplexed coherent transmission systems

Broadband access networks using hybrid radio/fiber systems

Developing broadband access networks is one of the most urgent needs in the telecommunications world. The wireless systems provide an efficient solution to address the requirements for last mile connectivity of data, Internet and voice services Radio systems using millimetre-wave frequencies can supply home users with capacities in the order of 50-200 Mbit/s Such bit rates allow the transmission of broadband applications including digital TV, video-on-demand etc In order to provide the massive capacities that are required for the distribution of such broadband data between Central Station and Base Stations, optical fiber can be employed The enormous transmission bandwidth and low loss of the fiber ensure that high capacity microwave signals can be encoded on an optical carrier and successfully transmitted from a Central to Base Station. The goal of this project was to develop and test a radio over fiber communication system This involved investigating the generation of microwave optical signals for transmission in optical fiber, followed by an examination of the effect of fiber propagation on the microwave optical signals