Introduction to Radio-frequency Identification (RFID)

This project presents the fundamental aspects of the RFID (Radio-frequency identifica-tion) technology used to establish wireless communications. The project focuses on thepassive mode of RFID, where the receiver does not have any power supply, which allowsits miniaturization and low cost.On the other hand, two articles from different authors are analyzed. The first consists onthe design of a very low power passive receiver through various techniques of optimizationin the hardware’s manufacture.In the second, a drone is used as an intermediate element between the transmitter and thereceiver to extend up to 10 times the typical range of passive RFID. The study focuses onthe treatment of the RF signal to considerably eliminate the interferences and to preciselylocalize the receiver.Outgoin

Advanced Radio Frequency Identification Design and Applications

Radio Frequency Identification (RFID) is a modern wireless data transmission and reception technique for applications including automatic identification, asset tracking and security surveillance. This book focuses on the advances in RFID tag antenna and ASIC design, novel chipless RFID tag design, security protocol enhancements along with some novel applications of RFID

Design and Modelling of Passive UHF RFID Tags for Energy Efficient Liquid Level Detection Applications. A study of various techniques in the design, modelling, optimisation and deployment of RFID reader and passive UHF RFID tags to achieve effective performance for liquid sensing applications

Sewer and oil pipeline spillage issues have become major causes of pollution in urban and rural areas usually caused by blockages in the water storage and drainage system, and oil spillage of underground oil pipelines. An effective way of avoiding this problem will be by deploying some mechanism to monitor these installations at each point in time and reporting unusual liquid activity to the relevant authorities for prompt action to avoid a flooding or spillage occurrence. This research work presents a low cost energy efficient liquid level monitoring technique using Radio Frequency Identification Technology. Passive UHF RFID tags have been designed, modelled and optimized. A simple rectangular tag, the P-shaped tag and S-shaped tag with UHF band frequency of operation (850-950 MHz) has been designed and modelled. Detailed parametric analysis of the rectangular tag is made and the optimised design results analysed and presented in HFSS and Matlab. The optimised rectangular tag designs are then deployed as level sensors in a gully pot. Identical tags were deployed to detect 4 distinct levels in alternate positions and a few inches in seperation distance within the gully pot height (Low, Mid, High and Ultra high). The radiation characteristic of tag sensors in deployment as modelled on HFSS is observed to show consistent performance with application requirements. An in-manhole chamber antenna for an underground communication system is analysed, designed, deployed and measured. The antenna covers dual-band impedance bandwidths (i.e. 824 to 960 MHz, and 1710 to 2170 MHz). The results show that the antenna prototype exhibits sufficient impedance bandwidth, suitable radiation characteristics, and adequate gains for the required underground wireless sensor applications. Finally, a Linearly Shifted Quadrifilar Helical Antenna (LSQHA) designed using Genetic Algorithm optimisation technique for adoption as an RFID reader antenna is proposed and investigated. The new antenna confirms coverage of the RFID bandwidth 860-960 MHz with acceptable power gain of 13.1 dBi.Petroleum Technology Development Fund (PTDF) and National Space Research and Development Agency (NASRDA)

Ultra Low Power IEEE 802.15.4/ZIGBEE Compliant Transceiver

Low power wireless communications is the most demanding request among all wireless users. A battery life that can survive for years without being replaced, makes it realistic to implement many applications where the battery is unreachable (e.g. concrete walls) or expensive to change (e.g underground applications). IEEE 802.15.4/ZIGBEE standard is published to cover low power low cost applications, where the battery life can last for years, because of the 1% duty cycle of operation. A fully integrated 2.4GHz IEEE802.15.4 Compliant transceiver suitable for low power, low cost ZIGBEE applications is implemented. Direct conversion architecture is used in both Receiver and Transmitter, to achieve the minimum possible power and area. The chip is fabricated in a standard 0.18um CMOS technology. In the transmit mode, the transmitter chain (Modulator to PA) consumes 25mW, while in the receive mode, the iv receiver chain (LNA to Demodulator) consumes 5mW. The Integer-N Frequency Synthesizer consumes 8.5mW. Other Low power circuits are reported; A 13.56 Passive RFID tag and a low power ADC suitable for Built-In-Testing applications

Design of a Low-Cost Passive UHF RFID tag in 0.18um CMOS technology

The work addresses the design of a passive UHF Radio-Frequency Identification (RFID) tag. In order to realize a product able to be competitive in the RFID expanding market, a cost reduction policy has been applied in the design: a general purpose digital technology has been employed, resorting to specific techniques in order to overcome the limitations due to the lack of process options. Such solutions are accurately described, and every block composing the transponder analog frontend is analyzed, highlighting advantages and disadvantages of the proposed architectures with respect to the ones present in literature. The circuits theory is validated through simulations and experimental data.Il lavoro di tesi è imperniato sul progetto di un tag passivo per l'Identificazione a Radio-Frequenza (RFID) operante nelle bande UHF. Per il progetto è stata applicata una politica di riduzione dei costi, così da proporre un prodotto in grado di essere competitivo nel fiorente mercato dell'RFID: è stata scelta una tecnologia digitale general-purpose, e specifiche tecniche di progettazione sono state utilizzate per superare le limitazioni dovute alla scarsità di opzioni di processo. Le soluzioni adottate sono descritte accuratamente, ed è riportata l'analisi di ogni singolo blocco componente il frontend analogico, evidenziando vantaggi e svantaggi delle architetture proposte rispetto a quelle presenti in letteratura. La validità della teoria alla base dei circuiti è stata verificata tramite simulazioni e dati sperimentali

A Novel Micro Piezoelectric Energy Harvesting System

(Doktora) -- İstanbul Teknik Üniversitesi, Fen Bilimleri Enstitüsü, 2007(PhD) -- İstanbul Technical University, Institute of Science and Technology, 2007Bu tezde yeni bir titreşim temelli mikro enerji harmanlayıcı sistemi önerilmiştir. Titreşimler ve ani hareketler, mekanik yapının sadece eğilmesine değil aynı zamanda gerilmesine yol açar, bu sayede sistem doğrusal olmayan bölgede çalışır. İnce piezoelektrik film tabakası mekanik stresi elektrik enerjisine çevirir. Mikrowatt mertebesinde güç seviyeleri mm3’lük aletlerle elde edilebilir, bu da güneş panellerinde elde edilen güç yoğunlukları kadar yüksektir. Algılayıcı kabiliyeti sayesinde bilgi depolayabilen, kum tanesi büyüklüğünde olan ve üretiminde kullanılan temel malzeme silikon olan bu aletler “zeki kum” olarak isimlendirilmiştir. Mekanik yapının modellenmesi ve tasarımı geliştirilmiş ve üretim sonuçları da ayrıca verilmiştir. Sistemin bilgi gönderebilmesi ve alabilmesi amacıyla iyi bilinen RFID teknolojisi tabanlı bir kablosuz haberleşme yöntemi önerilmiştir. Bu bağlamda, paket taşımacılığında sürekli ivme denetleme, sınır güvenliği için kendinden beslemeli algılayıcılar, çabuk bozulan yiyeceklerin taşımacılığında sıcaklık denetleme ve pilsiz kalp atışı algılayıcı gibi birçok uygulama önerilmiştir.In this thesis, a novel, vibration based micro energy harvester system is proposed. Vibrations or sudden movements cause the mechanical structure does not only bend but also stretch, thus working in non-linear regime. The piezoelectric thin film layer converts the mechanical stress into the electrical energy. Microwatts of power can be achieved with a mm3 device which yields a high power density levels on the order of the solar panels. This device is named “smart sand”, because it has also sensor capabilities that can store information, its size is almost a sand grain and the main material used for the fabrication is silicon. The modeling and design of the mechanical structure has been developed and fabrication results have also been given in the thesis. In order for the system to send and receive the information, a wireless communication scheme is proposed which is based on the well-known RFID technology. In this concept, several applications are proposed such as continuous acceleration monitoring in package delivery, self-powered sensors for homeland security, temperature monitoring of the perishable food item delivery and a batteryless heart rate sensor.DoktoraPh

Non-linear shunt regulator based on a PWM RF power detector for RFID applications

Radio Frequency Identification (RFID) is utilized in a variety of applications, includ ing tagging animals and objects to make their identification (ID) easier to read and man age, similar to a bar code or QR code. In this regard, the goal of this research is to improve RFID transponder power regulation in order to increase reader distance. This thesis de scribes a non-linear shunt regulator that employs a Radio Frequency (RF) power detector based on the Pulse Width Modulation (PWM) technique to aim magnetically coupled RFID transponders. A quick voltage-clamp loop and a slow-accurate power detector loop are used in the proposed regulator architecture. The first loop ensures over-voltage pro tection, while the second loop gradually corrects the first loop’s imprecision based on the measured input power. To contextualize the issues and improvements of the new design, the state-of-the-art in RFID power management and RF power detector are covered first. The new architecture is specified after theoretical development, electrical simulations, and the design of the new architecture is implemented. The entire regulator design was prototyped as part of a commercial low-frequency (134 kHz) RFID transponder in a 180 nm CMOS process. The regulator deal with a sinusoidal voltage at its input generated by the LC tank that extracts energy from the reader to supply its circuitry. The use of a 3.3V standard process for the analog circuitry in order to decrease the fabrication cost by not using the high voltage module (5 V for example) complicates the system design. Even though the proposed solution aims to regulate the input voltage precisely at 3.6 V maximum, the maximum voltage supported by 3.3 V standard module using two feedback is achieved. The total RFID transponder area of 870x870 µm² was obtained, with 130x230 µm² related to the regulator circuit area only. Both resonant and supply capacitors are imple mented on the chip. The complete system consumes a maximum current of 4.5 µA, over a wide RF input power range that is modulated by the distance between the reader and the transponder. As the power detector corrects the imprecision of the shunt regulator com posed by simple diodes due to its process, voltage and temperature (PVT), the transponder performance was measured with and without the shunt regulator enabled. Results show an improvement of 16.7 % in the communication distance between the transponder and the reader.Identificação por Rádio Frequência (RFID) é usada em muitas aplicações, colocando etiquetas eletrônicas em animais e objetos para facilitar a leitura a fim de melhorar o gerenciamento destes. Nesse contexto, essa dissertação tem como objetivo melhorar a regulação de potência em chips de RFID a fim de aumentar a distância de leitura. Essa dissertação apresenta um nova arquitetura de regulador paralelo, não linear, que usa um detector de potência de Rádio Frequência (RF) baseado em uma técnica de modulação de pulso (PWM) para aplicação de RFID que usam o princípio de comunicação por acopla mento magnético. A arquitetura de regulador proposto é composta de duas realimen tações: uma realimentação usa um limitador de tensão rápido e a outra usa um detector de potência lento porém preciso. O primeiro garante a proteção contra sobre tensão e o segundo corrige a imprecisão do primeiro de acordo com a potência do sinal de entrada. Primeiramente, o estado da arte em regulação de sitemas de RFID bem como em detectores de potência RF são feitos para contextualizar os problemas e melhorias da nova arquitetura. Um desenvolvimento teórico seguido por simulações elétricas e o projeto do circuito da nova arquitetura de regulador paralelo são abordadas em detalhes. A circuito foi implementado em um processo CMOS de 180 nm como parte de um Chip de RFID de baixa frequência (134 kHz). O regulador lida com uma tensão senoidal (134 kHz) na sua entrada, gerada por um tanque LC que extrai energia provinda do leitor e que é usada alimentar todo o chip. Devido ao uso de um processo padrão 3.3 V CMOS para implementação do circuitos analógicos a fim de diminuir o custo de fabricação com o não uso do modulo de alta tensão (Ex. 5 V), impondo dificuldades no projeto do sistema, mesmo assim a solução proposta regula a tensão de entrada do chip em 3.6 V, máxima suportada pela tecnologia, com o uso das duas malhas de realimentação. A área total do Chip de RFID é de 870x870 µm², com 130x230 µm² para apenas o circuito de regulação. Os capacitores de ressonância e de alimentação foram integrados no Chip. O sistema completo consome 4.5 µA, sobre uma ampla gama de potência de entrada que é modulada pela distância entre o leitor e a tag. Como o detector de potência corrige a imprecisão do limitador de tensão composto de diodos devido a variação em processo, tensão e temperatura (PVT), a distância de leitura foi medida com e sem o detector de potência habilitado. Os resultados mostraram uma melhoria de 16.7 % na distância de comunicação

RFID multiantenna systems for wireless communications and sensing

Many scientific, industrial and medical applications require the measurement of different physical parameters in order to collect information about the spatially distributed status of some process. Very often this information needs to be collected remotely, either due to the spatial dispersion of the measurement points or due to their inaccessibility. A wireless embedded self-powered sensor may be a convenient solution to be placed at these inaccessible locations. This thesis is devoted to study the analytical relation governing the electromagnetic coupling between a reader and a embeddable self-powered sensor, based on radio frequency identification (RFID) technology, which is capable of wirelessly retrieving the status of physical parameters at a remote and inaccessible location. The physical parameter to be sensed may be the electromagnetic (EM) field existing at that location (primary measurement) or the indirect measurement of other parameters such as the temperature, humidity, etc. (secondary measurement). Given the simplicity of the RFID solution (highly embeddable properties, scavenging capabilities, penetration and radio coverage characteristics, etc.) the measurement can be done at a single location, or it can be extended to a set of measuring locations (an array or grid of sensors). The analytical relation is based on a reciprocity formulation studying the modulation of the scattered field by the embedded sensor in relation with the incident field, and allows to define a set of quality parameters of interest for the optimum design of the sensors. Particular attention is given to the scavenging circuitry as well as to the antenna design relevant to the sensing objective. In RFID tags, the existence of an RF harvesting section is an improvement with respect to conventional scattering field probes since it removes the need of DC biasing lines or optical fibers to modulate the sensor. However, this harvesting section introduces non-linearities in the response of the sensor, which requires a proper correction to use them as EM-field probes, although the characterization of the non-linearities of the RFID tag cannot be directly done using a conventional vector network analyzer (VNA), due to the requirements of an RFID protocol excitation. Due to this, this thesis proposes an alternative measurement approach that allows to characterize the different scattering states used for the modulation, in particular its non-linear behavior. In addittion, and taking this characterization as the starting point, this thesis proposes a new measurement setup for EM-field measurements based on the use of multiple tones to enlarge the available dynamic range, which is experimentally demonstrated in the measurement of a radiation pattern, as well as in imaging applications. The RFID-based sensor response is electromagnetically sensitive to the dielectric properties of its close environment. However, the governing formulation for the response of the probe mixes together a set of different contributions, the path-loss, the antenna impedance, the loads impedance, etc. As a consequence, it is not possible to isolate each contribution from the others using the information available with a conventional RFID sensor. This thesis mathematically proposes and experimentally develops a modification of the modulation scheme to introduce a new set of multi-load scattering states that increases the information available in the response and properly isolate each term. Moreover, this thesis goes a step forward and introduces a new scattering state of the probe sensitive to temperature variations that do not depend on the environment characteristics. This new configuration enables robust environmental sensing in addition to EM-field measurements, and sensing variations of the dielectric properties of the environment

Sistemas eficientes de transmissão de energia sem-fios e identificação por radiofrequência

Doutoramento em Engenharia EletrotécnicaIn the IoT context, where billions of connected objects are expected to be ubiquitously deployed worldwide, the frequent battery maintenance of ubiquitous wireless nodes is undesirable or even impossible. In these scenarios, passive-backscatter radios will certainly play a crucial role due to their low cost, low complexity and battery-free operation. However, as passive-backscatter devices are chiefly limited by the WPT link, its efficiency optimization has been a major research concern over the years, gaining even more emphasis in the IoT context. Wireless power transfer has traditionally been carried out using CW signals, and the efficiency improvement has commonly been achieved through circuit design optimization. This thesis explores a fundamentally different approach, in which the optimization is focused on the powering waveforms, rather than the circuits. It is demonstrated through theoretical analysis, simulations and measurements that, given their greater ability to overcome the built-in voltage of rectifying devices, high PAPR multi-sine (MS) signals are capable of more efficiently exciting energy harvesting circuits when compared to CWs. By using optimal MS signals to excite rectifying devices, remarkable RF-DC conversion efficiency gains of up to 15 dB with respect to CW signals were obtained. In order to show the effectiveness of this approach to improve the communication range of passive-backscatter systems, a MS front-end was integrated in a commercial RFID reader and a significant range extension of 25% was observed. Furthermore, a software-defined radio RFID reader, compliant with ISO18000-6C standard and with MS capability, was constructed from scratch. By interrogating passive RFID transponders with MS waveforms, a transponder sensitivity improvement higher than 3 dB was obtained for optimal MS signals. Since the amplification and transmission of high PAPR signals is critical, this work also proposes efficient MS transmitting architectures based on space power combining techniques. This thesis also addresses other not less important issues, namely self-jamming in passive RFID readers, which is the second limiting factor of passive-backscatter systems. A suitable self-jamming suppression scheme was first used for CW signals and then extended to MS signals, yielding a CW isolation up to 50 dB and a MS isolation up 60 dB. Finally, a battery-less remote control system was developed and integrated in a commercial TV device with the purpose of demonstrating a practical application of wireless power transfer and passive-backscatter concepts. This allowed battery-free control of four basic functionalities of the TV (CH+,CH-,VOL+,VOL-).No contexto da internet das coisas (IoT), onde são esperados bilhões de objetos conectados espalhados pelo planeta de forma ubíqua, torna-se impraticável uma frequente manutenção e troca de baterias dos dispositivos sem fios ubíquos. Nestes cenários, os sistemas radio backscatter passivos terão um papel preponderante dado o seu baixo custo, baixa complexidade e não necessidade de baterias nos nós móveis. Uma vez que a transmissão de energia sem fios é o principal aspeto limitativo nestes sistemas, a sua otimização tem sido um tema central de investigação, ganhando ainda mais ênfase no contexto IoT. Tradicionalmente, a transferência de energia sem-fios é feita através de sinais CW e a maximização da eficiência é conseguida através da otimização dos circuitos recetores. Neste trabalho explora-se uma abordagem fundamentalmente diferente, em que a otimização foca-se nas formas de onda em vez dos circuitos. Demonstra-se, teoricamente e através de simulações e medidas que, devido à sua maior capacidade em superar a barreira de potencial intrínseca dos dispositivos retificadores, os sinais multi-seno (MS) de elevado PAPR são capazes de excitar os circuitos de colheita de energia de forma mais eficiente quando comparados com o sinal CW tradicional. Usando sinais MS ótimos em circuitos retificadores, foram verificadas experimentalmente melhorias de eficiência de conversão RF-DC notáveis de até 15 dB relativamente ao sinal CW. A fim de mostrar a eficácia desta abordagem na melhoria da distância de comunicação de sistemas backscatter passivos, integrou-se um front-end MS num leitor RFID comercial e observou-se um aumento significativo de 25% na distância de leitura. Além disso, desenvolveu-se de raiz um leitor RFID baseado em software rádio, compatível com o protocolo ISO18000-6C e capaz de gerar sinais MS, com os quais interrogou-se transponders passivos, obtendo-se ganhos de sensibilidade dos transponders maiores que 3 dB. Uma vez que a amplificação de sinais de elevado PAPR é uma operação crítica, propôs-se também novas arquiteturas eficientes de transmissão baseadas na combinação de sinais em espaço livre. Esta tese aborda também outros aspetos não menos importantes, como o self-jamming em leitores RFID passivos, tido como o segundo fator limitativo neste tipo de sistemas. Estudou-se técnicas de cancelamento de self-jamming CW e estendeu-se o conceito a sinais MS, tendo-se obtido isolamentos entre o transmissor e o recetor de até 50 dB no primeiro caso e de até 60 dB no segundo. Finalmente, com o objetivo de demonstrar uma aplicação prática dos conceitos de transmissão de energia sem fios e comunicação backscatter, desenvolveu-se um sistema de controlo remoto sem pilhas, cujo protótipo foi integrado num televisor comercial a fim de controlar quatro funcionalidades básicas (CH+,CH-,VOL+,VOL-)

Low-power CMOS rectifier and Chien search design for RFID tags

Automotive sensors implemented in radio frequency identification (RFID) tags can correct data errors by using BCH (Bose-Chaudhuri-Hocquenghem) decoder, for which Chien search is a computation-intensive key step. Existing low power approaches have drastically degrading performance for multiple-bit-correcting codes. This thesis presents a novel approach of using register-transfer-level (RTL) power management in the search process, leading to significant power savings for BCH codes with higher correction capability. An example for the (255, 187, 9) BCH code has been implemented in 0.18μm CMOS technology. We also consider ways of conserving power for the sole power harvester on a passive tag – the rectifier. With ST CMOS 90nm technology, a three-stage differential-drive CMOS rectifier is designed by using a new transistor scaling method and a piece-wise linear matching technique. For the standard 915MHz band, simulation indicates high power conversion efficiency (PCE) of 74% and a significantly increased output power of 30.3μW at 10 meters