3,266 research outputs found
Comparison of large-angle production of charged pions with incident protons on cylindrical long and short targets
The HARP collaboration has presented measurements of the double-differential
pi+/pi- production cross-section in the range of momentum 100 MeV/c <= p 800
MeV/c and angle 0.35 rad <= theta <= 2.15 rad with proton beams hitting thin
nuclear targets. In many applications the extrapolation to long targets is
necessary. In this paper the analysis of data taken with long (one interaction
length) solid cylindrical targets made of carbon, tantalum and lead is
presented. The data were taken with the large acceptance HARP detector in the
T9 beam line of the CERN PS. The secondary pions were produced by beams of
protons with momenta 5 GeV/c, 8 GeV/c and 12 GeV/c. The tracking and
identification of the produced particles were performed using a small-radius
cylindrical time projection chamber (TPC) placed inside a solenoidal magnet.
Incident protons were identified by an elaborate system of beam detectors.
Results are obtained for the double-differential yields per target nucleon d2
sigma / dp dtheta. The measurements are compared with predictions of the MARS
and GEANT4 Monte Carlo simulations.Comment: 43 pages, 20 figure
Forward production of charged pions with incident on nuclear targets measured at the CERN PS
Measurements of the double-differential production cross-section
in the range of momentum 0.5 \GeVc \leq p \le 8.0 \GeVc and angle 0.025 \rad
\leq \theta \le 0.25 \rad in interactions of charged pions on beryllium,
carbon, aluminium, copper, tin, tantalum and lead are presented. These data
represent the first experimental campaign to systematically measure forward
pion hadroproduction. The data were taken with the large acceptance HARP
detector in the T9 beam line of the CERN PS. Incident particles, impinging on a
5% nuclear interaction length target, were identified by an elaborate system of
beam detectors. The tracking and identification of the produced particles was
performed using the forward spectrometer of the HARP detector. Results are
obtained for the double-differential cross-sections mainly at four incident pion beam
momenta (3 \GeVc, 5 \GeVc, 8 \GeVc and 12 \GeVc). The measurements are compared
with the GEANT4 and MARS Monte Carlo simulationComment: to be published on Nuclear Physics
Absolute Momentum Calibration of the HARP TPC
In the HARP experiment the large-angle spectrometer is using a cylindrical
TPC as main tracking and particle identification detector. The momentum scale
of reconstructed tracks in the TPC is the most important systematic error for
the majority of kinematic bins used for the HARP measurements of the
double-differential production cross-section of charged pions in proton
interactions on nuclear targets at large angle. The HARP TPC operated with a
number of hardware shortfalls and operational mistakes. Thus it was important
to control and characterize its momentum calibration. While it was not possible
to enter a direct particle beam into the sensitive volume of the TPC to
calibrate the detector, a set of physical processes and detector properties
were exploited to achieve a precise calibration of the apparatus. In the
following we recall the main issues concerning the momentum measurement in the
HARP TPC, and describe the cross-checks made to validate the momentum scale. As
a conclusion, this analysis demonstrates that the measurement of momentum is
correct within the published precision of 3%.Comment: To be published by JINS
Measurement of the production of charged pions by protons on a tantalum target
A measurement of the double-differential cross-section for the production of
charged pions in proton--tantalum collisions emitted at large angles from the
incoming beam direction is presented. The data were taken in 2002 with the HARP
detector in the T9 beam line of the CERN PS. The pions were produced by proton
beams in a momentum range from 3 \GeVc to 12 \GeVc hitting a tantalum target
with a thickness of 5% of a nuclear interaction length. The angular and
momentum range covered by the experiment (100 \MeVc \le p < 800 \MeVc and
0.35 \rad \le \theta <2.15 \rad) is of particular importance for the design
of a neutrino factory. The produced particles were detected using a
small-radius cylindrical time projection chamber (TPC) placed in a solenoidal
magnet. Track recognition, momentum determination and particle identification
were all performed based on the measurements made with the TPC. An elaborate
system of detectors in the beam line ensured the identification of the incident
particles. Results are shown for the double-differential cross-sections
at four incident
proton beam momenta (3 \GeVc, 5 \GeVc, 8 \GeVc and 12 \GeVc). In addition, the
pion yields within the acceptance of typical neutrino factory designs are shown
as a function of beam momentum. The measurement of these yields within a single
experiment eliminates most systematic errors in the comparison between rates at
different beam momenta and between positive and negative pion production.Comment: 49 pages, 31 figures. Version accepted for publication on Eur. Phys.
J.
Large-angle production of charged pions by 3 GeV/c - 12 GeV/c protons on carbon, copper and tin targets
A measurement of the double-differential production cross-section
in proton--carbon, proton--copper and proton--tin collisions in the range of
pion momentum 100 \MeVc \leq p < 800 \MeVc and angle 0.35 \rad \le \theta
<2.15 \rad is presented. The data were taken with the HARP detector in the T9
beam line of the CERN PS. The pions were produced by proton beams in a momentum
range from 3 \GeVc to 12 \GeVc hitting a target with a thickness of 5% of a
nuclear interaction length. The tracking and identification of the produced
particles was done using a small-radius cylindrical time projection chamber
(TPC) placed in a solenoidal magnet. An elaborate system of detectors in the
beam line ensured the identification of the incident particles. Results are
shown for the double-differential cross-sections at four incident proton beam
momenta (3 \GeVc, 5 \GeVc, 8 \GeVc and 12 \GeVc)
System Test of the ATLAS Muon Spectrometer in the H8 Beam at the CERN SPS
An extensive system test of the ATLAS muon spectrometer has been performed in
the H8 beam line at the CERN SPS during the last four years. This spectrometer
will use pressurized Monitored Drift Tube (MDT) chambers and Cathode Strip
Chambers (CSC) for precision tracking, Resistive Plate Chambers (RPCs) for
triggering in the barrel and Thin Gap Chambers (TGCs) for triggering in the
end-cap region. The test set-up emulates one projective tower of the barrel
(six MDT chambers and six RPCs) and one end-cap octant (six MDT chambers, A CSC
and three TGCs). The barrel and end-cap stands have also been equipped with
optical alignment systems, aiming at a relative positioning of the precision
chambers in each tower to 30-40 micrometers. In addition to the performance of
the detectors and the alignment scheme, many other systems aspects of the ATLAS
muon spectrometer have been tested and validated with this setup, such as the
mechanical detector integration and installation, the detector control system,
the data acquisition, high level trigger software and off-line event
reconstruction. Measurements with muon energies ranging from 20 to 300 GeV have
allowed measuring the trigger and tracking performance of this set-up, in a
configuration very similar to the final spectrometer. A special bunched muon
beam with 25 ns bunch spacing, emulating the LHC bunch structure, has been used
to study the timing resolution and bunch identification performance of the
trigger chambers. The ATLAS first-level trigger chain has been operated with
muon trigger signals for the first time
Large-angle production of charged pions by 3 GeV/c - 12.9 GeV/c protons on beryllium, aluminium and lead targets
Measurements of the double-differential production cross-section
in the range of momentum 100 \MeVc \leq p < 800 \MeVc and angle 0.35 \rad
\leq \theta < 2.15 \rad in proton--beryllium, proton--aluminium and
proton--lead collisions are presented. The data were taken with the HARP
detector in the T9 beam line of the CERN PS. The pions were produced by proton
beams in a momentum range from 3 \GeVc to 12.9 \GeVc hitting a target with a
thickness of 5% of a nuclear interaction length. The tracking and
identification of the produced particles was performed using a small-radius
cylindrical time projection chamber (TPC) placed inside a solenoidal magnet.
Incident particles were identified by an elaborate system of beam detectors.
Results are obtained for the double-differential cross-sections at six incident
proton beam momenta (3 \GeVc, 5 \GeVc, 8 \GeVc, 8.9 \GeVc (Be only), 12 \GeVc
and 12.9 \GeVc (Al only)) and compared to previously available data
Measurement of the production cross-section of positive pions in the collision of 8.9 GeV/c protons on beryllium
The double-differential production cross-section of positive pions,
, measured in the HARP experiment is presented.
The incident particles are 8.9 GeV/c protons directed onto a beryllium target
with a nominal thickness of 5% of a nuclear interaction length. The measured
cross-section has a direct impact on the prediction of neutrino fluxes for the
MiniBooNE and SciBooNE experiments at Fermilab. After cuts, 13 million protons
on target produced about 96,000 reconstructed secondary tracks which were used
in this analysis. Cross-section results are presented in the kinematic range
0.75 GeV/c < < 6.5 GeV/c and 30 mrad < < 210 mrad in
the laboratory frame.Comment: 39 pages, 21 figures. Version accepted for publication by Eur. Phys.
J.
MICE: the Muon Ionization Cooling Experiment. Step I: First Measurement of Emittance with Particle Physics Detectors
The Muon Ionization Cooling Experiment (MICE) is a strategic R&D project intended to demonstrate the only practical solution to providing high brilliance beams necessary for a neutrino factory or muon collider. MICE is under development at the Rutherford Appleton Laboratory (RAL) in the United Kingdom. It comprises a dedicated beamline to generate a range of input muon emittances and momenta, with time-of-flight and Cherenkov detectors to ensure a pure muon beam. The emittance of the incoming beam will be measured in the upstream magnetic spectrometer with a scintillating fiber tracker. A cooling cell will then follow, alternating energy loss in Liquid Hydrogen (LH2) absorbers to RF cavity acceleration. A second spectrometer, identical to the first, and a second muon identification system will measure the outgoing emittance. In the 2010 run at RAL the muon beamline and most detectors were fully commissioned and a first measurement of the emittance of the muon beam with particle physics (time-of-flight) detectors was performed. The analysis of these data was recently completed and is discussed in this paper. Future steps for MICE, where beam emittance and emittance reduction (cooling) are to be measured with greater accuracy, are also presented
Search for the exotic resonance in the NOMAD experiment
A search for exotic Theta baryon via Theta -> proton +Ks decay mode in the
NOMAD muon neutrino DIS data is reported. The special background generation
procedure was developed. The proton identification criteria are tuned to
maximize the sensitivity to the Theta signal as a function of xF which allows
to study the Theta production mechanism. We do not observe any evidence for the
Theta state in the NOMAD data. We provide an upper limit on Theta production
rate at 90% CL as 2.13 per 1000 of neutrino interactions.Comment: Accepted to European Physics Journal
- …