Research and development of an air-puff excitation system for lightweight structures

© 2019 International Group of Operational Modal Analysis. Lightweight, thin-walled structures appear in numerous engineering and natural structures. Due to their sensitivity, vibration excitation by, now traditional, contacting techniques, such as modally-tuned impact hammers or electrodynamic shakers, to investigate their dynamics is challenging since it typically adds substantial mass and/or stiffness at the excitation location. The research presented in this article, therefore, is intended to yield a system for the non-contact excitation of thin-walled structures through small, controlled blasts of air. An air-puff system, consisting of two fast-acting solenoid-controlled valves, a small air outlet nozzle and bespoke control software with a programmable valve control sequence, is researched and developed. The excitation impulse characteristics are investigated experimentally and described in detail for varying input control parameters. Ultimately, suitability of the system for the excitation of thin-walled structures is explored, for both a 3D-printed micro-satellite panel and a natural bee honeycomb, with promising results when compared to that of an impact hammer

Mediolateral Damping of an Overhead Body Weight Support System Assists Stability During Treadmill Walking

Background Body weight support systems with three or more degrees of freedom (3-DoF) are permissive and safe environments that provide unloading and allow unrestricted movement in any direction. This enables training of walking and balance control at an early stage in rehabilitation. Transparent systems generate a support force vector that is near vertical at all positions in the workspace to only minimally interfere with natural movement patterns. Patients with impaired balance, however, may benefit from additional mediolateral support that can be adjusted according to their capacity. An elegant solution for providing balance support might be by rendering viscous damping along the mediolateral axis via the software controller. Before use with patients, we evaluated if control-rendered mediolateral damping evokes the desired stability enhancement in able-bodied individuals. Methods A transparent, cable-driven robotic body weight support system (FLOAT) was used to provide transparent body weight support with and without mediolateral damping to 21 able-bodied volunteers while walking at preferred gait velocity on a treadmill. Stability metrics reflecting resistance to small and large perturbations were derived from walking kinematics and compared between conditions and to free walking. Results Compared to free walking, the application of body weight support per-se resulted in gait alterations typically associated with body weight support, namely increased step length and swing phase. Frontal plane dynamic stability, measured by kinematic variability and nonlinear dynamics of the center of mass, was increased under body weight support, indicating reduced balance requirements in both damped and undamped support conditions. Adding damping to the body weight support resulted in a greater increase of frontal plane stability. Conclusion Adding mediolateral damping to 3-DoF body weight support systems is an effective method of increasing frontal plane stability during walking in able-bodied participants. Building on these results, adjustable mediolateral damping could enable therapists to select combinations of unloading and stability specifically for each patient and to adapt this in a task specific manner. This could extend the impact of transparent 3-DoF body weight support systems, enabling training of gait and active balance from an early time point onwards in the rehabilitation process for a wide range of mobility activities of daily life

Coupling rheology and segregation in granular flows

During the last fifteen years there has been a paradigm shift in the continuum modelling of granular materials; most notably with the development of rheological models, such as the μ(I) μ(I) -rheology (where μ μ is the friction and I is the inertial number), but also with significant advances in theories for particle segregation. This paper details theoretical and numerical frameworks (based on OpenFOAM) which unify these currently disconnected endeavours. Coupling the segregation with the flow, and vice versa, is not only vital for a complete theory of granular materials, but is also beneficial for developing numerical methods to handle evolving free surfaces. This general approach is based on the partially regularized incompressible μ(I) μ(I) -rheology, which is coupled to the gravity-driven segregation theory of Gray & Ancey (J. Fluid Mech., vol. 678, 2011, pp. 353–588). These advection–diffusion–segregation equations describe the evolving concentrations of the constituents, which then couple back to the variable viscosity in the incompressible Navier–Stokes equations. A novel feature of this approach is that any number of differently sized phases may be included, which may have disparate frictional properties. Further inclusion of an excess air phase, which segregates away from the granular material, then allows the complex evolution of the free surface to be captured simultaneously. Three primary coupling mechanisms are identified: (i) advection of the particle concentrations by the bulk velocity, (ii) feedback of the particle-size and/or frictional properties on the bulk flow field and (iii) influence of the shear rate, pressure, gravity, particle size and particle-size ratio on the locally evolving segregation and diffusion rates. The numerical method is extensively tested in one-way coupled computations, before the fully coupled model is compared with the discrete element method simulations of Tripathi & Khakhar (Phys. Fluids, vol. 23, 2011, 113302) and used to compute the petal-like segregation pattern that spontaneously develops in a square rotating drum

Synthesis, surface active and antimicrobial properties of new alkyl 2,6-dideoxy-L-arabino-hexopyranosides

Synthesis of alkyl 2,6-dideoxy-L-arabino-hexopyranosides was accomplished by the reaction of 1,5-anhydro-2,6-dideoxy-L-arabino-hex-1-enitol with fatty alcohols in dichloromethane, catalyzed by triphenylphosphine hydrobromide. Reaction with octanol and dodecanol gave the corresponding α-glycosides in 50% and 42% yield, the β-glycosides in 20% and 21% yield and the α-anomer of the Ferrier product in 10% and 9% yield, respectively.Deacetylation of the α-/β-glycosides with sodium methoxide in methanol afforded the amphiphilic L-arabino-hexopyranosides in 94–99% yield. The surface tension at the air–water interface of the octyl L-glycosides and of the dodecyl α-L-glycoside aqueous solutions at 35 °C was measured with a du Noüy ring tensiometer and surface properties such as critical micelle concentration (CMC), relative surface excess, molecular area at the interface and Gibbs micellization free energy were evaluated. The stereochemistry of the hexopyranoside ring in unimers and aggregates is correlated to the hydrophobicity and packing efficiency on the air–water interface. The antibacterial and antifungal activities of the surface-active glycosides were evaluated using the paper disk diffusion method. The dodecyl α-L-arabino-hexopyranoside was quite active over Bacillus cereus and Bacillus subtilis, while low activity was found for this glycoside over Enterococcus faecalis and Listeria monocytogenes. The octyl glycosides tested showed low activity over almost all the above-mentioned bacteria, and also over the fungus Candida albicans. No inhibition of Salmonella enteritidis and of the filamentous fungus Aspergillus niger was detected for any of the compounds tested.info:eu-repo/semantics/publishedVersio

Health promoting potential of herbal teas and tinctures from Artemisia campestris subsp maritima: from traditional remedies to prospective products

This work explored the biotechnological potential of the medicinal halophyte Artemisia campestris subsp. maritima (dune wormwood) as a source of health promoting commodities. For that purpose, infusions, decoctions and tinctures were prepared from roots and aerial-organs and evaluated for in vitro antioxidant, anti-diabetic and tyrosinase-inhibitory potential, and also for polyphenolic and mineral contents and toxicity. The dune wormwood extracts had high polyphenolic content and several phenolics were identified by ultra-high performance liquid chromatography-photodiode array-mass-spectrometry (UHPLC-PDA-MS). The main compounds were quinic, chlorogenic and caffeic acids, coumarin sulfates and dicaffeoylquinic acids; several of the identified phytoconstituents are here firstly reported in this A. campestris subspecies. Results obtained with this plant's extracts point to nutritional applications as mineral supplementary source, safe for human consumption, as suggested by the moderate to low toxicity of the extracts towards mammalian cell lines. The dune wormwood extracts had in general high antioxidant activity and also the capacity to inhibit a-glucosidase and tyrosinase. In summary, dune wormwood extracts are a significant source of polyphenolic and mineral constituents, antioxidants and a-glucosidase and tyrosinase inhibitors, and thus, relevant for different commercial segments like the pharmaceutical, cosmetic and/or food industries.FCT - Foundation for Science and Technology [CCMAR/Multi/04326/2013]; Portuguese National Budget; FCT [IF/00049/2012, SFRH/BD/94407/2013]; Research Foundation - Flanders (FWO) [12M8315N]info:eu-repo/semantics/publishedVersio

Local Hadronic Calibration

The scheme of the hadronic calibration is discussed. Based on the cluster reconstruction an effective noise suppression is achieved. In a first step clusters are classified as electromagnetic or hadronic clusters. The weighting scheme to correct for the different e/pion response in the ATLAS calorimeter is presented. Dead material corrections and out of cluster corrections yield finally a signal which is rather close to the energy deposited by the final state particles in the ATLAS calorimeter. The constants and algorithms are derived from single pion MC studies and tested with jets. The validation of the scheme using testbeam data is presented as well

Detection of Borrelia-specific 16S rRNA sequence in total RNA extracted from Ixodes ricinus ticks

A reverse transcriptase - polymerase chain reaction based assay for Borrelia species detection in ticks was developed. The method was based on amplification of 552 nucleotide bases long sequence of 16S rRNA, targeted by Borrelia specific primers. In the present study, total RNA extracted from Ixodes ricinus ticks was used as template. The results showed higher sensitivity for Borrelia detection as compared to standard dark-field microscopy. Method specificity was confirmed by cloning and sequencing of obtained 552 base pairs long amplicons. Phylogenetic analysis of obtained sequences showed that they belong to B. lusitaniae and B. afzelii genospecies. RT-PCR based method presented in this paper could be very useful as a screening test for detecting pathogen presence, especially when in investigations is required extraction of total RNA from ticks

Standalone vertex finding in the ATLAS muon spectrometer

A dedicated reconstruction algorithm to find decay vertices in the ATLAS muon spectrometer is presented. The algorithm searches the region just upstream of or inside the muon spectrometer volume for multi-particle vertices that originate from the decay of particles with long decay paths. The performance of the algorithm is evaluated using both a sample of simulated Higgs boson events, in which the Higgs boson decays to long-lived neutral particles that in turn decay to bbar b final states, and pp collision data at √s = 7 TeV collected with the ATLAS detector at the LHC during 2011