Catalytic behavior of chromium oxide supported on nanocasting-prepared mesoporous alumina in dehydrogenation of propane

Mesoporous alumina with narrow pore size distribution centered in the range of 4.4–5.0 nm and with a specific surface area as high as 270 m2·g−1 was prepared via the nanocasting approach using a CMK-3 carbon replica as a hard template. Based on this support, a series of catalysts containing 1, 5, 10, 20 and 30 wt % of chromium was prepared by incipient wetness impregnation, characterized, and studied in the dehydrogenation of propane to propene (PDH). Cr species in three oxidation states—Cr(III), Cr(V) and Cr(VI)—were found on the oxidized surface of the catalysts. The concentration of these species varied with the total Cr loading. Temperature-programmed reduction (H2-TPR) and UV-Vis diffuse reflectance spectroscopy (UV-Vis-DRS) studies revealed that Cr(VI) species dominated at the lowest Cr content. An increase in the Cr loading resulted in an appearance of an increasing amount of Cr(III) oxide. UV-Vis-DRS measurements performed in situ during the PDH process showed that at the beginning of the catalytic test Cr(VI) species were reduced to Cr(III) redox species. A crucial role of the redox species in the PDH process over the catalysts with the low Cr content was confirmed. The stability test for the catalyst containing 20 wt % of Cr showed that this sample exhibited the reproducible catalytic performance after the first four regeneration–dehydrogenation cycles. Moreover, this catalyst had higher resistance on deactivation during the PDH process as compared to the reference catalyst with the same Cr loading, but was supported on commercially available alumina

Interplay Between Bromine and Iodine in Oxidative Dehydrogenation

Oxidative dehydrogenation is a promising way to produce olefins, diolefins and aromatics. However, the product yield is limited by the consecutive oxidation of the product to oxygenated products. The highest yield reported for propane oxidative dehydrogenation is only about 30%. Alternatively, halogens can be used as oxidants in oxidative dehydrogenations. Although the iodine process is highly selective, it requires very high reaction temperatures (≈900K) to give a good yield of C3H6+C3H7I, and iodine is too expensive for industrial deployment. Bromine is a more reactive oxidant but less selective towards C3H6 and C3H7Br. We show that the use of bromine-iodine mixtures with low iodine content (no greater than 20%) results in up to 80% of C3H6+C3H7X single-pass yield at moderate reaction temperatures (<800K). The results are promising for developing a low temperature on-purpose propylene technology. Furthermore, the underlying chemistry might be extended to the synthesis of many other commercially desirable unsaturated hydrocarbons. © 2013 WILEY-VCH Verlag GmbH & Co

Catalytic cracking of naphtha: The effect of Fe and Cr impregnated ZSM-5 on olefin selectivity

This study focuses on the modification of ZSM-5 in order to enhance the catalytic cracking of refinery naphtha to produce light olefins. ZSM-5 was metal modified using different loadings (0.5–5 wt%) of Fe and Cr via the impregnation method. The metal modified ZSM-5 samples are compared and the effect of metal loading on the physicochemical properties and catalytic performance is investigated. Fe and Cr modification had an effect on both the physicochemical properties of the catalysts as well as catalytic activity and selectivity. Metal loading caused a decrease in the specific surface area which decreased further with increased metal loading. Fe had a greater effect on the total acidity in particular strong acid sites when compared to Cr. The optimum Fe loading was established which promoted selectivity to olefins, in particular propylene. Fe also had a dominant effect on the P/E ratio of which a remarkable ratio of five was achieved as well as enhanced the stability of the catalyst. Cr was found to be a good promoter for selectivity to BTX products with a two-fold increase observed when compared to Fe-modified catalysts

Additive manufacturing: unlocking the evolution of energy materials

The global energy infrastructure is undergoing a drastic transformation towards renewable energy, posing huge challenges on the energy materials research, development and manufacturing. Additive manufacturing has shown its promise to change the way how future energy system can be designed and delivered. It offers capability in manufacturing complex 3D structures, with near-complete design freedom and high sustainability due to minimal use of materials and toxic chemicals. Recent literatures have reported that additive manufacturing could unlock the evolution of energy materials and chemistries with unprecedented performance in the way that could never be achieved by conventional manufacturing techniques. This comprehensive review will fill the gap in communicating on recent breakthroughs in additive manufacturing for energy material and device applications. It will underpin the discoveries on what 3D functional energy structures can be created without design constraints, which bespoke energy materials could be additively manufactured with customised solutions, and how the additively manufactured devices could be integrated into energy systems. This review will also highlight emerging and important applications in energy additive manufacturing, including fuel cells, batteries, hydrogen, solar cell as well as carbon capture and storage

Harmonised statistics and maps of forest biomass and increment in Europe.

peer reviewedForest biomass is an essential resource in relation to the green transition and its assessment is key for the sustainable management of forest resources. Here, we present a forest biomass dataset for Europe based on the best available inventory and satellite data, with a higher level of harmonisation and spatial resolution than other existing data. This database provides statistics and maps of the forest area, biomass stock and their share available for wood supply in the year 2020, and statistics on gross and net volume increment in 2010-2020, for 38 European countries. The statistics of most countries are available at a sub-national scale and are derived from National Forest Inventory data, harmonised using common reference definitions and estimation methodology, and updated to a common year using a modelling approach. For those counties without harmonised statistics, data were derived from the State of Europe's Forest 2020 Report at the national scale. The maps are coherent with the statistics and depict the spatial distribution of the forest variables at 100 m resolution