POLITICAL ELECTIONS FOR MARKETERS

SrFe12O19 coatings, intended as electromagnetic wave absorbers, were produced by atmospheric plasma spraying (APS) using two different kindsof feedstock powders: spray-dried agglomerates of micrometric SrFe12O19 particles (type-A) or spray-dried agglomerates of raw materials (SrCO3,Fe2O3), reactively sintered at 1100 ◦C (type-B).During spraying, type-A agglomerates either remain unmelted, producing porous coating regions where crystalline hexaferrite is retained, orare disrupted into smaller granules which melt completely, resulting in dense coating regions with no crystalline hexaferrite.The sintered type-B agglomerates possess higher cohesive strength and do not fall apart: the finer ones melt completely, whereas, in the largerones, the outer region melts and infiltrates the porous unmelted core which retains crystalline hexaferrite. Dense coatings can therefore be obtainedwhile preserving high amounts of crystalline hexaferrite even inside the dense areas. Such coatings show magnetic properties that are promisingfor electromagnetic wave absorption applications

Synthesis, structural and magnetic properties of Y1-xYbxF3 solid solution

Many works devoted to obtaining nanodispersed BaTiO3 powder modified with different dopants for suitable properties providing. In particular, recently considerable attention has been given to obtaining modified nanopowders BaTiO3 possessing relaxor behavior order to ensure reliable work of dielectrics. Generally, Ca,Zr,Mn, ,Pb and rare earth elements such as Nb,Y adds order to provide stress, inhibit grain growth and provide Pinching effect, and hence to increase dielectrics relaxor behavior. However, there is still an issue associated with obtaining satisfactory stoichiometry of the obtained powder. From this viewpoint Ca,Zr-doped BaTiO3 were prepared with co-precipitation method via multiligand complexes formation and influence of the precursor type on Ca,Zr-doped BaTiO3 stoichiometry were investigated. Their stoichiometry, crystal structure was examined in order to determine preferential solubility site of Ca,Zr ions in perovskite structure. Stoichiometry Ca,Zr-modified BaTiO3 will be evaluated considering different precursor type. X-ray, IR spectroscopy and X-ray fluorescence analysis were carried out to obtain the knowledge on the occupation site in the Ba1-xСaxTi1-yZryO3 perovskite structure. These results proved influence complex formation on Ca,Zr-modified BaTiO3 stoichiometry

PZT-NZF/CF ferrite flexible thick films: Structural, dielectric, ferroelectric, and magnetic characterization

The preparation and properties of thick flexible three-phase composite films based on lead zirconium titanate (PZT) and various ferrites (nickel zinc ferrite (NZF) and cobalt ferrite (CF)) were reported in this study. Properties of three-phase composite films were compared with pure polyvinylidene fluoride (PVDF) and PZT-PVDF films. X-ray diffraction data indicated the formation of well crystallized structure of PZT and NZF/CF phases, without the presence of undesirable phases. Scanning electron micrographs showed that the ceramic particles were dispersed homogeneously in the PVDF matrix and atomic force microscopy confirmed that the size of the particles is around 30 nm. Non-saturated hysteresis loops were evident in all samples due to the presence of highly conductive ferrite phases. Under magnetic field of 10 kOe, composite films exhibited a typical ferromagnetic response. Dielectric properties were investigated in the temperature range from -128 to 250 degrees C and frequency range of 400 Hz-1 MHz. The results showed that the value of dielectric constant of the PVDF/PZT/ferrite composites increased about 25% above the one obtained for pure PVDF

Markov Properties of Electrical Discharge Current Fluctuations in Plasma

Using the Markovian method, we study the stochastic nature of electrical discharge current fluctuations in the Helium plasma. Sinusoidal trends are extracted from the data set by the Fourier-Detrended Fluctuation analysis and consequently cleaned data is retrieved. We determine the Markov time scale of the detrended data set by using likelihood analysis. We also estimate the Kramers-Moyal's coefficients of the discharge current fluctuations and derive the corresponding Fokker-Planck equation. In addition, the obtained Langevin equation enables us to reconstruct discharge time series with similar statistical properties compared with the observed in the experiment. We also provide an exact decomposition of temporal correlation function by using Kramers-Moyal's coefficients. We show that for the stationary time series, the two point temporal correlation function has an exponential decaying behavior with a characteristic correlation time scale. Our results confirm that, there is no definite relation between correlation and Markov time scales. However both of them behave as monotonic increasing function of discharge current intensity. Finally to complete our analysis, the multifractal behavior of reconstructed time series using its Keramers-Moyal's coefficients and original data set are investigated. Extended self similarity analysis demonstrates that fluctuations in our experimental setup deviates from Kolmogorov (K41) theory for fully developed turbulence regime.Comment: 25 pages, 9 figures and 4 tables. V3: Added comments, references, figures and major correction

Synthesis and characterization of ZnO nanostructures using palm olein as biotemplate

Background: A green approach to synthesize nanomaterials using biotemplates has been subjected to intense research due to several advantages. Palm olein as a biotemplate offers the benefits of eco-friendliness, low-cost and scale-up for large scale production. Therefore, the effect of palm olein on morphology and surface properties of ZnO nanostructures were investigated. Results: The results indicate that palm olein as a biotemplate can be used to modify the shape and size of ZnO particles synthesized by hydrothermal method. Different morphology including flake-, flower- and three dimensional star-like structures were obtained. FTIR study indicated the reaction between carboxyl group of palm olein and zinc species had taken place. Specific surface area enhanced while no considerable change were observed in optical properties. Conclusion: Phase-pure ZnO particles were successfully synthesized using palm olein as soft biotemplating agent by hydrothermal method. The physico-chemical properties of the resulting ZnO particles can be tuned using the ratio of palm olein to Zn cation

Overview of the TCV tokamak experimental programme

The tokamak a configuration variable (TCV) continues to leverage its unique shaping capabilities, flexible heating systems and modern control system to address critical issues in preparation for ITER and a fusion power plant. For the 2019-20 campaign its configurational flexibility has been enhanced with the installation of removable divertor gas baffles, its diagnostic capabilities with an extensive set of upgrades and its heating systems with new dual frequency gyrotrons. The gas baffles reduce coupling between the divertor and the main chamber and allow for detailed investigations on the role of fuelling in general and, together with upgraded boundary diagnostics, test divertor and edge models in particular. The increased heating capabilities broaden the operational regime to include T (e)/T (i) similar to 1 and have stimulated refocussing studies from L-mode to H-mode across a range of research topics. ITER baseline parameters were reached in type-I ELMy H-modes and alternative regimes with \u27small\u27 (or no) ELMs explored. Most prominently, negative triangularity was investigated in detail and confirmed as an attractive scenario with H-mode level core confinement but an L-mode edge. Emphasis was also placed on control, where an increased number of observers, actuators and control solutions became available and are now integrated into a generic control framework as will be needed in future devices. The quantity and quality of results of the 2019-20 TCV campaign are a testament to its successful integration within the European research effort alongside a vibrant domestic programme and international collaborations

Operating a full tungsten actively cooled tokamak: overview of WEST first phase of operation

WEST is an MA class superconducting, actively cooled, full tungsten (W) tokamak, designed to operate in long pulses up to 1000 s. In support of ITER operation and DEMO conceptual activities, key missions of WEST are: (i) qualification of high heat flux plasma-facing components in integrating both technological and physics aspects in relevant heat and particle exhaust conditions, particularly for the tungsten monoblocks foreseen in ITER divertor; (ii) integrated steady-state operation at high confinement, with a focus on power exhaust issues. During the phase 1 of operation (2017–2020), a set of actively cooled ITER-grade plasma facing unit prototypes was integrated into the inertially cooled W coated startup lower divertor. Up to 8.8 MW of RF power has been coupled to the plasma and divertor heat flux of up to 6 MW m−2 were reached. Long pulse operation was started, using the upper actively cooled divertor, with a discharge of about 1 min achieved. This paper gives an overview of the results achieved in phase 1. Perspectives for phase 2, operating with the full capability of the device with the complete ITER-grade actively cooled lower divertor, are also described

Physics research on the TCV tokamak facility: from conventional to alternative scenarios and beyond

The research program of the TCV tokamak ranges from conventional to advanced-tokamak scenarios and alternative divertor configurations, to exploratory plasmas driven by theoretical insight, exploiting the device’s unique shaping capabilities. Disruption avoidance by real-time locked mode prevention or unlocking with electron-cyclotron resonance heating (ECRH) was thoroughly documented, using magnetic and radiation triggers. Runaway generation with high-Z noble-gas injection and runaway dissipation by subsequent Ne or Ar injection were studied for model validation. The new 1 MW neutral beam injector has expanded the parameter range, now encompassing ELMy H-modes in an ITER-like shape and nearly non-inductive H-mode discharges sustained by electron cyclotron and neutral beam current drive. In the H-mode, the pedestal pressure increases modestly with nitrogen seeding while fueling moves the density pedestal outwards, but the plasma stored energy is largely uncorrelated to either seeding or fueling. High fueling at high triangularity is key to accessing the attractive small edge-localized mode (type-II) regime. Turbulence is reduced in the core at negative triangularity, consistent with increased confinement and in accord with global gyrokinetic simulations. The geodesic acoustic mode, possibly coupled with avalanche events, has been linked with particle flow to the wall in diverted plasmas. Detachment, scrape-off layer transport, and turbulence were studied in L- and H-modes in both standard and alternative configurations (snowflake, super-X, and beyond). The detachment process is caused by power ‘starvation’ reducing the ionization source, with volume recombination playing only a minor role. Partial detachment in the H-mode is obtained with impurity seeding and has shown little dependence on flux expansion in standard single-null geometry. In the attached L-mode phase, increasing the outer connection length reduces the in–out heat-flow asymmetry. A doublet plasma, featuring an internal X-point, was achieved successfully, and a transport barrier was observed in the mantle just outside the internal separatrix. In the near future variable-configuration baffles and possibly divertor pumping will be introduced to investigate the effect of divertor closure on exhaust and performance, and 3.5 MW ECRH and 1 MW neutral beam injection heating will be added

Magnetic polydomain liquid crystal elastomers–synthesis and characterisation

Although liquid crystal elastomers (LCE) are a fascinating class of materials with interesting thermomechanical properties of their own, the aim is to enhance their performance or add new features, e.g. response to external stimuli. The generally weak response of organic materials can be significantly intensified by mixing nano-sized magnetic particles into the host polymer matrix. An alternative approach is chemically coupling the nanoparticles to the elastomer. We achieved this by bonding functionalised magnetic nanoplatelets to the backbone of a main-chain LCE and obtained polydomain magnetic liquid crystal elastomers. We measured the magnetisation curves in samples, which were exposed to either small or large magnetic fields–their response being a consequence of partial particle reorientation or magnetic moment flipping. In contrast to the samples, which were exposed to small magnetic field and in which the remanent magnetisation can be reset to zero by heating the sample, the samples with flipped magnetisation within the platelets cannot be reversed into the original state. Coupling of magnetic and mechanical properties shows a slight magneto-elastic response at elevated temperatures and a significant inverse magneto-elastic effect: the magnetisation caused by mechanical stretching is almost equal to the magnetisation caused by an external magnetic field