Modeling of the minimized two-phase flow frictional pressure drop in a small tube with different correlations

The major parameters of interest in heat transfer research are the refrigerant charge, pressure drop, and heat transfer capacity. Smaller channels reduce the refrigerant charge with higher heat transfer capability due to the increased in surface area to volume ratio but at the expense of a higher pressure drop. Differences between the predicted and experimental frictional pressure drop of two-phase flow in small tubes have frequently been discussed. Factors that could have contributed to that effect have been attributed to the correlations used to model the flow, some being modified from the originals developed for a macro system. Experimental test-rigs have varied in channel geometry, refrigerant type, and flow conditions. Thousands of data have been collected to find a common point among the differences. This paper reports an investigation of four different two-phase friction factor correlations used in the modeling of the frictional two-phase flow pressure drop of refrigerant R-22. One had been specifically developed for laminar flow in a smooth channel, another was modified from a laminar flow in a smooth pipe to be used for a rough channel, and two correlations are specific for turbulent flow that consider internal pipe surface roughness. Genetic algorithm, an optimization scheme, is used to search for the minimum friction factor and minimum frictional pressure drop under optimized conditions of the mass flux and vapor quality. The results show that a larger pressure drop does come with a smaller channel. A large discrepancy exists between the correlations investigated; between the ones that does not consider surface roughness and that which does, as well as between flow under laminar and turbulent flow conditions

The effect of the rheocast process on the microstructure and mechanical properties of Al-5.7Si-2Cu-0.3Mg alloy

This study shows the results of an experimental investigation of semisolid rheocasting of Al-5.7Si-2Cu-0.3Mg alloy using a cooling slope (CS) casting technique. However, the challenge is to determine process parameters of the CS process to get a desirable microstructure in the semisolid feedstock material. cooling slope technique was employed to create feedstock material for thixoforming under an argon gas atmosphere, where on an inclined plate that was fixed at a 60° slope angle, molten alloy is poured at different temperatures of 640°C, 650°C and 660°C at lengths 300, 400 and 500 mm. Examination the microstructure with optical microscope observed that the microstructure of conventionally cast alloy presented coarse and dendritic primary α-Al phase, whereas rheocast alloy included fine and nondendritic primary α-Al phase with homogeneous distribution of eutectic phase. The best CS processing condition has been identified for optimum pouring temperature of 650°C and the slope length of 400 mm as average globular grain size of around 31.67 ± 3 μm and a shape factor of about 0.66 ± 0.09 were obtained. The mechanical properties of conventional cast alloy were enhanced by the CS casting process. The ultimate tensile strength, the yield strength and elongation of the rheocast alloy were increased by 10%, 12% and 22% respectively compared to the conventional cast alloy. due to a reduction in shrinkage and porosity of the microstructure of the CS alloy

Organic materials as polymer electrolytes for supercapacitor application

Supercapacitors inevitably attract much attention among the scientific community and the general public since they combine the desirable characteristics of batteries and capacitors. The successful development of environmentally friendly supercapacitors is possible thanks to the organic materials obtained from renewable sources that are considered viable alternative materials for a safer and higher energy polymer electrolytes (PE) system. These organic polymer electrolytes (OPEs) are generally materials consisting of carbon and other atoms, such as oxygen, nitrogen, and halogen. This system is supramolecular in nature and produces high ionic conductivity when doped with ions. There is a myriad of future supercapacitor applications, including their use as supplementary energy sources in the electric grid, electric and microhybrid vehicles, and cell phone base stations. This chapter specifically discusses the recent progress made in the application of OPEs, their performance, challenges, and future directions in the context of supercapacitors

Application of response surface methodology for chloride transport properties in nano metaclayed-UHPC

The major concern on the deterioration of reinforced concrete structure is due to the corrosion of steel reinforcement from the aggressive environment such as chloride penetration. Ultra-high performance concrete (UHPC) is an advanced concrete material having ultra-high strength with excellent durability properties. Inclusion of nano metaclay in UHPC is expected to overcome the chloride transport properties in UHPC by providing nano filler effect. Two (2) assessments were conducted which are chloride content and chloride depth were examined. All the concrete specimens were immersed in 3% NaCl solution up to 365 days and the tests conducted were performed at 3, 7, 28, 56, 91, 182 and 365 days. Response surface method (RSM) was performed to evaluate the interaction and relationship between operating variables (compressive strength and nano metaclay content). Based on RSM analysis, inclusion of nano metaclay in UHPC have good relationship towards the chloride resistance characteristics and adequate durability performance in terms of chloride penetration resistance. The results exhibited that inclusion of 1% nano metaclay significantly and positively affect in term of chloride penetration resistance

Synthetic graphite production of oil palm trunk chip at various heating rate via pyrolisis process

Synthetic graphite was synthesized from oil palm trunk chip in controlled heating condition or pyrolysis process. The heating rate (5 °/min, 10 °/min and 20 °/min) were varied whilst the heating temperature at 800 °C was fixed. After heat treatment process, the samples were characterized by X-Ray Diffraction (XRD) and analyzed using X’Pert Highscore Plus software. Graphite phase was analysed by XRD and it was further supported by RAMAN spectroscopy analysis to confirm the graphitic nature of the synthetic graphite obtained. The morphological study was carried out by using Scanning Electron Microscope (SEM). Based on the analysis, it was confirm that synthetic graphite was successfully synthesized by heat treatment at 800 °C (20 °/min heating rate). Synthetic graphite were observed in the form of amorphous carbon based on the XRD diffraction pattern that match with the reference code of 00-041-1487. RAMAN spectroscopy also showed the formation on D, G and 2D peaks at the respective wavenumber of 1250 cm-1, 1625 cm-1 and 2700 cm-1

Spatial distribution and long-term persistence of Wolbachia-infected Aedes aegypti in the Mentari Court, Malaysia

Dengue is endemic in Malaysia, and vector control strategies are vital to reduce dengue transmission. The Wolbachia strain wAlbB carried by both sexes of Ae. aegypti was released in Mentari Court, a high-rise residential site, in October 2017 and stopped after 20 weeks. Wolbachia frequencies are still being monitored at multiple traps across this site, providing an opportunity to examine the spatiotemporal distribution of Wolbachia and mosquito density with respect to year, residential block, and floor, using spatial interpolation in ArcGIS, GLMs, and contingency analyses. In just 12 weeks, Wolbachia-infected mosquitoes were established right across the Mentari Court site with an overall infection frequency of >90%. To date, the Wolbachia frequency of Ae. aegypti has remained high in all areas across the site despite releases finishing four years ago. Nevertheless, the Wolbachia invaded more rapidly in some residential blocks than others, and also showed a relatively higher frequency on the eighth floor. The Ae. aegypti index tended to differ somewhat between residential blocks, whilst the Ae. albopictus index was relatively higher at the top and bottom floors of buildings. In Mentari Court, only a short release period was required to infiltrate Wolbachia completely and stably into the natural population. The results inform future releases in comparable sites in a dengue control programme

Soy protein–gum karaya conjugate: emulsifying activity and rheological behavior in aqueous system and oil in water emulsion

The main objective of this study is to investigate the effects of mixing and conjugation of soy protein isolate (SPI) with gum karaya on the characteristics of the hybrid polymer (protein–gum) in both aqueous systems and oil-in-water (O/W) emulsions. It was hypothesized that the covalent linkage of gum karaya with SPI would improve the emulsifying activity and rheological properties of both polymers. Conjugation occurred under controlled conditions (i.e., 60 °C and 75 % relative humidity, 3 days). The conjugated hybrid polymer produced smaller droplet with better uniformity, higher viscosity and stronger emulsifying activity than native gum karaya, suggesting the conjugated polymer provided a bulkier secondary layer with more efficient coverage around oil droplets, thereby inducing stronger resistance against droplet aggregation and flocculation. Emulsions containing the native gum karaya produced the largest droplet size among all prepared emulsions (D 3,2 = 8.6 μm; D 4,3 = 22.4 μm); while the emulsion containing protein–gum conjugate (1:1 g/g) had the smallest droplet size (D 3,2 = 0.2 μm; D 4,3 = 0.7 μm) with lower polydispersity. The protein–gum conjugate (1:1 g/g) also showed the highest elastic and viscous modulus, the lowest polydispersity (span) and the highest emulsifying activity among all native, mixed and conjugated polymers. Therefore, the percentage of gum karaya used for production of O/W emulsion can be decreased by partially replacing it with the conjugated gum

Elective Cancer Surgery in COVID-19-Free Surgical Pathways During the SARS-CoV-2 Pandemic: An International, Multicenter, Comparative Cohort Study.

PURPOSE: As cancer surgery restarts after the first COVID-19 wave, health care providers urgently require data to determine where elective surgery is best performed. This study aimed to determine whether COVID-19-free surgical pathways were associated with lower postoperative pulmonary complication rates compared with hospitals with no defined pathway. PATIENTS AND METHODS: This international, multicenter cohort study included patients who underwent elective surgery for 10 solid cancer types without preoperative suspicion of SARS-CoV-2. Participating hospitals included patients from local emergence of SARS-CoV-2 until April 19, 2020. At the time of surgery, hospitals were defined as having a COVID-19-free surgical pathway (complete segregation of the operating theater, critical care, and inpatient ward areas) or no defined pathway (incomplete or no segregation, areas shared with patients with COVID-19). The primary outcome was 30-day postoperative pulmonary complications (pneumonia, acute respiratory distress syndrome, unexpected ventilation). RESULTS: Of 9,171 patients from 447 hospitals in 55 countries, 2,481 were operated on in COVID-19-free surgical pathways. Patients who underwent surgery within COVID-19-free surgical pathways were younger with fewer comorbidities than those in hospitals with no defined pathway but with similar proportions of major surgery. After adjustment, pulmonary complication rates were lower with COVID-19-free surgical pathways (2.2% v 4.9%; adjusted odds ratio [aOR], 0.62; 95% CI, 0.44 to 0.86). This was consistent in sensitivity analyses for low-risk patients (American Society of Anesthesiologists grade 1/2), propensity score-matched models, and patients with negative SARS-CoV-2 preoperative tests. The postoperative SARS-CoV-2 infection rate was also lower in COVID-19-free surgical pathways (2.1% v 3.6%; aOR, 0.53; 95% CI, 0.36 to 0.76). CONCLUSION: Within available resources, dedicated COVID-19-free surgical pathways should be established to provide safe elective cancer surgery during current and before future SARS-CoV-2 outbreaks