Very low mass microcables for the ALICE silicon strip detector

Proposal of abstract for LEB99, Snowmass, Colorado, 20-24 September 1999The ALICE Inner Tracker (ITS) silicon strip layers will use kapton/aluminium microcables (12/14 um thickness) exclusively for all interconnections to and from the front-end chips and hybrids, completely eliminating traditional wirebonding. Benefits are increased robustness and an extra degree of dimensional freedom. Utilising a low-power, low temperature and low-force (10-15 grams) single-point TAB bonding process, aluminium traces are directly bonded through bonding windows in the kapton foil to bond pads on the chips and the hybrid. The same technique is also used to interconnect these microcables to create multi-layer bus structures with "bonded via's". A double-sided strip detector using prototype cables has been installed in the NA57 experiment in 1998

First mock-up of the CBM STS module based on a new assembly concept

A molecular dynamics model has been developed to investigate the effect of the crystallographic orientation on the material deformation behaviors in nano- indentation/scratching of BCC iron. Two cases with different substrate orientations have been simulated. The orientations along x, y and z direction are [001], [100] and [010] for Case I and [111], [-1-12] and [1-10] for Case II, respectively. Case I and Case II exhibit different deformation patterns in the substrate. During indentation, the pile-up can be observed in Case I, but not in Case II. During scratching the pile-up ahead of the movement of the indenter has been enlarged in Case I, while a chip with the disordered atoms is generated in Case II. It has been found that Case I has both higher hardness and larger coefficient of friction. The ratios of the hardness and the coefficient of friction between cases I and II are nearly 2. The reason is attributed to the different crystallographic orientations used in both cases

Performance of the Electromagnetic Pixel Calorimeter Prototype EPICAL-2

The first evaluation of an ultra-high granularity digital electromagnetic calorimeter prototype using 1.0-5.8 GeV/c electrons is presented. The $25\times10^6$ pixel detector consists of 24 layers of ALPIDE CMOS MAPS sensors, with a pitch of around 30~$\mu$m, and has a depth of almost 20 radiation lengths of tungsten absorber. Ultra-thin cables allow for a very compact design. The properties that are critical for physics studies are measured: electromagnetic shower response, energy resolution and linearity. The stochastic energy resolution is comparable with the state-of-the art resolution for a Si-W calorimeter, with data described well by a simulation model using GEANT and Allpix$^2$. The performance achieved makes this technology a good candidate for use in the ALICE FoCal upgrade, and in general demonstrates the strong potential for future applications in high-energy physics.Comment: 30 pages, 19 figures, submitted to JINS

STRASSE: A Silicon Tracker for Quasi-free Scattering Measurements at the RIBF

STRASSE (Silicon Tracker for RAdioactive nuclei Studies at SAMURAI Experiments) is a new detection system under construction for quasi-free scattering (QFS) measurements at 200-250 MeV/nucleon at the RIBF facility of the RIKEN Nishina Center. It consists of a charged-particle silicon tracker coupled with a dedicated thick liquid hydrogen target (up to 150-mm long) in a compact geometry to fit inside large scintillator or germanium arrays. Its design was optimized for two types of studies using QFS: missing-mass measurements and in-flight prompt $\gamma$-ray spectroscopy. This article describes (i) the resolution requirements needed to go beyond the sensitivity of existing systems for these two types of measurements, (ii) the conceptual design of the system using detailed simulations of the setup and (iii) its complete technical implementation and challenges. The final tracker aims at a sub-mm reaction vertex resolution and is expected to reach a missing-mass resolution below 2 MeV in $\sigma$ for $(p,2p)$ reactions when combined with the CsI(Na) CATANA array.Comment: 25 pages, 29 figure

Performance of the electromagnetic and hadronic prototype segments of the ALICE Forward Calorimeter

We present the performance of a full-length prototype of the ALICE Forward Calorimeter (FoCal). The detector is composed of a silicon-tungsten electromagnetic sampling calorimeter with longitudinal and transverse segmentation (FoCal-E) of about 20$X_0$ and a hadronic copper-scintillating-fiber calorimeter (FoCal-H) of about 5$\lambda_{\rm int}$. The data were taken between 2021 and 2023 at the CERN PS and SPS beam lines with hadron (electron) beams up to energies of 350 (300) GeV. Regarding FoCal-E, we report a comprehensive analysis of its response to minimum ionizing particles across all pad layers. The longitudinal shower profile of electromagnetic showers is measured with a layer-wise segmentation of 1$X_0$. As a projection to the performance of the final detector in electromagnetic showers, we demonstrate linearity in the full energy range, and show that the energy resolution fulfills the requirements for the physics needs. Additionally, the performance to separate two-showers events was studied by quantifying the transverse shower width. Regarding FoCal-H, we report a detailed analysis of the response to hadron beams between 60 and 350 GeV. The results are compared to simulations obtained with a Geant4 model of the test beam setup, which in particular for FoCal-E are in good agreement with the data. The energy resolution of FoCal-E was found to be lower than 3% at energies larger than 100 GeV. The response of FoCal-H to hadron beams was found to be linear, albeit with a significant intercept that is about factor 2 larger than in simulations. Its resolution, which is non-Gaussian and generally larger than in simulations, was quantified using the FWHM, and decreases from about 16% at 100 GeV to about 11% at 350 GeV. The discrepancy to simulations, which is particularly evident at low hadron energies, needs to be further investigated.Comment: 55 pages (without acronyms), 45 captioned figure

Performance of the electromagnetic pixel calorimeter prototype Epical-2

The first evaluation of an ultra-high granularity digital electromagnetic calorimeter prototype using 1.0-5.8 GeV/c electrons is presented. The 25 × 106 pixel detector consists of 24 layers of ALPIDE CMOS MAPS sensors, with a pitch of around 30 μm, and has a depth of almost 20 radiation lengths of tungsten absorber. Ultra-thin cables allow for a very compact design. The properties that are critical for physics studies are measured: electromagnetic shower response, energy resolution and linearity. The stochastic energy resolution is comparable with the state-of-the art resolution for a Si-W calorimeter, with data described well by a simulation model using Geant4 and Allpix2. The performance achieved makes this technology a good candidate for use in the ALICE FoCal upgrade, and in general demonstrates the strong potential for future applications in high-energy physics

Alignment of the ALICE Inner Tracking System with cosmic-ray tracks

37 pages, 15 figures, revised version, accepted by JINSTALICE (A Large Ion Collider Experiment) is the LHC (Large Hadron Collider) experiment devoted to investigating the strongly interacting matter created in nucleus-nucleus collisions at the LHC energies. The ALICE ITS, Inner Tracking System, consists of six cylindrical layers of silicon detectors with three different technologies; in the outward direction: two layers of pixel detectors, two layers each of drift, and strip detectors. The number of parameters to be determined in the spatial alignment of the 2198 sensor modules of the ITS is about 13,000. The target alignment precision is well below 10 micron in some cases (pixels). The sources of alignment information include survey measurements, and the reconstructed tracks from cosmic rays and from proton-proton collisions. The main track-based alignment method uses the Millepede global approach. An iterative local method was developed and used as well. We present the results obtained for the ITS alignment using about 10^5 charged tracks from cosmic rays that have been collected during summer 2008, with the ALICE solenoidal magnet switched off.Peer reviewe

The Bergen proton CT system

The Bergen proton Computed Tomography (pCT) is a prototype detector under construction. It aims to have the capability to track and measure ions’ energy deposition to minimize uncertainty in proton treatment planning. It is a high granularity digital tracking calorimeter, where the first two layers will act as tracking layers to obtain positional information of the incoming particle. The remainder of the detector will act as a calorimeter. Beam tests have been performed with multiple beams. These tests have shown that the ALPIDE chip sensor can measure the deposited energy, making it possible for the sensors to distinguish between the tracks in the Digital Tracking Calorimeter (DTC)