Nanoprecipitation versus emulsion-based techniques for the encapsulation of proteins into biodegradable nanoparticles and process-related stability issues

The goal of this study was to investigate the entrapment of 3 different model proteins (tetanus toxoid, lysozyme, and insulin) into poly(D,L-lactic acid) and poly(D,L-lactic-co-glycolic acid) nanoparticles and to address process-related stability issues. For that purpose, a modified nanoprecipitation method as well as 2 emulsion-based encapsulation techniques (ie, a solid-in oil-in water (s/o/w) and a double emulsion (w1/o/w2) method) were used. The main modification of nanoprecipitation involved the use of a wide range of miscible organic solvents such as dimethylsulfoxide and ethanol instead of the common acetone and water. The results obtained showed that tetanus toxoid and lysozyme were efficiently incorporated by the double emulsion procedure when ethyl acetate was used as solvent (>80% entrapment efficiency), whereas it was necessary to use methylene chloride to achieve high insulin entrapment efficiencies. The use of the s/o/w method or the formation of a more hydrophobic protein-surfactant ion pair did not improve protein loading. The nanoprecipitation method led to a homogenous population of small nanoparticles (with size ranging from ≈130 to 560 nm) and in some cases also improved experimental drug loadings, especially for lysozyme (entrapment efficiency >90%). With respect to drug content determination, a simple and quick matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF MS) method provided results very close to those obtained by reverse phase-high-performance liquid chromatography. With respect to protein stability, the duration and intensity of sonication were not a concern for tetanus toxoid, which retained more than 95% of its antigenicity after treatment for 1 minute. Only a high methylene chloride:water ratio was shown to slightly decrease toxoid antigenicity. Finally, no more than 3.3% of A21 desamido insulin and only traces of covalent insulin dimer were detected in nanoparticles. In conclusion, both the double emulsion and nanoprecipitation methods allowed efficient protein encapsulation. MALDI-TOF MS allowed accurate drug content determination. The manufacturing processes evaluated did not damage the primary structure of insuli

Poly(lactic-co-glycolic) acid drug delivery systems through transdermal pathway : an overview

In past few decades, scientists have made tremendous advancement in the field of drug delivery systems (DDS), through transdermal pathway, as the skin represents a ready and large surface area for delivering drugs. Efforts are in progress to design efficient transdermal DDS that support sustained drug release at the targeted area for longer duration in the recommended therapeutic window without producing side-effects. Poly(lactic-co-glycolic acid) (PLGA) is one of the most promising Food and Drug Administration approved synthetic polymers in designing versatile drug delivery carriers for different drug administration routes, including transdermal drug delivery. The present review provides a brief introduction over the transdermal drug delivery and PLGA as a material in context to its role in designing drug delivery vehicles. Attempts are made to compile literatures over PLGA-based drug delivery vehicles, including microneedles, nanoparticles, and nanofibers and their role in transdermal drug delivery of different therapeutic agents. Different nanostructure evaluation techniques with their working principles are briefly explained.RL thanks the funding support from Singapore National Research Foundation under its Translational and Clinical Research Flagship Programme (NMRC/TCR/008-SERI/2013) and administered by the Singapore Ministry of Health’s National Medical Research Council and Co-operative Basic Research Grant from the Singapore National Medical Research Council (Project No. NMRC/CBRG/0048/2013).info:eu-repo/semantics/publishedVersio

Preparation and Characterization of Cationic PLA-PEG Nanoparticles for Delivery of Plasmid DNA

The purpose of the present work was to formulate and evaluate cationic poly(lactic acid)-poly(ethylene glycol) (PLA-PEG) nanoparticles as novel non-viral gene delivery nano-device. Cationic PLA-PEG nanoparticles were prepared by nanoprecipitation method. The gene loaded nanoparticles were obtained by incubating the report gene pEGFP with cationic PLA-PEG nanoparticles. The physicochemical properties (e.g., morphology, particle size, surface charge, DNA binding efficiency) and biological properties (e.g., integrity of the released DNA, protection from nuclease degradation, plasma stability, in vitro cytotoxicity, and in vitro transfection ability in Hela cells) of the gene loaded PLA-PEG nanoparticles were evaluated, respectively. The obtained cationic PLA-PEG nanoparticles and gene loaded nanoparticles were both spherical in shape with average particle size of 89.7 and 128.9 nm, polydispersity index of 0.185 and 0.161, zeta potentials of +28.9 and +16.8 mV, respectively. The obtained cationic PLA-PEG nanoparticles with high binding efficiency (>95%) could protect the loaded DNA from the degradation by nuclease and plasma. The nanoparticles displayed sustained-release properties in vitro and the released DNA maintained its structural and functional integrity. It also showed lower cytotoxicity than Lipofectamine 2000 and could successfully transfect gene into Hela cells even in presence of serum. It could be concluded that the established gene loaded cationic PLA-PEG nanoparticles with excellent properties were promising non-viral nano-device, which had potential to make cancer gene therapy achievable

Pulmonary Delivery of Proteins Using Nanocomposite Microcarriers.

In this study, Taguchi design was used to determine optimal parameters for the preparation of bovine serum albumin (BSA)-loaded nanoparticles (NPs) using a biodegradable polymer poly(glycerol adipate-co-ω-pentadecalactone) (PGA-co-PDL). NPs were prepared, using BSA as a model protein, by the double emulsion evaporation process followed by spray-drying from leucine to form nanocomposite microparticles (NCMPs). The effect of various parameters on NP size and BSA loading were investigated and dendritic cell (DC) uptake and toxicity. NCMPs were examined for their morphology, yield, aerosolisation, in vitro release behaviour and BSA structure. NP size was mainly affected by the polymer mass used and a small particle size ≤500 nm was achieved. High BSA (43.67 ± 2.3 μg/mg) loading was influenced by BSA concentration. The spray-drying process produced NCMPs (50% yield) with a porous corrugated surface, aerodynamic diameter 1.46 ± 141 μm, fine particle dose 45.0 ± 4.7 μg and fine particle fraction 78.57 ± 0.1%, and a cumulative BSA release of 38.77 ± 3.0% after 48 h. The primary and secondary structures were maintained as shown by sodium dodecyl sulphate poly (acrylamide) gel electrophoresis and circular dichroism. Effective uptake of NPs was seen in DCs with >85% cell viability at 5 mg/mL concentration after 4 h. These results indicate the optimal process parameters for the preparation of protein-loaded PGA-co-PDL NCMPs suitable for inhalation. © 2015 Wiley Periodicals, Inc. and the American Pharmacists Association J Pharm Sci

Co-encapsulation of human serum albumin and superparamagnetic iron oxide in PLGA nanoparticles: Part I. Effect of process variables on the mean size

PLGA (poly d,l-lactic-co-glycolic acid) nanoparticles (NPs) encapsulating magnetite nanoparticles (MNPs) along with a model drug human serum albumin (HSA) were prepared by double emulsion solvent evaporation method. This Part I will focus on size and size distribution of prepared NPs, whereas encapsulation efficiency will be discussed in Part II. It was found that mean hydrodynamic particle size was influenced by five important process variables. To explore their effects, a five-factorial, three-level experimental design and statistical analysis were carried out using STATISTICA® software. Effect of process variables on the mean size of nanoparticles was investigated and finally conditions to minimize size of NPs were proposed. GAMS™/MINOS software was used for optimization. The mean hydrodynamic size of nanoparticles ranged from 115 to 329 nm depending on the process conditions. Smallest possible mean particle size can be achieved by using low polymer concentration and high dispersion energy (enough sonication time) along with small aqueous/organic volume ratio

Designing Bioactive Delivery Systems for Tissue Regeneration

The direct infusion of macromolecules into defect sites generally does not impart adequate physiological responses. Without the protection of delivery systems, inductive molecules may likely redistribute away from their desired locale and are vulnerable to degradation. In order to achieve efficacy, large doses supplied at interval time periods are necessary, often at great expense and ensuing detrimental side effects. The selection of a delivery system plays an important role in the rate of re-growth and functionality of regenerating tissue: not only do the release kinetics of inductive molecules and their consequent bioactivities need to be considered, but also how the delivery system interacts and integrates with its surrounding host environment. In the current review, we describe the means of release of macromolecules from hydrogels, polymeric microspheres, and porous scaffolds along with the selection and utilization of bioactive delivery systems in a variety of tissue-engineering strategies

Preparation of biodegradable polymeric nanoparticles for pharmaceutical applications using glass capillary microfluidics

This paper was accepted for publication in the journal Chemical Engineering Science and the definitive published version is available at http://dx.doi.org/10.1016/j.ces.2015.06.025The aim of this study was to develop a new microfluidic approach for the preparation of nanoparticles with tuneable sizes based on micromixing/direct nanoprecipitation in a coaxial assembly of tapered-end glass capillaries. The organic phase was 1 wt% poly(ε-caprolactone) (PCL) or poly(dl-lactic acid) (PLA) in tetrahydrofuran and the antisolvent was Milli-Q water. The size of nanoparticles was precisely controlled over a range of 190–650 nm by controlling phase flow rates, orifice size and flow configuration (two-phase co-flow or counter-current flow focusing). Smaller particles were produced in a flow focusing device, because the organic phase stream was significantly narrower than the orifice and remained narrow for a longer distance downstream of the orifice. The mean size of PCL particles produced in a flow focusing device with an orifice size of 200 μm, an organic phase flow rate of 1.7 mL h−1 and an aqueous-to-organic flow rate ratio of 10 was below 200 nm. The size of nanoparticles decreased with decreasing the orifice size and increasing the aqueous-to-organic phase flow rate ratio. Due to higher affinity for water and amorphous structure, PLA nanoparticles were smaller and exhibited a smoother surface and more rounded shape than PCL particles

Development of Novel Octanoyl Chitosan Nanoparticles for Improved Rifampicin Pulmonary Delivery: Optimization by Factorial Design

A novel hydrophobic chitosan derivative, octanoyl chitosan (OC) with improved organic solubility was synthesized, characterized, and employed for the preparation of rifampicin (Rif) encapsulated nanoparticle formulations for pulmonary delivery. OC was characterized to confirm acyl group substitution and cytotoxicity in A549 epithelial lung cells. OC nanoparticles were produced by the double emulsion solvent evaporation technique without cross-linking and characterized for particle size distribution, morphology, crystallinity, thermal stability, aerosol delivery, and drug release rate. OC was successfully synthesized with substitution degree of 44.05 ± 1.75%, and solubility in a range of organic solvents. Preliminary cytotoxicity studies of OC showed no effect on cell viability over a period of 24 h on A549 cell lines. OC nanoparticles were optimized using a 32full factorial design. An optimized batch of OC nanoparticles, smooth and spherical in morphology, had mean hydrodynamic diameter of 253 ± 19.06 nm (PDI 0.323 ± 0.059) and entrapment efficiency of 64.86 ± 7.73% for rifampicin. Pulmonary deposition studies in a two-stage impinger following aerosolization of nanoparticles from a jet nebulizer gave a fine particle fraction of 43.27 ± 4.24%. In vitro release studies indicated sustained release (73.14 ± 3.17%) of rifampicin from OC nanoparticles over 72 h, with particles demonstrating physical stability over 2 months. In summary, the results confirmed the suitability of the developed systems for pulmonary delivery of drugs with excellent aerosolization properties and sustained-release characteristics. © 2018, American Association of Pharmaceutical Scientists