A high speed serializer/deserializer design

A Serializer/Deserializer (SerDes) is a circuit that converts parallel data into a serial stream and vice versa. It helps solve clock/data skew problems, simplifies data transmission, lowers the power consumption and reduces the chip cost. The goal of this project was to solve the challenges in high speed SerDes design, which included the low jitter design, wide bandwidth design and low power design. A quarter-rate multiplexer/demultiplexer (MUX/DEMUX) was implemented. This quarter-rate structure decreases the required clock frequency from one half to one quarter of the data rate. It is shown that this significantly relaxes the design of the VCO at high speed and achieves lower power consumption. A novel multi-phase LC-ring oscillator was developed to supply a low noise clock to the SerDes. This proposed VCO combined an LC-tank with a ring structure to achieve both wide tuning range (11%) and low phase noise (-110dBc/Hz at 1MHz offset). With this structure, a data rate of 36 Gb/s was realized with a measured peak-to-peak jitter of 10ps using 0.18microm SiGe BiCMOS technology. The power consumption is 3.6W with 3.4V power supply voltage. At a 60 Gb/s data rate the simulated peak-to-peak jitter was 4.8ps using 65nm CMOS technology. The power consumption is 92mW with 2V power supply voltage. A time-to-digital (TDC) calibration circuit was designed to compensate for the phase mismatches among the multiple phases of the PLL clock using a three dimensional fully depleted silicon on insulator (3D FDSOI) CMOS process. The 3D process separated the analog PLL portion from the digital calibration portion into different tiers. This eliminated the noise coupling through the common substrate in the 2D process. Mismatches caused by the vertical tier-to-tier interconnections and the temperature influence in the 3D process were attenuated by the proposed calibration circuit. The design strategy and circuits developed from this dissertation provide significant benefit to both wired and wireless applications

Experimental Evaluation and Comparison of Time-Multiplexed Multi-FPGA Routing Architectures

Emulating large complex designs require multi-FPGA systems (MFS). However, inter-FPGA communication is confronted by the challenge of lack of interconnect capacity due to limited number of FPGA input/output (I/O) pins. Serializing parallel signals onto a single trace effectively addresses the limited I/O pin obstacle. Besides the multiplexing scheme and multiplexing ratio (number of inter-FPGA signals per trace), the choice of the MFS routing architecture also affect the critical path latency. The routing architecture of an MFS is the interconnection pattern of FPGAs, fixed wires and/or programmable interconnect chips. Performance of existing MFS routing architectures is also limited by off-chip interface selection. In this dissertation we proposed novel 2D and 3D latency-optimized time-multiplexed MFS routing architectures. We used rigorous experimental approach and real sequential benchmark circuits to evaluate and compare the proposed and existing MFS routing architectures. This research provides a new insight into the encouraging effects of using off-chip optical interface and three dimensional MFS routing architectures. The vertical stacking results in shorter off-chip links improving the overall system frequency with the additional advantage of smaller footprint area. The proposed 3D architectures employed serialized interconnect between intra-plane and inter-plane FPGAs to address the pin limitation problem. Additionally, all off-chip links are replaced by optical fibers that exhibited latency improvement and resulted in faster MFS. Results indicated that exploiting third dimension provided latency and area improvements as compared to 2D MFS. We also proposed latency-optimized planar 2D MFS architectures in which electrical interconnections are replaced by optical interface in same spatial distribution. Performance evaluation and comparison showed that the proposed architectures have reduced critical path delay and system frequency improvement as compared to conventional MFS. We also experimentally evaluated and compared the system performance of three inter-FPGA communication schemes i.e. Logic Multiplexing, SERDES and MGT in conjunction with two routing architectures i.e. Completely Connected Graph (CCG) and TORUS. Experimental results showed that SERDES attained maximum frequency than the other two schemes. However, for very high multiplexing ratios, the performance of SERDES & MGT became comparable

Energy-Efficient Receiver Design for High-Speed Interconnects

High-speed interconnects are of vital importance to the operation of high-performance computing and communication systems, determining the ultimate bandwidth or data rates at which the information can be exchanged. Optical interconnects and the employment of high-order modulation formats are considered as the solutions to fulfilling the envisioned speed and power efficiency of future interconnects. One common key factor in bringing the success is the availability of energy-efficient receivers with superior sensitivity. To enhance the receiver sensitivity, improvement in the signal-to-noise ratio (SNR) of the front-end circuits, or equalization that mitigates the detrimental inter-symbol interference (ISI) is required. In this dissertation, architectural and circuit-level energy-efficient techniques serving these goals are presented. First, an avalanche photodetector (APD)-based optical receiver is described, which utilizes non-return-to-zero (NRZ) modulation and is applicable to burst-mode operation. For the purposes of improving the overall optical link energy efficiency as well as the link bandwidth, this optical receiver is designed to achieve high sensitivity and high reconfiguration speed. The high sensitivity is enabled by optimizing the SNR at the front-end through adjusting the APD responsivity via its reverse bias voltage, along with the incorporation of 2-tap feedforward equalization (FFE) and 2-tap decision feedback equalization (DFE) implemented in current-integrating fashion. The high reconfiguration speed is empowered by the proposed integrating dc and amplitude comparators, which eliminate the RC settling time constraints. The receiver circuits, excluding the APD die, are fabricated in 28-nm CMOS technology. The optical receiver achieves bit-error-rate (BER) better than 1E−12 at −16-dBm optical modulation amplitude (OMA), 2.24-ns reconfiguration time with 5-dB dynamic range, and 1.37-pJ/b energy efficiency at 25 Gb/s. Second, a 4-level pulse amplitude modulation (PAM4) wireline receiver is described, which incorporates continuous time linear equalizers (CTLEs) and a 2-tap direct DFE dedicated to the compensation for the first and second post-cursor ISI. The direct DFE in a PAM4 receiver (PAM4-DFE) is made possible by the proposed CMOS track-and-regenerate slicer. This proposed slicer offers rail-to-rail digital feedback signals with significantly improved clock-to-Q delay performance. The reduced slicer delay relaxes the settling time constraint of the summer circuits and allows the stringent DFE timing constraint to be satisfied. With the availability of a direct DFE employing the proposed slicer, inductor-based bandwidth enhancement and loop-unrolling techniques, which can be power/area intensive, are not required. Fabricated in 28-nm CMOS technology, the PAM4 receiver achieves BER better than 1E−12 and 1.1-pJ/b energy efficiency at 60 Gb/s, measured over a channel with 8.2-dB loss at Nyquist frequency. Third, digital neural-network-enhanced FFEs (NN-FFEs) for PAM4 analog-to-digital converter (ADC)-based optical interconnects are described. The proposed NN-FFEs employ a custom learnable piecewise linear (PWL) activation function to tackle the nonlinearities with short memory lengths. In contrast to the conventional Volterra equalizers where multipliers are utilized to generate the nonlinear terms, the proposed NN-FFEs leverage the custom PWL activation function for nonlinear operations and reduce the required number of multipliers, thereby improving the area and power efficiencies. Applications in the optical interconnects based on micro-ring modulators (MRMs) are demonstrated with simulation results of 50-Gb/s and 100-Gb/s links adopting PAM4 signaling. The proposed NN-FFEs and the conventional Volterra equalizers are synthesized with the standard-cell libraries in a commercial 28-nm CMOS technology, and their power consumptions and performance are compared. Better than 37% lower power overhead can be achieved by employing the proposed NN-FFEs, in comparison with the Volterra equalizer that leads to similar improvement in the symbol-error-rate (SER) performance.</p

WDM/TDM PON bidirectional networks single-fiber/wavelength RSOA-based ONUs layer 1/2 optimization

This Thesis proposes the design and the optimization of a hybrid WDM/TDM PON at the L1 (PHY) and L2 (MAC) layers, in terms of minimum deployment cost and enhanced performance for Greenfield NGPON. The particular case of RSOA-based ONUs and ODN using a single-fibre/single-wavelength is deeply analysed. In this WDM/TDM PON relevant parameters are optimized. Special attention has been given at the main noise impairment in this type of networks: the Rayleigh Backscattering effect, which cannot be prevented. To understand its behaviour and mitigate its effects, a novel mathematical model for the Rayleigh Backscattering in burst mode transmission is presented for the first time, and it has been used to optimize the WDM/TDM RSOA based PON. Also, a cost-effective, simple design SCM WDM/TDM PON with rSOA-based ONU, was optimized and implemented. This prototype was successfully tested showing high performance, robustness, versatility and reliability. So, the system is able to give coverage up to 1280 users at 2.5 Gb/s / 1.25 Gb/s downstream/upstream, over 20 Km, and being compatible with the GPON ITU-T recommendation. This precedent has enabled the SARDANA network to extend the design, architecture and capabilities of a WDM/TDM PON for a long reach metro-access network (100 km). A proposal for an agile Transmission Convergence sub-layer is presented as another relevant contribution of this work. It is based on the optimization of the standards GPON and XG-PON (for compatibility), but applied to a long reach metro-access TDM/WDM PON rSOA-based network with higher client count. Finally, a proposal of physical implementation for the SARDANA layer 2 and possible configurations for SARDANA internetworking, with the metro network and core transport network, are presented

High Performance Optical Transmitter Ffr Next Generation Supercomputing and Data Communication

High speed optical interconnects consuming low power at affordable prices are always a major area of research focus. For the backbone network infrastructure, the need for more bandwidth driven by streaming video and other data intensive applications such as cloud computing has been steadily pushing the link speed to the 40Gb/s and 100Gb/s domain. However, high power consumption, low link density and high cost seriously prevent traditional optical transceiver from being the next generation of optical link technology. For short reach communications, such as interconnects in supercomputers, the issues related to the existing electrical links become a major bottleneck for the next generation of High Performance Computing (HPC). Both applications are seeking for an innovative solution of optical links to tackle those current issues. In order to target the next generation of supercomputers and data communication, we propose to develop a high performance optical transmitter by utilizing CISCO Systems®\u27s proprietary CMOS photonic technology. The research seeks to achieve the following outcomes: 1. Reduction of power consumption due to optical interconnects to less than 5pJ/bit without the need for Ring Resonators or DWDM and less than 300fJ/bit for short distance data bus applications. 2. Enable the increase in performance (computing speed) from Peta-Flop to Exa-Flops without the proportional increase in cost or power consumption that would be prohibitive to next generation system architectures by means of increasing the maximum data transmission rate over a single fiber. 3. Explore advanced modulation schemes such as PAM-16 (Pulse-Amplitude-Modulation with 16 levels) to increase the spectrum efficiency while keeping the same or less power figure. This research will focus on the improvement of both the electrical IC and optical IC for the optical transmitter. An accurate circuit model of the optical device is created to speed up the performance optimization and enable co-simulation of electrical driver. Circuit architectures are chosen to minimize the power consumption without sacrificing the speed and noise immunity. As a result, a silicon photonic based optical transmitter employing 1V supply, featuring 20Gb/s data rate is fabricated. The system consists of an electrical driver in 40nm CMOS and an optical MZI modulator with an RF length of less than 0.5mm in 0.13&mu m SOI CMOS. Two modulation schemes are successfully demonstrated: On-Off Keying (OOK) and Pulse-Amplitude-Modulation-N (PAM-N N=4, 16). Both versions demonstrate signal integrity, interface density, and scalability that fit into the next generation data communication and exa-scale computing. Modulation power at 20Gb/s data rate for OOK and PAM-16 of 4pJ/bit and 0.25pJ/bit are achieved for the first time of an MZI type optical modulator, respectively

Architectural & circuit level techniques to improve energy efficiency of high speed serial links

High performance computing and communication are two key aspects of all information processing systems. With aggressive scaling of silicon technology enabling integration of a large number of transistors in a small area, managing power and thermal reliability has become very challenging. While lowering the power needed for performing computation has been the prime focus for decades, energy consumed for data transfer has recently become a major bottleneck especially in high performance applications. The focus of this thesis is on improving energy efficiency of communication links by exploring design techniques at both the architectural and circuit levels. In the first part of this work, we propose a time-based equalization scheme to implement transmit de-emphasis in voltage-mode output drivers. Using two-level pulse-width modulation, it overcomes the tradeoff between impedance matching, output swing, and de-emphasis resolution in conventional voltage-mode drivers. A prototype PWM-based 5$\,$Gb/s voltage-mode transmitter was implemented in a 90$\,$nm CMOS process and characterized across different channels and output swings to demonstrate the effectiveness of proposed techniques. The horizontal/vertical eye openings (BER=$\rm 10^{-12}$) at the ends of 60$\,$inch and 96$\,$inch stripline channels are 78$\,$mV/0.6$\,$UI and 8$\,$mV/0.3$\,$UI, respectively. This transmitter achieves an energy efficiency of 3.1$\,$mW/Gb/s while compensating for 16-28$\,$dB channel loss, which compares favorably with the state-of-the-art. In the second part, techniques to improve energy efficiency of a complete transceiver are presented. The transmitter employs a novel partially segmented voltage-mode output driver to lower power consumption in pre-drivers during 2-tap FIR equalization. The receiver implements a low power half-rate clock and data recovery with the proposed ring PLL based multi-phase sampling clock generation in CDR loop and charge-based sampling and deserialization. These techniques are verified using the measured results obtained from a 14Gb/s transceiver prototype. Transmitter achieves an energy efficiency of 0.89$\,$mW/Gb/s while securing a 0.36$\,$UI sampling time margin with $\rm{BER=10^{-12}}$ at the end of the channel with 11$\,$dB loss at Nyquist frequency. The receiver recovers sampling clock with 1.8$\,$$\rm{ps_{rms}}$ long term absolute jitter while recovering 14$\,$Gb/s data at $\rm{BER=10^{-12}}$. The receiver achieves an energy efficiency of 1.69$\,$mW/Gb/s. Transmitter and receiver share an LC PLL, which achieves 0.605$\,$$\rm{ps_{rms}}$ integrated jitter at 7$\,$GHz output with an energy efficiency of 0.5$\,$mW/GHz. The transceiver as a whole achieves an energy efficiency of 2.8$\,$mW/Gb/s

Circuit architectures for high speed CMOS clock and data recovery circuits

As semiconductor process technologies continue to scale and the demand for ubiquitous computing devices continues to grow with paradigms such as the internet of things (IOT), the availability of low-cost, low-power, high-speed and robust communication interfaces between these devices will be a major challenge that needs to be addressed. Even in traditional desktop computing devices, the off-chip bandwidth does not scale as fast as the on-chip bandwidth and has therefore been an important bottleneck to the growth in processing speed. Thus, intelligent techniques will have to be developed that allow the traditional lossy channels to be deployed at higher data rates, while minimizing cost and power, without paying much of a performance penalty. Over the last decade and a half, a great amount of research has been done to design monolithic transmitter and receiver integrated circuits (ICs) in silicon complementary metal-oxide semiconductor (CMOS) technology as opposed to traditional discrete SiGe, InP technologies owing to the low cost and ease of integration of CMOS technology. A key component of the receiver is the clock and data recovery (CDR) circuit, which extracts the clock from the incoming data stream and samples the data. The performance of the CDR is a major impediment to increasing data rates in a serial communication system. Several CDR architectures have been proposed to ensure that the performance is comparable to traditional discrete SiGe, InP devices. In this thesis, three different CDR circuit architectures are designed in a 180 nm CMOS process with a target data rate of 2 Gbps and compared in terms of performance, power and area. In order to provide a fair comparison, the corresponding channel and transmitter blocks are also designed and the entire serial communication link is simulated. The fundamentals of CDR circuit design are introduced and a complete guide to analysis and design of CDR circuits for high speed serial links is presented. The results of the comparison help to evaluate power, performance and area trade-offs during the design phase and to choose the right architecture for a given application

Analysis and design on low-power multi-Gb/s serial links

High speed serial links are critical components for addressing the growing demand for I/O bandwidth in next-generation computing applications, such as many-core systems, backplane and optical data communications. Due to continued process scaling and circuit innovations, today's CMOS serial link transceivers can achieve tens of Gb/s per pin. However, most of their reported power efficiency improves much slower than the rise of data rate. Therefore, aggregate I/O power is increasing and will exceed the power budget if the trend for more off-chip bandwidth is sustained. In this work, a system level statistical analysis of serial links is first described, and compares the link performance of Non-Return-to-Zero (2-PAM) with higher-order modulation (duobinary) signaling schemes. This method enables fast and accurate BER distribution simulation of serial link transceivers that include channel and circuit imperfections, such as finite pulse rise/fall time, duty cycle variation, and both receiver and transmitter forwarded-clock jitter. Second, in order to address link power efficiency, two test chips have been implemented. The first one describes a quad-lane, 6.4-7.2 Gb/s serial link receiver prototype using a forwarded clock architecture. A novel phase deskew scheme using injection-locked ring oscillators (ILRO) is proposed that achieves greater than one UI of phase shift for multiple clock phases, eliminating phase rotation and interpolation required in conventional architectures. Each receiver, optimized for power efficiency, consists of a low-power linear equalizer, four offset-cancelled quantizers for 1:4 demultiplexing, and an injection-locked ring oscillator coupled to a low-voltage swing, global clock distribution. Measurement results show a 6.4-7.2Gb/s data rate with BER < 10⁻¹² across 14 cm of PCB, and an 8Gb/s data rate through 4cm of PCB. Designed in a 1.2V, 90nm CMOS process, the ILRO achieves a wide tuning range from 1.6-2.6GHz. The total area of each receiver is 0.0174mm², resulting in a measured power efficiency of 0.6mW/Gb/s. Improving upon the first test chip, a second test chip for 8Gb/s forwarded clock serial link receivers exploits a low-power super-harmonic injection-locked ring oscillator for symmetric multi-phase local clock generation and deskewing. Further power reduction is achieved by designing most of the receiver circuits in the near-threshold region (0.6V supply), with the exception of only the global clock buffer, test buffers and synthesized digital test circuits at nominal 1V supply. At the architectural level, a 1:10 direct demultiplexing rate is chosen to achieve low supply operation by exploiting high-parallelism. Fabricated in 65nm CMOS technology, two receiver prototypes are integrated in this test chip, one without and the other with front-end boot-strapped S/Hs. Including the amortized power of global clock distribution, the proposed serial link receivers consume 1.3mW and 2mW respectively at 8Gb/s input data rate, achieving a power efficiency of 0.163mW/Gb/s and 0.25mW/Gb/s. Measurement results show both receivers achieve BER < 10⁻¹² across a 20-cm FR4 PCB channel

Application of advanced on-board processing concepts to future satellite communications systems: Bibliography

Abstracts are presented of a literature survey of reports concerning the application of signal processing concepts. Approximately 300 references are included

Design of High-Speed SerDes Transceiver for Chip-to-Chip Communications in CMOS Process

With the continuous increase of on-chip computation capacities and exponential growth of data-intensive applications, the high-speed data transmission through serial links has become the backbone for modern communication systems. To satisfy the massive data-exchanging requirement, the data rate of such serial links has been updated from several Gb/s to tens of Gb/s. Currently, the commercial standards such as Ethernet 400GbE, InfiniBand high data rate (HDR), and common electrical interface (CEI)-56G has been developing towards 40+ Gb/s. As the core component within these links, the transceiver chipset plays a fundamental role in balancing the operation speed, power consumption, area occupation, and operation range. Meanwhile, the CMOS process has become the dominant technology in modern transceiver chip fabrications due to its large-scale digital integration capability and aggressive pricing advantage. This research aims to explore advanced techniques that are capable of exploiting the maximum operation speed of the CMOS process, and hence provides potential solutions for 40+ Gb/s CMOS transceiver designs. The major contributions are summarized as follows. A low jitter ring-oscillator-based injection-locked clock multiplier (RILCM) with a hybrid frequency tracking loop that consists of a traditional phase-locked loop (PLL), a timing-adjusted loop, and a loop selection state-machine is implemented in 65-nm C-MOS process. In the ring voltage-controlled oscillator, a full-swing pseudo-differential delay cell is proposed to lower the device noise to phase noise conversion. To obtain high operation speed and high detection accuracy, a compact timing-adjusted phase detector tightly combined with a well-matched charge pump is designed. Meanwhile, a lock-loss detection and lock recovery is devised to endow the RILCM with a similar lock-acquisition ability as conventional PLL, thus excluding the initial frequency set- I up aid and preventing the potential lock-loss risk. The experimental results show that the figure-of-merit of the designed RILCM reaches -247.3 dB, which is better than previous RILCMs and even comparable to the large-area LC-ILCMs. The transmitter (TX) and receiver (RX) chips are separately designed and fab- ricated in 65-nm CMOS process. The transmitter chip employs a quarter-rate multi-multiplexer (MUX)-based 4-tap feed-forward equalizer (FFE) to pre-distort the output. To increase the maximum operating speed, a bandwidth-enhanced 4:1 MUX with the capability of eliminating charge-sharing effect is proposed. To produce the quarter-rate parallel data streams with appropriate delays, a compact latch array associated with an interleaved-retiming technique is designed. The receiver chip employs a two-stage continuous-time linear equalizer (CTLE) as the analog front-end and integrates an improved clock data recovery to extract the sampling clocks and retime the incoming data. To automatically balance the jitter tracking and jitter suppression, passive low-pass filters with adaptively-adjusted bandwidth are introduced into the data-sampling path. To optimize the linearity of the phase interpolation, a time-averaging-based compensating phase interpolator is proposed. For equalization, a combined TX-FFE and RX-CTLE is applied to compensate for the channel loss, where a low-cost edge-data correlation-based sign zero-forcing adaptation algorithm is proposed to automatically adjust the TX-FFE’s tap weights. Measurement results show that the fabricated transmitter/receiver chipset can deliver 40 Gb/s random data at a bit error rate of 16 dB loss at the half-baud frequency, while consuming a total power of 370 mW