Algorithmic techniques for physical design : macro placement and under-the-cell routing

With the increase of chip component density and new manufacturability constraints imposed by modern technology nodes, the role of algorithms for electronic design automation is key to the successful implementation of integrated circuits. Two of the critical steps in the physical design flows are macro placement and ensuring all design rules are honored after timing closure. This thesis proposes contributions to help in these stages, easing time-consuming manual steps and helping physical design engineers to obtain better layouts in reduced turnaround time. The first contribution is under-the-cell routing, a proposal to systematically connect standard cell components via lateral pins in the lower metal layers. The aim is to reduce congestion in the upper metal layers caused by extra metal and vias, decreasing the number of design rule violations. To allow cells to connect by abutment, a standard cell library is enriched with instances containing lateral pins in a pre-selected sharing track. Algorithms are proposed to maximize the numbers of connections via lateral connection by mapping placed cell instances to layouts with lateral pins, and proposing local placement modifications to increase the opportunities for such connections. Experimental results show a significant decrease in the number of pins, vias, and in number of design rule violations, with negligible impact on wirelength and timing. The second contribution, done in collaboration with eSilicon (a leading ASIC design company), is the creation of HiDaP, a macro placement tool for modern industrial designs. The proposed approach follows a multilevel scheme to floorplan hierarchical blocks, composed of macros and standard cells. By exploiting RTL information available in the netlist, the dataflow affinity between these blocks is modeled and minimized to find a macro placement with good wirelength and timing properties. The approach is further extended to allow additional engineer input, such as preferred macro locations, and also spectral and force methods to guide the floorplanning search. Experimental results show that the layouts generated by HiDaP outperforms those obtained by a state-of-the-art EDA physical design software, with similar wirelength and better timing when compared to manually designed tape-out ready macro placements. Layouts obtained by HiDaP have successfully been brought to near timing closure with one to two rounds of small modifications by physical design engineers. HiDaP has been fully integrated in the design flows of the company and its development remains an ongoing effort.A causa de l'increment de la densitat de components en els xip i les noves restriccions de disseny imposades pels últims nodes de fabricació, el rol de l'algorísmia en l'automatització del disseny electrònic ha esdevingut clau per poder implementar circuits integrats. Dos dels passos crucials en el procés de disseny físic és el placement de macros i assegurar la correcció de les regles de disseny un cop les restriccions de timing del circuit són satisfetes. Aquesta tesi proposa contribucions per ajudar en aquests dos reptes, facilitant laboriosos passos manuals en el procés i ajudant als enginyers de disseny físic a obtenir millors resultats en menys temps. La primera contribució és el routing "under-the-cell", una proposta per connectar cel·les estàndard usant pins laterals en les capes de metall inferior de manera sistemàtica. L'objectiu és reduir la congestió en les capes de metall superior causades per l'ús de metall i vies, i així disminuir el nombre de violacions de regles de disseny. Per permetre la connexió lateral de cel·les, estenem una llibreria de cel·les estàndard amb dissenys que incorporen connexions laterals. També proposem modificacions locals al placement per permetre explotar aquest tipus de connexions més sovint. Els resultats experimentals mostren una reducció significativa en el nombre de pins, vies i nombre de violacions de regles de disseny, amb un impacte negligible en wirelength i timing. La segona contribució, desenvolupada en col·laboració amb eSilicon (una empresa capdavantera en disseny ASIC), és el desenvolupament de HiDaP, una eina de macro placement per a dissenys industrials actuals. La proposta segueix un procés multinivell per fer el floorplan de blocks jeràrquics, formats per macros i cel·les estàndard. Mitjançant la informació RTL disponible en la netlist, l'afinitat de dataflow entre els mòduls es modela i minimitza per trobar macro placements amb bones propietats de wirelength i timing. La proposta també incorpora la possibilitat de rebre input addicional de l'enginyer, com ara suggeriments de les posicions de les macros. Finalment, també usa mètodes espectrals i de forçes per guiar la cerca de floorplans. Els resultats experimentals mostren que els dissenys generats amb HiDaP són millors que els obtinguts per eines comercials capdavanteres de EDA. Els resultats també mostren que els dissenys presentats poden obtenir un wirelength similar i millor timing que macro placements obtinguts manualment, usats per fabricació. Alguns dissenys obtinguts per HiDaP s'han dut fins a timing-closure en una o dues rondes de modificacions incrementals per part d'enginyers de disseny físic. L'eina s'ha integrat en el procés de disseny de eSilicon i el seu desenvolupament continua més enllà de les aportacions a aquesta tesi.Postprint (published version

Algorithmic techniques for physical design : macro placement and under-the-cell routing

With the increase of chip component density and new manufacturability constraints imposed by modern technology nodes, the role of algorithms for electronic design automation is key to the successful implementation of integrated circuits. Two of the critical steps in the physical design flows are macro placement and ensuring all design rules are honored after timing closure. This thesis proposes contributions to help in these stages, easing time-consuming manual steps and helping physical design engineers to obtain better layouts in reduced turnaround time. The first contribution is under-the-cell routing, a proposal to systematically connect standard cell components via lateral pins in the lower metal layers. The aim is to reduce congestion in the upper metal layers caused by extra metal and vias, decreasing the number of design rule violations. To allow cells to connect by abutment, a standard cell library is enriched with instances containing lateral pins in a pre-selected sharing track. Algorithms are proposed to maximize the numbers of connections via lateral connection by mapping placed cell instances to layouts with lateral pins, and proposing local placement modifications to increase the opportunities for such connections. Experimental results show a significant decrease in the number of pins, vias, and in number of design rule violations, with negligible impact on wirelength and timing. The second contribution, done in collaboration with eSilicon (a leading ASIC design company), is the creation of HiDaP, a macro placement tool for modern industrial designs. The proposed approach follows a multilevel scheme to floorplan hierarchical blocks, composed of macros and standard cells. By exploiting RTL information available in the netlist, the dataflow affinity between these blocks is modeled and minimized to find a macro placement with good wirelength and timing properties. The approach is further extended to allow additional engineer input, such as preferred macro locations, and also spectral and force methods to guide the floorplanning search. Experimental results show that the layouts generated by HiDaP outperforms those obtained by a state-of-the-art EDA physical design software, with similar wirelength and better timing when compared to manually designed tape-out ready macro placements. Layouts obtained by HiDaP have successfully been brought to near timing closure with one to two rounds of small modifications by physical design engineers. HiDaP has been fully integrated in the design flows of the company and its development remains an ongoing effort.A causa de l'increment de la densitat de components en els xip i les noves restriccions de disseny imposades pels últims nodes de fabricació, el rol de l'algorísmia en l'automatització del disseny electrònic ha esdevingut clau per poder implementar circuits integrats. Dos dels passos crucials en el procés de disseny físic és el placement de macros i assegurar la correcció de les regles de disseny un cop les restriccions de timing del circuit són satisfetes. Aquesta tesi proposa contribucions per ajudar en aquests dos reptes, facilitant laboriosos passos manuals en el procés i ajudant als enginyers de disseny físic a obtenir millors resultats en menys temps. La primera contribució és el routing "under-the-cell", una proposta per connectar cel·les estàndard usant pins laterals en les capes de metall inferior de manera sistemàtica. L'objectiu és reduir la congestió en les capes de metall superior causades per l'ús de metall i vies, i així disminuir el nombre de violacions de regles de disseny. Per permetre la connexió lateral de cel·les, estenem una llibreria de cel·les estàndard amb dissenys que incorporen connexions laterals. També proposem modificacions locals al placement per permetre explotar aquest tipus de connexions més sovint. Els resultats experimentals mostren una reducció significativa en el nombre de pins, vies i nombre de violacions de regles de disseny, amb un impacte negligible en wirelength i timing. La segona contribució, desenvolupada en col·laboració amb eSilicon (una empresa capdavantera en disseny ASIC), és el desenvolupament de HiDaP, una eina de macro placement per a dissenys industrials actuals. La proposta segueix un procés multinivell per fer el floorplan de blocks jeràrquics, formats per macros i cel·les estàndard. Mitjançant la informació RTL disponible en la netlist, l'afinitat de dataflow entre els mòduls es modela i minimitza per trobar macro placements amb bones propietats de wirelength i timing. La proposta també incorpora la possibilitat de rebre input addicional de l'enginyer, com ara suggeriments de les posicions de les macros. Finalment, també usa mètodes espectrals i de forçes per guiar la cerca de floorplans. Els resultats experimentals mostren que els dissenys generats amb HiDaP són millors que els obtinguts per eines comercials capdavanteres de EDA. Els resultats també mostren que els dissenys presentats poden obtenir un wirelength similar i millor timing que macro placements obtinguts manualment, usats per fabricació. Alguns dissenys obtinguts per HiDaP s'han dut fins a timing-closure en una o dues rondes de modificacions incrementals per part d'enginyers de disseny físic. L'eina s'ha integrat en el procés de disseny de eSilicon i el seu desenvolupament continua més enllà de les aportacions a aquesta tesi

Adaptive Integrated Circuit Design for Variation Resilience and Security

The past few decades witness the burgeoning development of integrated circuit in terms of process technology scaling. Along with the tremendous benefits coming from the scaling, challenges are also presented in various stages. During the design time, the complexity of developing a circuit with millions to billions of smaller size transistors is extended after the variations are taken into account. The difficulty of analyzing these nondeterministic properties makes the allocation scheme of redundant resource hardly work in a cost-efficient way. Besides fabrication variations, analog circuits are suffered from severe performance degradations owing to their physical attributes which are vulnerable to aging effects. As such, the post-silicon calibration approach gains increasing attentions to compensate the performance mismatch. For the user-end applications, additional system failures result from the pirated and counterfeited devices provided by the untrusted semiconductor supply chain. Again analog circuits show their weakness to this threat due to the shortage of piracy avoidance techniques. In this dissertation, we propose three adaptive integrated circuit designs to overcome these challenges respectively. The first one investigates the variability-aware gate implementation with the consideration of the overhead control of adaptivity assignment. This design improves the variation resilience typically for digital circuits while optimizing the power consumption and timing yield. The second design is implemented as a self-validation system for the calibration of diverse analog circuits. The system is completely integrated on chip to enhance the convenience without external assistance. In the last design, a classic analog component is further studied to establish the configurable locking mechanism for analog circuits. The use of Satisfiability Modulo Theories addresses the difficulty of searching the unique unlocking pattern of non-Boolean variables

Reliable chip design from low powered unreliable components

The pace of technological improvement of the semiconductor market is driven by Moore’s Law, enabling chip transistor density to double every two years. The transistors would continue to decline in cost and size but increase in power. The continuous transistor scaling and extremely lower power constraints in modern Very Large Scale Integrated(VLSI) chips can potentially supersede the benefits of the technology shrinking due to reliability issues. As VLSI technology scales into nanoscale regime, fundamental physical limits are approached, and higher levels of variability, performance degradation, and higher rates of manufacturing defects are experienced. Soft errors, which traditionally affected only the memories, are now also resulting in logic circuit reliability degradation. A solution to these limitations is to integrate reliability assessment techniques into the Integrated Circuit(IC) design flow. This thesis investigates four aspects of reliability driven circuit design: a)Reliability estimation; b) Reliability optimization; c) Fault-tolerant techniques, and d) Delay degradation analysis. To guide the reliability driven synthesis and optimization of combinational circuits, highly accurate probability based reliability estimation methodology christened Conditional Probabilistic Error Propagation(CPEP) algorithm is developed to compute the impact of gate failures on the circuit output. CPEP guides the proposed rewriting based logic optimization algorithm employing local transformations. The main idea behind this methodology is to replace parts of the circuit with functionally equivalent but more reliable counterparts chosen from a precomputed subset of Negation-Permutation-Negation(NPN) classes of 4-variable functions. Cut enumeration and Boolean matching driven by reliability-aware optimization algorithm are used to identify the best possible replacement candidates. Experiments on a set of MCNC benchmark circuits and 8051 functional microcontroller units indicate that the proposed framework can achieve up to 75% reduction of output error probability. On average, about 14% SER reduction is obtained at the expense of very low area overhead of 6.57% that results in 13.52% higher power consumption. The next contribution of the research describes a novel methodology to design fault tolerant circuitry by employing the error correction codes known as Codeword Prediction Encoder(CPE). Traditional fault tolerant techniques analyze the circuit reliability issue from a static point of view neglecting the dynamic errors. In the context of communication and storage, the study of novel methods for reliable data transmission under unreliable hardware is an increasing priority. The idea of CPE is adapted from the field of forward error correction for telecommunications focusing on both encoding aspects and error correction capabilities. The proposed Augmented Encoding solution consists of computing an augmented codeword that contains both the codeword to be transmitted on the channel and extra parity bits. A Computer Aided Development(CAD) framework known as CPE simulator is developed providing a unified platform that comprises a novel encoder and fault tolerant LDPC decoders. Experiments on a set of encoders with different coding rates and different decoders indicate that the proposed framework can correct all errors under specific scenarios. On average, about 1000 times improvement in Soft Error Rate(SER) reduction is achieved. Last part of the research is the Inverse Gaussian Distribution(IGD) based delay model applicable to both combinational and sequential elements for sub-powered circuits. The Probability Density Function(PDF) based delay model accurately captures the delay behavior of all the basic gates in the library database. The IGD model employs these necessary parameters, and the delay estimation accuracy is demonstrated by evaluating multiple circuits. Experiments results indicate that the IGD based approach provides a high matching against HSPICE Monte Carlo simulation results, with an average error less than 1.9% and 1.2% for the 8-bit Ripple Carry Adder(RCA), and 8-bit De-Multiplexer(DEMUX) and Multiplexer(MUX) respectively

Embedding Logic and Non-volatile Devices in CMOS Digital Circuits for Improving Energy Efficiency

abstract: Static CMOS logic has remained the dominant design style of digital systems for more than four decades due to its robustness and near zero standby current. Static CMOS logic circuits consist of a network of combinational logic cells and clocked sequential elements, such as latches and flip-flops that are used for sequencing computations over time. The majority of the digital design techniques to reduce power, area, and leakage over the past four decades have focused almost entirely on optimizing the combinational logic. This work explores alternate architectures for the flip-flops for improving the overall circuit performance, power and area. It consists of three main sections. First, is the design of a multi-input configurable flip-flop structure with embedded logic. A conventional D-type flip-flop may be viewed as realizing an identity function, in which the output is simply the value of the input sampled at the clock edge. In contrast, the proposed multi-input flip-flop, named PNAND, can be configured to realize one of a family of Boolean functions called threshold functions. In essence, the PNAND is a circuit implementation of the well-known binary perceptron. Unlike other reconfigurable circuits, a PNAND can be configured by simply changing the assignment of signals to its inputs. Using a standard cell library of such gates, a technology mapping algorithm can be applied to transform a given netlist into one with an optimal mixture of conventional logic gates and threshold gates. This approach was used to fabricate a 32-bit Wallace Tree multiplier and a 32-bit booth multiplier in 65nm LP technology. Simulation and chip measurements show more than 30% improvement in dynamic power and more than 20% reduction in core area. The functional yield of the PNAND reduces with geometry and voltage scaling. The second part of this research investigates the use of two mechanisms to improve the robustness of the PNAND circuit architecture. One is the use of forward and reverse body biases to change the device threshold and the other is the use of RRAM devices for low voltage operation. The third part of this research focused on the design of flip-flops with non-volatile storage. Spin-transfer torque magnetic tunnel junctions (STT-MTJ) are integrated with both conventional D-flipflop and the PNAND circuits to implement non-volatile logic (NVL). These non-volatile storage enhanced flip-flops are able to save the state of system locally when a power interruption occurs. However, manufacturing variations in the STT-MTJs and in the CMOS transistors significantly reduce the yield, leading to an overly pessimistic design and consequently, higher energy consumption. A detailed analysis of the design trade-offs in the driver circuitry for performing backup and restore, and a novel method to design the energy optimal driver for a given yield is presented. Efficient designs of two nonvolatile flip-flop (NVFF) circuits are presented, in which the backup time is determined on a per-chip basis, resulting in minimizing the energy wastage and satisfying the yield constraint. To achieve a yield of 98%, the conventional approach would have to expend nearly 5X more energy than the minimum required, whereas the proposed tunable approach expends only 26% more energy than the minimum. A non-volatile threshold gate architecture NV-TLFF are designed with the same backup and restore circuitry in 65nm technology. The embedded logic in NV-TLFF compensates performance overhead of NVL. This leads to the possibility of zero-overhead non-volatile datapath circuits. An 8-bit multiply-and- accumulate (MAC) unit is designed to demonstrate the performance benefits of the proposed architecture. Based on the results of HSPICE simulations, the MAC circuit with the proposed NV-TLFF cells is shown to consume at least 20% less power and area as compared to the circuit designed with conventional DFFs, without sacrificing any performance.Dissertation/ThesisDoctoral Dissertation Electrical Engineering 201

Custom Cell Placement Automation for Asynchronous VLSI

Asynchronous Very-Large-Scale-Integration (VLSI) integrated circuits have demonstrated many advantages over their synchronous counterparts, including low power consumption, elastic pipelining, robustness against manufacturing and temperature variations, etc. However, the lack of dedicated electronic design automation (EDA) tools, especially physical layout automation tools, largely limits the adoption of asynchronous circuits. Existing commercial placement tools are optimized for synchronous circuits, and require a standard cell library provided by semiconductor foundries to complete the physical design. The physical layouts of cells in this library have the same height to simplify the placement problem and the power distribution network. Although the standard cell methodology also works for asynchronous designs, the performance is inferior compared with counterparts designed using the full-custom design methodology. To tackle this challenge, we propose a gridded cell layout methodology for asynchronous circuits, in which the cell height and cell width can be any integer multiple of two grid values. The gridded cell approach combines the shape regularity of standard cells with the size flexibility of full-custom layouts. Therefore, this approach can achieve a better space utilization ratio and lower wire length for asynchronous designs. Experiments have shown that the gridded cell placement approach reduces area without impacting the routability. We have also used this placer to tape out a chip in a 65nm process technology, demonstrating that our placer generates design-rule clean results

VLSI Design

This book provides some recent advances in design nanometer VLSI chips. The selected topics try to present some open problems and challenges with important topics ranging from design tools, new post-silicon devices, GPU-based parallel computing, emerging 3D integration, and antenna design. The book consists of two parts, with chapters such as: VLSI design for multi-sensor smart systems on a chip, Three-dimensional integrated circuits design for thousand-core processors, Parallel symbolic analysis of large analog circuits on GPU platforms, Algorithms for CAD tools VLSI design, A multilevel memetic algorithm for large SAT-encoded problems, etc

Exploring Spin-transfer-torque devices and memristors for logic and memory applications

As scaling CMOS devices is approaching its physical limits, researchers have begun exploring newer devices and architectures to replace CMOS. Due to their non-volatility and high density, Spin Transfer Torque (STT) devices are among the most prominent candidates for logic and memory applications. In this research, we first considered a new logic style called All Spin Logic (ASL). Despite its advantages, ASL consumes a large amount of static power; thus, several optimizations can be performed to address this issue. We developed a systematic methodology to perform the optimizations to ensure stable operation of ASL. Second, we investigated reliable design of STT-MRAM bit-cells and addressed the conflicting read and write requirements, which results in overdesign of the bit-cells. Further, a Device/Circuit/Architecture co-design framework was developed to optimize the STT-MRAM devices by exploring the design space through jointly considering yield enhancement techniques at different levels of abstraction. Recent advancements in the development of memristive devices have opened new opportunities for hardware implementation of non-Boolean computing. To this end, the suitability of memristive devices for swarm intelligence algorithms has enabled researchers to solve a maze in hardware. In this research, we utilized swarm intelligence of memristive networks to perform image edge detection. First, we proposed a hardware-friendly algorithm for image edge detection based on ant colony. Next, we designed the image edge detection algorithm using memristive networks

Low Power Design Techniques for Digital Logic Circuits.

With the rapid increase in the density and the size of chips and systems, area and power dissipationbecome critical concern in Very Large Scale Integrated (VLSI) circuit design. Low powerdesign techniques are essential for today's VLSI industry. The history of symbolic logic and sometypical techniques for finite state machine (FSM) logic synthesis are reviewed.The state assignment is used to optimize area and power dissipation for FSMs. Two costfunctions, targeting area and power, are presented. The Genetic Algorithm (GA) is used to searchfor a good state assignment to minimize the cost functions. The algorithm has been implementedin C. The program can produce better results than NOVA, which is integrated into SIS by DCBerkeley, and other publications both in area and power tested by MCNC benchmarks.Flip-flops are the core components of FSMs. The reduction of power dissipation from flip-flopscan save power for digital systems significantly. Three new kinds of flip-flops, called differentialCMOS single edge-triggered flip-flop with clock gating, double edge-triggered and multiple valuedflip-flops employing multiple valued clocks, are proposed. All circuits are simulated using PSpice.Most researchers have focused on developing low-power techniques in AND/OR or NAND& NOR based circuits. The low power techniques for AND /XOR based circuits are still intheir early stage of development. To implement a complex function involving many inputs,a form of decomposition into smaller subfunctions is required such that the subfunctions fitinto the primitive elements to be used in the implementation. Best polarity based XOR gatedecomposition technique has been developed, which targets low power using Huffman algorithm.Compared to the published results, the proposed method shows considerable improvement inpower dissipation. Further, Boolean functions can be expressed by Fixed Polarity Reed-Muller(FPRM) forms. Based on polarity transformation, an algorithm is developed and implementedin C language which can find the best polarity for power and area optimization. Benchmarkexamples of up to 21 inputs run on a personal computer are given

Design Automation and Application for Emerging Reconfigurable Nanotechnologies

In the last few decades, two major phenomena have revolutionized the electronic industry – the ever-increasing dependence on electronic circuits and the Complementary Metal Oxide Semiconductor (CMOS) downscaling. These two phenomena have been complementing each other in a way that while electronics, in general, have demanded more computations per functional unit, CMOS downscaling has aptly supported such needs. However, while the computational demand is still rising exponentially, CMOS downscaling is reaching its physical limits. Hence, the need to explore viable emerging nanotechnologies is more imperative than ever. This thesis focuses on streamlining the existing design automation techniques for a class of emerging reconfigurable nanotechnologies. Transistors based on this technology exhibit duality in conduction, i.e. they can be configured dynamically either as a p-type or an n-type device on the application of an external bias. Owing to this dynamic reconfiguration, these transistors are also referred to as Reconfigurable Field-Effect Transistors (RFETs). Exploring and developing new technologies just like CMOS, require tackling two main challenges – first, design automation flow has to be modified to enable tailor- made circuit designs. Second, possible application opportunities should be explored where such technologies can outsmart the existing CMOS technologies. This thesis targets the above two objectives for emerging reconfigurable nanotechnologies by proposing approaches for enabling an Electronic Design Automation (EDA) flow for circuits based on RFETs and exploring hardware security as an application that exploits the transistor-level dynamic reconfiguration offered by this technology. This thesis explains the bottom-up approach adopted to propose a logic synthesis flow by identifying new logic gates and circuit design paradigms that can particularly exploit the dynamic reconfiguration offered by these novel nanotechnologies. This led to the subsequent need of finding natural Boolean logic abstraction for emerging reconfigurable nanotechnologies as it is shown that the existing abstraction of negative unate logic for CMOS technologies is sub-optimal for RFETs-based circuits. In this direction, it has been shown that duality in Boolean logic is a natural abstraction for this technology and can truly represent the duality in conduction offered by individual transistors. Finding this abstraction paved the way for defining suitable primitives and proposing various algorithms for logic synthesis and technology mapping. The following step is to explore compatible physical synthesis flow for emerging reconfigurable nanotechnologies. Using silicon nanowire-based RFETs, .lef and .lib files have been provided which can provide an end-to-end flow to generate .GDSII file for circuits exclusively based on RFETs. Additionally, new approaches have been explored to improve placement and routing for circuits based on reconfigurable nanotechnologies. It has been demonstrated how these approaches led to superior results as compared to the native flow meant for CMOS. Lastly, the unique property of transistor-level reconfiguration offered by RFETs is utilized to implement efficient Intellectual Property (IP) protection schemes against adversarial attacks. The ability to control the conduction of individual transistors can be argued as one of the impactful features of this technology and suitably fits into the paradigm of security measures. Prior security schemes based on CMOS technology often come with large overheads in terms of area, power, and delay. In contrast, RFETs-based hardware security measures such as logic locking, split manufacturing, etc. proposed in this thesis, demonstrate affordable security solutions with low overheads. Overall, this thesis lays a strong foundation for the two main objectives – design automation, and hardware security as an application, to push emerging reconfigurable nanotechnologies for commercial integration. Additionally, contributions done in this thesis are made available under open-source licenses so as to foster new research directions and collaborations.:Abstract List of Figures List of Tables 1 Introduction 1.1 What are emerging reconfigurable nanotechnologies? 1.2 Why does this technology look so promising? 1.3 Electronics Design Automation 1.4 The game of see-saw: key challenges vs benefits for emerging reconfigurable nanotechnologies 1.4.1 Abstracting ambipolarity in logic gate designs 1.4.2 Enabling electronic design automation for RFETs 1.4.3 Enhanced functionality: a suitable fit for hardware security applications 1.5 Research questions 1.6 Entire RFET-centric EDA Flow 1.7 Key Contributions and Thesis Organization 2 Preliminaries 2.1 Reconfigurable Nanotechnology 2.1.1 1D devices 2.1.2 2D devices 2.1.3 Factors favoring circuit-flexibility 2.2 Feasibility aspects of RFET technology 2.3 Logic Synthesis Preliminaries 2.3.1 Circuit Model 2.3.2 Boolean Algebra 2.3.3 Monotone Function and the property of Unateness 2.3.4 Logic Representations 3 Exploring Circuit Design Topologies for RFETs 3.1 Contributions 3.2 Organization 3.3 Related Works 3.4 Exploring design topologies for combinational circuits: functionality-enhanced logic gates 3.4.1 List of Combinational Functionality-Enhanced Logic Gates based on RFETs 3.4.2 Estimation of gate delay using the logical effort theory 3.5 Invariable design of Inverters 3.6 Sequential Circuits 3.6.1 Dual edge-triggered TSPC-based D-flip flop 3.6.2 Exploiting RFET’s ambipolarity for metastability 3.7 Evaluations 3.7.1 Evaluation of combinational logic gates 3.7.2 Novel design of 1-bit ALU 3.7.3 Comparison of the sequential circuit with an equivalent CMOS-based design 3.8 Concluding remarks 4 Standard Cells and Technology Mapping 4.1 Contributions 4.2 Organization 4.3 Related Work 4.4 Standard cells based on RFETs 4.4.1 Interchangeable Pull-Up and Pull-Down Networks 4.4.2 Reconfigurable Truth-Table 4.5 Distilling standard cells 4.6 HOF-based Technology Mapping Flow for RFETs-based circuits 4.6.1 Area adjustments through inverter sharings 4.6.2 Technology Mapping Flow 4.6.3 Realizing Parameters For The Generic Library 4.6.4 Defining RFETs-based Genlib for HOF-based mapping 4.7 Experiments 4.7.1 Experiment 1: Distilling standard-cells from a benchmark suite 4.7.2 Experiment 2A: HOF-based mapping . 4.7.3 Experiment 2B: Using the distilled standard-cells during mapping 4.8 Concluding Remarks 5 Logic Synthesis with XOR-Majority Graphs 5.1 Contributions 5.2 Organization 5.3 Motivation 5.4 Background and Preliminaries 5.4.1 Terminologies 5.4.2 Self-duality in NPN classes 5.4.3 Majority logic synthesis 5.4.4 Earlier work on XMG 5.4.5 Classification of Boolean functions 5.5 Preserving Self-Duality 5.5.1 During logic synthesis 5.5.2 During versatile technology mapping 5.6 Advanced Logic synthesis techniques 5.6.1 XMG resubstitution 5.6.2 Exact XMG rewriting 5.7 Logic representation-agnostic Mapping 5.7.1 Versatile Mapper 5.7.2 Support of supergates 5.8 Creating Self-dual Benchmarks 5.9 Experiments 5.9.1 XMG-based Flow 5.9.2 Experimental Setup 5.9.3 Synthetic self-dual benchmarks 5.9.4 Cryptographic benchmark suite 5.10 Concluding remarks and future research directions 6 Physical synthesis flow and liberty generation 6.1 Contributions 6.2 Organization 6.3 Background and Related Work 6.3.1 Related Works 6.3.2 Motivation 6.4 Silicon Nanowire Reconfigurable Transistors 6.5 Layouts for Logic Gates 6.5.1 Layouts for Static Functional Logic Gates 6.5.2 Layout for Reconfigurable Logic Gate 6.6 Table Model for Silicon Nanowire RFETs 6.7 Exploring Approaches for Physical Synthesis 6.7.1 Using the Standard Place & Route Flow 6.7.2 Open-source Flow 6.7.3 Concept of Driver Cells 6.7.4 Native Approach 6.7.5 Island-based Approach 6.7.6 Utilization Factor 6.7.7 Placement of the Island on the Chip 6.8 Experiments 6.8.1 Preliminary comparison with CMOS technology 6.8.2 Evaluating different physical synthesis approaches 6.9 Results and discussions 6.9.1 Parameters Which Affect The Area 6.9.2 Use of Germanium Nanowires Channels 6.10 Concluding Remarks 7 Polymporphic Primitives for Hardware Security 7.1 Contributions 7.2 Organization 7.3 The Shift To Explore Emerging Technologies For Security 7.4 Background 7.4.1 IP protection schemes 7.4.2 Preliminaries 7.5 Security Promises 7.5.1 RFETs for logic locking (transistor-level locking) 7.5.2 RFETs for split manufacturing 7.6 Security Vulnerabilities 7.6.1 Realization of short-circuit and open-circuit scenarios in an RFET-based inverter 7.6.2 Circuit evaluation on sub-circuits 7.6.3 Reliability concerns: A consequence of short-circuit scenario 7.6.4 Implication of the proposed security vulnerability 7.7 Analytical Evaluation 7.7.1 Investigating the security promises 7.7.2 Investigating the security vulnerabilities 7.8 Concluding remarks and future research directions 8 Conclusion 8.1 Concluding Remarks 8.2 Directions for Future Work Appendices A Distilling standard-cells B RFETs-based Genlib C Layout Extraction File (.lef) for Silicon Nanowire-based RFET D Liberty (.lib) file for Silicon Nanowire-based RFET