Design and modelling of clock and data recovery integrated circuit in 130 nm CMOS technology for 10 Gb/s serial data communications

This thesis describes the design and implementation of a fully monolithic 10 Gb/s phase and frequency-locked loop based clock and data recovery (PFLL-CDR) integrated circuit, as well as the Verilog-A modeling of an asynchronous serial link based chip to chip communication system incorporating the proposed concept. The proposed design was implemented and fabricated using the 130 nm CMOS technology offered by UMC (United Microelectronics Corporation). Different PLL-based CDR circuits topologies were investigated in terms of architecture and speed. Based on the investigation, we proposed a new concept of quarter-rate (i.e. the clocking speed in the circuit is 2.5 GHz for 10 Gb/s data rate) and dual-loop topology which consists of phase-locked and frequency-locked loop. The frequency-locked loop (FLL) operates independently from the phase-locked loop (PLL), and has a highly-desired feature that once the proper frequency has been acquired, the FLL is automatically disabled and the PLL will take over to adjust the clock edges approximately in the middle of the incoming data bits for proper sampling. Another important feature of the proposed quarter-rate concept is the inherent 1-to-4 demultiplexing of the input serial data stream. A new quarter-rate phase detector based on the non-linear early-late phase detector concept has been used to achieve the multi-Giga bit/s speed and to eliminate the need of the front-end data pre-processing (edge detecting) units usually associated with the conventional CDR circuits. An eight-stage differential ring oscillator running at 2.5 GHz frequency center was used for the voltage-controlled oscillator (VCO) to generate low-jitter multi-phase clock signals. The transistor level simulation results demonstrated excellent performances in term of locking speed and power consumption. In order to verify the accuracy of the proposed quarter-rate concept, a clockless asynchronous serial link incorporating the proposed concept and communicating two chips at 10 Gb/s has been modelled at gate level using the Verilog-A language and time-domain simulated

Design of an Active Harmonic Rejection N-Path Filter for Highly Tunable RF Channel Selection

As the number of wireless devices in the world increases, so does the demand for flexible radio receiver architectures capable of operating over a wide range of frequencies and communication protocols. The resonance-based channel-select filters used in traditional radio architectures have a fixed frequency response, making them poorly suited for such a receiver. The N-path filter is based on 1960s technology that has received renewed interest in recent years for its application as a linear high Q filter at radio frequencies. N-path filters use passive mixers to apply a frequency transformation to a baseband low-pass filter in order to achieve a high-Q band-pass response at high frequencies. The clock frequency determines the center frequency of the band-pass filter, which makes the filter highly tunable over a broad frequency range. Issues with harmonic transfer and poor attenuation limit the feasibility of using N-path filters in practice. The goal of this thesis is to design an integrated active N-path filter that improves upon the passive N-path filter’s poor harmonic rejection and limited outof- band attenuation. The integrated circuit (IC) is implemented using the CMRF8SF 130nm CMOS process. The design uses a multi-phase clock generation circuit to implement a harmonic rejection mixer in order to suppress the 3rd and 5th harmonic. The completed active N-path filter has a tuning range of 200MHz to 1GHz and the out-ofband attenuation exceeds 60dB throughout this range. The frequency response exhibits a 14.7dB gain at the center frequency and a -3dB bandwidth of 6.8MHz

DESIGN AND CHARACTERIZATION OF LOW-POWER LOW-NOISE ALLDIGITAL SERIAL LINK FOR POINT-TO-POINT COMMUNICATION IN SOC

The fully-digital implementation of serial links has recently emerged as a viable alternative to their classical analogue counterpart. Indeed, reducing the analogue content in favour of expanding the digital content becomes more attractive due to the ability to achieve less power consumption, less sensitivity to the noise and better scalability across multiple technologies and platforms with inconsiderable modifications. In addition, describing the circuit in hardware description languages gives it a high flexibility to program all design parameters in a very short time compared with the analogue designs which need to be re-designed at transistor level for any parameter change. This can radically reduce cost and time-to-market by saving a significant amount of development time. However, beside these considerable advantages, the fully-digital architecture poses several design challenges

Algorithms and VLSI architectures for parametric additive synthesis

A parametric additive synthesis approach to sound synthesis is advantageous as it can model sounds in a large scale manner, unlike the classical sinusoidal additive based synthesis paradigms. It is known that a large body of naturally occurring sounds are resonant in character and thus fit the concept well. This thesis is concerned with the computational optimisation of a super class of form ant synthesis which extends the sinusoidal parameters with a spread parameter known as band width. Here a modified formant algorithm is introduced which can be traced back to work done at IRCAM, Paris. When impulse driven, a filter based approach to modelling a formant limits the computational work-load. It is assumed that the filter's coefficients are fixed at initialisation, thus avoiding interpolation which can cause the filter to become chaotic. A filter which is more complex than a second order section is required. Temporal resolution of an impulse generator is achieved by using a two stage polyphase decimator which drives many filterbanks. Each filterbank describes one formant and is composed of sub-elements which allow variation of the formant’s parameters. A resource manager is discussed to overcome the possibility of all sub- banks operating in unison. All filterbanks for one voice are connected in series to the impulse generator and their outputs are summed and scaled accordingly. An explorative study of number systems for DSP algorithms and their architectures is investigated. I invented a new theoretical mechanism for multi-level logic based DSP. Its aims are to reduce the number of transistors and to increase their functionality. A review of synthesis algorithms and VLSI architectures are discussed in a case study between a filter based bit-serial and a CORDIC based sinusoidal generator. They are both of similar size, but the latter is always guaranteed to be stable

Architecture FPGA améliorée et flot de conception pour une reconfiguration matérielle en ligne efficace

The self-reconfiguration capabilities of modern FPGA architectures pave the way for dynamic applications able to adapt to transient events. The CAD flows of modern architectures are nowadays mature but limited by the constraints induced by the complexity of FPGA circuits. In this thesis, multiple contributions are developed to propose an FPGA architecture supporting the dynamic placement of hardware tasks. First, an intermediate representation of these tasks configuration data, independent from their final position, is presented. This representation allows to compress the task data up to 11x with regard to its conventional raw counterpart. An accompanying CAD flow, based on state-of-the-art tools, is proposed to generate relocatable tasks from a high-level description. Then, the online behavior of this mechanism is studied. Two algorithms allowing to decode and create in real-time the conventional bit-stream are described. In addition, an enhancement of the FPGA interconnection network is proposedto increase the placement flexibility of heterogeneous tasks, at the cost of a 10% increase in average of the critical path delay. Eventually, a configurable substitute to the configuration memory found in FPGAs is studied to ease their partial reconfiguration.Les capacités d'auto-reconfiguration des architectures FPGA modernes ouvrent la voie à des applications dynamiques capables d'adapter leur fonctionnement pour répondre à des évènements ponctuels. Les flots de reconfiguration des architectures commerciales sont aujourd'hui aboutis mais limités par des contraintes inhérentes à la complexité de ces circuits. Dans cette thèse, plusieurs contributions sont avancées afin de proposer une architecture FPGA reconfigurable permettant le placement dynamique de tâches matérielles. Dans un premier temps, une représentation intermédiaire des données de configuration de ces tâches, indépendante de leur positionnement final, est présentée. Cette représentation permet notamment d'atteindre des taux de compression allant jusqu'à 11x par rapport à la représentation brute d'une tâche. Un flot de conception basé sur des outils de l'état de l'art accompagne cette représentation et génère des tâches relogeables à partir d'une description haut-niveau. Ensuite, le comportement en ligne de ce mécanisme est étudié. Deux algorithmes permettant le décodage de ces tâches et la génération en temps-réel des données de configuration propres à l'architectures son décrits. Par ailleurs, une amélioration du réseau d'interconnexion d'une architecture FPGA est proposée pour accroître la flexibilité du placement de tâches hétérogènes, avec une augmentation de 10% en moyenne du délai du chemin critique. Enfin, une alternative programmable aux mémoires de configuration de ces circuits est étudiée pour faciliter leur reconfiguration partielle

1999 Flight Mechanics Symposium

This conference publication includes papers and abstracts presented at the Flight Mechanics Symposium held on May 18-20, 1999. Sponsored by the Guidance, Navigation and Control Center of Goddard Space Flight Center, this symposium featured technical papers on a wide range of issues related to orbit-attitude prediction, determination, and control; attitude sensor calibration; attitude determination error analysis; attitude dynamics; and orbit decay and maneuver strategy. Government, industry, and the academic community participated in the preparation and presentation of these papers

Study, optimization and silicon implementation of a smart high-voltage conditioning circuit for electrostatic vibration energy harvesting system

La récupération de l'énergie des vibrations est un concept relativement nouveau qui peut être utilisé dans l'alimentation des dispositifs embarqués de puissance à micro-échelle avec l'énergie des vibrations omniprésentes dans l environnement. Cette thèse contribue à une étude générale des récupérateurs de l'énergie des vibrations (REV) employant des transducteurs électrostatiques. Un REV électrostatique typique se compose d'un transducteur capacitif, de l'électronique de conditionnement et d un élément de stockage. Ce travail se concentre sur l'examen du circuit de conditionnement auto-synchrone proposé en 2006 par le MIT, qui combine la pompe de charge à base de diodes et le convertisseur DC-DC inductif de type de flyback qui est entraîné par le commutateur. Cette architecture est très prometteuse car elle élimine la commande de grille précise des transistors utilisés dans les architectures synchrones, tandis qu'un commutateur unique se met en marche rarement. Cette thèse propose une analyse théorique du circuit de conditionnement. Nous avons développé un algorithme qui par commutation appropriée de flyback implémente la stratégie de conversion d'énergie optimale en tenant compte des pertes liées à la commutation. En ajoutant une fonction de calibration, le système devient adaptatif pour les fluctuations de l'environnement. Cette étude a été validée par la modélisation comportementale.Une autre contribution consiste en la réalisation de l'algorithme proposé au niveau du circuit CMOS. Les difficultés majeures de conception étaient liées à l'exigence de haute tension et à la priorité de la conception faible puissance. Nous avons conçu un contrôleur du commutateur haute tension de faible puissance en utilisant la technologie AMS035HV. Sa consommation varie entre quelques centaines de nanowatts et quelques microwatts, en fonction de nombreux facteurs - paramètres de vibrations externes, niveaux de tension de la pompe de charge, la fréquence de la commutation de commutateur, la fréquence de la fonction de calibration, etc.Nous avons également réalisé en silicium, fabriqué et testé un commutateur à haute tension avec une nouvelle architecture de l'élévateur de tension de faible puissance. En montant sur des composants discrets de la pompe de charge et du circuit de retour et en utilisant l'interrupteur conçu, nous avons caractérisé le fonctionnement large bande haute-tension du prototype de transducteur MEMS fabriqué à côté de cette thèse à l'ESIEE Paris. Lorsque le capteur est excité par des vibrations stochastiques ayant un niveau d'accélération de 0,8 g rms distribué dans la bande 110-170 Hz, jusqu'à 0,75 W de la puissance nette a été récupérée.Vibration energy harvesting is a relatively new concept that can be used in powering micro-scale power embedded devices with the energy of vibrations omnipresent in the surrounding. This thesis contributes to a general study of vibration energy harvesters (VEHs) employing electrostatic transducers. A typical electrostatic VEH consists of a capacitive transducer, conditioning electronics and a storage element. This work is focused on investigations of the reported by MIT in 2006 auto-synchronous conditioning circuit, which combines the diode-based charge pump and the inductive flyback energy return driven by the switch. This architecture is very promising since it eliminates precise gate control of transistors employed in synchronous architectures, while a unique switch turns on rarely. This thesis addresses the theoretical analysis of the conditioning circuit. We developed an algorithm that by proper switching of the flyback allows the optimal energy conversion strategy taking into account the losses associated with the switching. By adding the calibration function, the system became adaptive to the fluctuations in the environment. This study was validated by the behavioral modeling. Another contribution consists in realization of the proposed algorithm on the circuit level. The major design difficulties were related to the high-voltage requirement and the low-power design priority. We designed a high-voltage analog controller of the switch using AMS035HV technology. Its power consumption varies between several hundred nanowatts and a few microwatts, depending on numerous factors - parameters of external vibrations, voltage levels of the charge pump, frequency of the flyback switching, frequency of calibration function, etc. We also implemented on silicon, fabricated and tested a high-voltage switch with a novel low power level-shifting driver. By mounting on discrete components the charge pump and flyback circuit and employing the proposed switch, we characterized the wideband high-voltage operation of the MEMS transducer prototype fabricated alongside this thesis in ESIEE Paris. When excited with stochastic vibrations having an acceleration level of 0.8 g rms distributed in the band 110-170 Hz, up to 0.75 $\mu$W of net electrical power has been harvested.PARIS-JUSSIEU-Bib.électronique (751059901) / SudocSudocFranceF

Exploring the Unknown: Selected Documents in the History of the US Civilian Space Program

One of the most important developments of the twentieth century has been the movement of humanity into space with machines and people. The underpinnings of that movement -why it took the shape it did; which individuals and organizations were involved; what factors drove a particular choice of scientific objectives and technologies to be used; and the political, economic, managerial, and international contexts in which the events of the space age unfolded- are all important ingredients of this epoch transition from an earthbound to spacefaring people. This desire to understand the development of spaceflight in the United States sparked this documentary history series. 'Exploring the Unknown' is a multi-volume series containing a selection of key documents in history of the U.S. civil space program. This current volume, Volume III, focusing on the use of space for practical applications, prints 112 key documents on the history of satellite communications, remote sensing of earth, and space as an investment in economic growth, edited for ease of use. Each is introduced by a headnote providing context, bibliographical information, and background information necessary to understanding the document