Novel Microfiber Sensor and Its Biosensing Application for Detection of hCG Based on a Singlemode-Tapered Hollow Core-Singlemode Fiber Structure

A novel microfiber sensor is proposed and demonstrated based on a singlemode-tapered hollow core -singlemode (STHS) fiber structure. Experimentally a STHS with taper waist diameter of 26.5 μm has been fabricated and RI sensitivity of 816, 1601.86, and 4775.5 nm/RIU has been achieved with RI ranges from 1.3335 to 1.3395 , from 1.369 to 1.378, and from 1.409 to 1.4175 respectively, which agrees very well with simulated RI sensitivity of 885, 1517, and 4540 nm/RIU at RI ranges from 1.3335 to 1.337, from 1.37 to 1.374, and from 1.41 to 1.414 . The taper waist diameter has impact on both temperature and strain sensitivity of the sensor structure: (1) the smaller the waist diameter, the higher the temperature sensitivity, and experimentally 26.82 pm/°C has been achieved with a taper waist diameter of 21.4 μm; (2) as waist diameter decrease, strain sensitivity increase and 7.62 pm/με has been achieved with a taper diameter of 20.3 μm. The developed sensor was then functionalized for human chorionic gonadotropin (hCG) detection as an example for biosensing application. Experimentally for hCG concentration of 5 mIU/ml, the sensor has 0.5 nm wavelength shift, equivalent to limit of detection (LOD) of 0.6 mIU/ml by defining 3 times of the wavelength variation (0.06 nm) as measurement limit. The biosensor demonstrated relatively good reproducibility and specificity, which has potential for real medical diagnostics and other applications

Optical fiber sensors based on microstructured optical fibers to detect gases and volatile organic compounds-A review

Since the first publications related to microstructured optical fibers (MOFs), the development of optical fiber sensors (OFS) based on them has attracted the interest of many research groups because of the market niches that can take advantage of their specific features. Due to their unique structure based on a certain distribution of air holes, MOFs are especially useful for sensing applications: on one hand, the increased coupling of guided modes into the cladding or the holes enhances significantly the interaction with sensing films deposited there; on the other hand, MOF air holes enhance the direct interaction between the light and the analytes that get into in these cavities. Consequently, the sensitivity when detecting liquids, gasses or volatile organic compounds (VOCs) is significantly improved. This paper is focused on the reported sensors that have been developed with MOFs which are applied to detection of gases and VOCs, highlighting the advantages that this type of fiber offers.This work was carried out with the financial support of MINECO (Spain) through TEC2016-79367-C2-2-R (AEI/FEDER, UE) as well as Public University of Navarre PhD grants program.This work was carried out with the financial support of MINECO (Spain) through TEC2016-79367-C2-2-R (AEI/FEDER, UE)

Investigation of a SPR based refractive index sensor using a single mode fiber with a large D shaped microfluidic channel

In this work, a highly sensitive surface plasmon resonance (SPR) sensor based on a single mode fiber (SMF) incorporating a large microfluidic channel (MFC) for refractive index (RI) sensing is designed and optimized using a full-vectorial finite element method (FEM). The fluidic channel size can be varied according to the requirement due to the availability of the large cladding diameter of SMF, which makes it simple and easy to fabricate. The proposed novel sensor is favourable to both analytes and metallic strips. The D-shaped hollow section above the core is filled with the measurand analytes and a gold (Au) strip is deposited on the base of the MFC, as it is known as the most attractive metal for SPR. Our numerical simulations illustrate that the confinement loss of the designed sensor is highly influenced by the distance of the MFC from the core along with the width and thickness of the Au strip. The designed sensor shows an average sensitivity of 1350 nm/RIU and maximum sensitivity of 8250 nm/RIU in the sensing range of 1.33-1.35 and 1.41-1.43, respectively. However, for a small variation of na at a step of 0.005, within ranges like 1.415, 1.420, and 1.425, we have achieved a maximum sensitivity of 7000 nm/RIU, 9000 nm/RIU and 11000 nm/RIU, respectively. This novel SPR sensor with MFC can open up a new opportunity in the application of chemical and biological sensing

Magnetic Field Measurements Based on Terfenol Coated Photonic Crystal Fibers

A magnetic field sensor based on the integration of a high birefringence photonic crystal fiber and a composite material made of Terfenol particles and an epoxy resin is proposed. An in-fiber modal interferometer is assembled by evenly exciting both eigenemodes of the HiBi fiber. Changes in the cavity length as well as the effective refractive index are induced by exposing the sensor head to magnetic fields. The magnetic field sensor has a sensitivity of 0.006 (nm/mT) over a range from 0 to 300 mT with a resolution about ±1 mT. A fiber Bragg grating magnetic field sensor is also fabricated and employed to characterize the response of Terfenol composite to the magnetic field

High Sensitivity Optical Fiber Interferometric Sensors

Optical fiber interferometers have been widely employed and investigated for monitoring the changes in both physical and chemical parameters, with the advantages of compact size, light weight, immunity to electromagnetic interference, high sensitivity, capability to work in harsh environments and remote operation capabilities. Among the different kinds of fiber sensors based on interferometry, singlemode-multimode-singlemode (SMS) structures has attracted considerable interest due to their inherent advantages of high sensitivity, ease of fabrication and interconnection to other fiber systems and low cost. However, the challenge is that the sensitivity of the traditional SMS based fiber structure is not sufficient in some cases, for example in bio-chemical applications, where detection of a very small variation in a bio-chemicals’ concentration is required. There is thus a need to investigate how to modify or enhance an SMS structure to achieve ultrahigh sensitivity. This thesis presents research and its applications concerning approaches to improve the sensitivity and detection accuracy of a traditional SMS fiber structure based sensor. The key achievements of this thesis include: Traditional SMS fiber structure for breathing state monitoring A bend SMS structure is investigated as a breathing sensor by attaching it to a thin plastic film in an oxygen mask. Breath rate can be monitored using this sensor by detecting power variations due to the macro bending applied to the SMS section during each inhalation and exhalation cycles. Different types of breathing conditions including regular and irregular breath patterns can be distinguished. The proposed sensor is capable of working in a strong electromagnetic field and radioactive environment. Tapered small core singlemode fiber (SCSMF) for the detection of refractive index (RI), ammonia, and volatile organic compounds (VOCs) A modified SMS structure based on a tapered SCSMF is proposed and investigated with significantly improved RI sensitivity. It is found that the sample with a smaller waist diameter gives higher sensitivity. In the experiment, a maximum sensitivity of 19212.5 nm/RIU (RI unit) in the RI range from 1.4304 to 1.4320 has been demonstrated when the waist diameter of the SCSMF is tapered down to 12.5 μm. The best corresponding theoretical resolution of the proposed sensor is 5.025 × 10-7 RIU which is over 10 times higher than that of many previous reported optical fiber based RI sensors. The proposed structure is capable of monitoring relative humidity level change even without coating of the fiber sensor’s surface with a layer of hygroscopic material. A silica sol-gel based coating has been used as a sensitive material to ammonia for the first time, by applying it to the surface of the tapered SCSMF for the detection of ammonia in water. The proposed sensor shows an ultra-high sensitivity of 2.47 nm/ppm with short response and recovery time of less than 2 and 5 minutes respectively. The corresponding theoretical detection limit of ammonia in water is calculated to be 4 ppb, which is 3 orders of magnitude improvement compared to the previous reported interferometry based ammonia sensor. In addition, the sensor has good performance in terms of repeatability of measurement and selectivity for sensing ammonia compared to that of other common ions and organic molecules in water. VOCs sensors are also demonstrated by coating a mixture of sol-gel silica and Nile red on the surface of two different types of tapered fiber sensors (tapered SCSMF) and a microfiber coupler (MFC)). The MFC based sensor shows better sensitivities to ethanol and methanol than that based on a tapered SCSMF due to its smaller waist diameter. The detectable gas concentration changes of the MFC based sensor are calculated to be ~77 ppb and ~281 ppb for ethanol and methanol respectively which are over one order of magnitude improvement than many other reports. The sensors also show fast response times of less than 5 minutes and recovery times varied from 7 to 12 minutes. Simultaneous measurement of ethanol and methanol is achieved by utilizing two different coating recipes. Hollow core fiber (HCF) structure for high temperature and twist sensing. A modified SMS structure with much improved spectral quality factor (Q) is investigated both theoretically and experimentally. The modified structure is based on a HCF. It is found that periodic transmission dips with high spectral extinction ratio and high Q factor are excited because of the multiple beam interferences introduced by the cladding of the HCF. The HCF structure can be used as a high sensitivity (up to 33.4 pm/°C) temperature sensor in a wide working temperature range (from room temperature to 1000 °C). By coating a thin layer of silver (~ 6.7 nm) on one side of the HCF surface, a twist sensor with a maximum sensitivity of 0.717 dB/°has been achieved, which is the highest twist sensitivity reported for intensity modulation based fiber sensors, with excellent measurement repeatability. Further theoretical and experimental investigation attributes this high twist sensitivity to the polarization dependent reflection coefficient at the outer HCF surface associated with the partial silver coating

Modal Interferometers Based on a Tapered Special Photonic Crystal Fiber for Highly Sensitive Detection

The use of a tapered special photonic crystal fiber (PCF) with collapsed air holes in the waist (the thinnest part of a taper) for highly sensitive detection of strain, high temperature, and fast detection of hydrogen with concentrations between 1.2 and 5.6 vol.% and biosensing is demonstrated. In the tapered PCF, a fundamental core mode couples to a few modes of the solid taper waist. Owing to the beating between the waist modes, the transmission spectra of the tapered PCF exhibit several interference peaks, which are sensitive to refractive index changes of a medium that surrounds the taper and also to changes of a taper length. The changes can be visualized as a shift of the peaks in the output spectrum pattern

Sensores de fibra ótica para meios desafiantes

With the present work, the development of fiber optic sensor solutions for the application in challenging media was intended. New sensor structures based on the post-processing of optical fibers were addressed, taking into account their sensitivity to variations in the external environment. In a first stage, fiber Bragg gratings were embedded in lithium batteries, to monitor temperature in situ and operando. Due to the harsh chemical environment of the battery, fiber optic sensors revealed to be the most advantageous alternative, when comparing to the electronic sensors. Fiber sensors exhibited good sensitivities and fast responses, besides being less invasive, thus they did not compromise the battery response. Furthermore, they were chemically stable. Still in the framework of this theme, and with the objective of monitoring possible strain and pressure variations inside the batteries, new sensors based on in-line Fabry-Perot cavities have been proposed. These sensors were characterized in lateral load, strain, and temperature. In a later stage, the study focused on the development of configurations that allowed to obtain high-resolution and/or sensitivity sensors. One of such configurations was obtained by creating a hollow microsphere at the fiber tip. The sensor was used to detected concentration variations and refractive index of glycerin and water mixtures. The influence of the diaphragm size in the sensor response was also studied, as well as the temperature response. New sensors based on multimode interference have also been characterized, using a coreless silica fiber tip. First, the influence of different parameters, such as length and diameters were analyzed. The sensors were tested in different solutions of glucose and water. It was observed that the sensor diameter is a decisive factor in obtaining devices that are more sensitive to refractive index and, consequently, to concentration. The determination of the thermo-optic coefficient of water/ethanol mixtures was also addressed using a multimode fiber interferometer sensor. Finally, a multimode interferometer sensor was functionalized by depositing agarose throughout the structure, allowing to optimize the response of the sensors to the external environment.Com o presente trabalho pretendeu-se explorar soluções de sensores em fibra ótica para a aplicação em meios desafiantes. Novas estruturas sensoras baseadas em pós-processamento de fibra ótica foram abordadas, tendo em consideração a sua sensibilidade a variações do meio externo. Numa primeira etapa, foram embebidas redes de Bragg no interior de baterias de lítio, para monitorizar variações de temperatura in situ e operando. Devido ao complexo meio químico da bateria, os sensores em fibra ótica revelaram ser uma alternativa mais vantajosa em relação aos sensores elétricos, não só pela sensibilidade e rápida resposta, mas também pelo fato de não afetarem o desempenho da bateria. Além disso, os sensores usados revelaram ser pouco invasivos e quimicamente estáveis. Ainda no âmbito deste tema, e com o objetivo de monitorizar possíveis deformações e variações de pressão no interior da bateria de lítio, foram desenvolvidos novos sensores baseados em cavidades de Fabry-Perot do tipo in-line. Esses sensores foram caraterizados em pressão lateral, deformação e temperatura. Numa fase posterior, o estudo centrou-se no desenvolvimento de configurações que permitissem a obtenção de sensores com elevada resolução e/ou sensibilidade. Uma das configurações consistiu na formação de uma microesfera oca na ponta de uma fibra ótica. Esse sensor foi utilizado para detetar variações de concentração e índice de refração de misturas de glicerina e água. A influência do tamanho do diafragma na resposta do sensor também foi estudada, assim como a resposta em temperatura. Em seguida, desenvolveram-se novos sensores baseados em interferência multimodo, utilizando para tal uma ponta de fibra de sílica sem núcleo. Numa primeira abordagem analisou-se a influência de diferentes parâmetros, como o comprimento e o diâmetro dos sensores. Os sensores foram expostos a diferentes soluções de glucose e água. Verificou-se que o diâmetro do sensor é um fator decisivo para a obtenção de dispositivos mais sensíveis ao índice de refração e, consequentemente, à concentração. Foi também desenvolvido um sensor baseado em interferência multimodo que permitiu determinar o coeficiente termo-ótico de misturas de etanol e água. Por fim, procedeu-se à funcionalização de um sensor baseado em interferência multimodo através da deposição de agarose ao longo da estrutura, permitindo assim otimizar a sua resposta a variações do meio externo.Programa Doutoral em Engenharia Físic

Optical fiber sensors for in-situ detection of solid-liquid phase change for n-octadecane

In the past few decades solid-liquid phase change materials (PCMs) have gained an increasingly important role in thermal energy storage applications due to their ability to absorb or release large amounts of energy during melting or solidification. The precise phase change temperature varies with different conditions, such as external pressure, small variations in the PCM composition in the case of multi-component mixtures and/or material purity. In order to achieve better energy efficiency for the energy storage process, it is necessary to be able to accurately detect the solid-liquid phase changes in the bulk of a PCM. Optical fiber sensors allow for direct detection of the phase changes in PCMs while also offering the advantages of a passive nature and small size. The focus of the research presented in this thesis is on the development of a novel approach to detecting the solid-liquid phase changes in selected PCMs using optical fiber sensors. To achieve this goal, initially the correlation between the temperature, changes in the refractive index (RI) and internal pressure acting upon the optical fiber during the phase transitions was studied for the selected PCM, n-octadecane. Based on the results of these studies, several optical fiber sensing structures have been proposed and demonstrated for the detection of phase changes as follows: An optical fiber Fresnel reflection sensor for detection of phase changes. An fiber Fresnel reflection sensor for detection of solid-liquid phase change in n-octadecane is proposed and experimentally demonstrated. The sensor probe consists of a single-mode fiber with a cleaved end immersed in the n-octadecane sample under test. The detection relies on measuring the slope of the output power ratio change which is caused by the RI change during the phase transition. The results of this work suggest that such a simple optical fiber sensor can be used for detection of liquid-solid phase changes in other materials with similar thermo-optic properties to n-octadecane. This sensor realized in-situ detection for a solid liquid phase change, which is a significant advantage compared to the traditional phase change detection methods. A fiber heterostructure based optical fiber sensor for detection of phase changes. A single-mode-no-core-single-mode fiber optical sensor for the detection of solid-liquid and liquid-solid phase changes in n-octadecane is proposed and demonstrated. The transmission-type sensor probe consists of a short section of no-core fiber sandwiched between two sections of a single-mode fiber. The detection relies on measuring the level of the output power ratio which is caused by the large step-like variations in the RI of n-octadecane’s. Importantly, compared to the Fresnel reflection sensor, the proposed fiber heterostructure is resistant to bending and strain disturbances during the measurements. The results of this work suggest that the proposed sensor is potentially capable of detecting liquid-solid phase changes in other materials whose thermo-optic properties are similar to those of n-octadecane. Moreover, this sensor not only has the advantage of achieving in-situ phase change detection, but also has the ability of working in an environment subjected to mechanical disturbance, which makes it has great potential of industry applications. Optical fiber Fabry-Perot sensor based on a singlemode-hollow core-singlemode fiber. An optical fiber Fabry-Perot sensor to monitor the solid-liquid and liquid-solid phase changes in n-octadecane is also proposed and investigated. The sensor probe is fabricated by splicing a short section of a hollow core fiber between two single-mode fibers. By analyzing the changes in the output spectrum of the probe, such as spectral shift of a selected interference dip, the phase change within a material sample in the vicinity of the fiber probe can be accurately detected. The proposed sensor can deal with PCM types whose RI values make it difficult for the other two sensor types to work, and also can be used for detection of the material’s phase state at a particular point of its volume. This work has the potential to better understanding phase change mechanism and its application in energy engineering. Compared to the other sensors developed in the research presented in this thesis, this sensor has the advantage that the application is not limited by the RI of the PCMs

MINIATURIZED FIBER MODAL INTERFEROMETERS AND THEIR APPLICATIONS AS FIBER SENSORS

Ph.DDOCTOR OF PHILOSOPH