Adaptation in Standard CMOS Processes with Floating Gate Structures and Techniques

We apply adaptation into ordinary circuits and systems to achieve high performance, high quality results. Mismatch in manufactured VLSI devices has been the main limiting factor in quality for many analog and mixed-signal designs. Traditional compensation methods are generally costly. A few examples include enlarging the device size, averaging signals, and trimming with laser. By applying floating gate adaptation to standard CMOS circuits, we demonstrate here that we are able to trim CMOS comparator offset to a precision of 0.7mV, reduce CMOS image sensor fixed-pattern noise power by a factor of 100, and achieve 5.8 effective number of bits (ENOB) in a 6-bit flash analog-to-digital converter (ADC) operating at 750MHz. The adaptive circuits generally exhibit special features in addition to an improved performance. These special features are generally beyond the capabilities of traditional CMOS design approaches and they open exciting opportunities in novel circuit designs. Specifically, the adaptive comparator has the ability to store an accurate arbitrary offset, the image sensor can be set up to memorize previously captured scenes like a human retina, and the ADC can be configured to adapt to the incoming analog signal distribution and perform an efficient signal conversion that minimizes distortion and maximizes output entropy

A Low-Power, Reconfigurable, Pipelined ADC with Automatic Adaptation for Implantable Bioimpedance Applications

Biomedical monitoring systems that observe various physiological parameters or electrochemical reactions typically cannot expect signals with fixed amplitude or frequency as signal properties can vary greatly even among similar biosignals. Furthermore, advancements in biomedical research have resulted in more elaborate biosignal monitoring schemes which allow the continuous acquisition of important patient information. Conventional ADCs with a fixed resolution and sampling rate are not able to adapt to signals with a wide range of variation. As a result, reconfigurable analog-to-digital converters (ADC) have become increasingly more attractive for implantable biosensor systems. These converters are able to change their operable resolution, sampling rate, or both in order convert changing signals with increased power efficiency. Traditionally, biomedical sensing applications were limited to low frequencies. Therefore, much of the research on ADCs for biomedical applications focused on minimizing power consumption with smaller bias currents resulting in low sampling rates. However, recently bioimpedance monitoring has become more popular because of its healthcare possibilities. Bioimpedance monitoring involves injecting an AC current into a biosample and measuring the corresponding voltage drop. The frequency of the injected current greatly affects the amplitude and phase of the voltage drop as biological tissue is comprised of resistive and capacitive elements. For this reason, a full spectrum of measurements from 100 Hz to 10-100 MHz is required to gain a full understanding of the impedance. For this type of implantable biomedical application, the typical low power, low sampling rate analog-to-digital converter is insufficient. A different optimization of power and performance must be achieved. Since SAR ADC power consumption scales heavily with sampling rate, the converters that sample fast enough to be attractive for bioimpedance monitoring do not have a figure-of-merit that is comparable to the slower converters. Therefore, an auto-adapting, reconfigurable pipelined analog-to-digital converter is proposed. The converter can operate with either 8 or 10 bits of resolution and with a sampling rate of 0.1 or 20 MS/s. Additionally, the resolution and sampling rate are automatically determined by the converter itself based on the input signal. This way, power efficiency is increased for input signals of varying frequency and amplitude

Large scale reconfigurable analog system design enabled through floating-gate transistors

This work is concerned with the implementation and implication of non-volatile charge storage on VLSI system design. To that end, the floating-gate pFET (fg-pFET) is considered in the context of large-scale arrays. The programming of the element in an efficient and predictable way is essential to the implementation of these systems, and is thus explored. The overhead of the control circuitry for the fg-pFET, a key scalability issue, is examined. A light-weight, trend-accurate model is absolutely necessary for VLSI system design and simulation, and is also provided. Finally, several reconfigurable and reprogrammable systems that were built are discussed.Ph.D.Committee Chair: Hasler, Paul E.; Committee Member: Anderson, David V.; Committee Member: Ayazi, Farrokh; Committee Member: Degertekin, F. Levent; Committee Member: Hunt, William D

Accelerated hardware video object segmentation: From foreground detection to connected components labelling

This is the preprint version of the Article - Copyright @ 2010 ElsevierThis paper demonstrates the use of a single-chip FPGA for the segmentation of moving objects in a video sequence. The system maintains highly accurate background models, and integrates the detection of foreground pixels with the labelling of objects using a connected components algorithm. The background models are based on 24-bit RGB values and 8-bit gray scale intensity values. A multimodal background differencing algorithm is presented, using a single FPGA chip and four blocks of RAM. The real-time connected component labelling algorithm, also designed for FPGA implementation, run-length encodes the output of the background subtraction, and performs connected component analysis on this representation. The run-length encoding, together with other parts of the algorithm, is performed in parallel; sequential operations are minimized as the number of run-lengths are typically less than the number of pixels. The two algorithms are pipelined together for maximum efficiency

An Analog VLSI Deep Machine Learning Implementation

Machine learning systems provide automated data processing and see a wide range of applications. Direct processing of raw high-dimensional data such as images and video by machine learning systems is impractical both due to prohibitive power consumption and the “curse of dimensionality,” which makes learning tasks exponentially more difficult as dimension increases. Deep machine learning (DML) mimics the hierarchical presentation of information in the human brain to achieve robust automated feature extraction, reducing the dimension of such data. However, the computational complexity of DML systems limits large-scale implementations in standard digital computers. Custom analog signal processing (ASP) can yield much higher energy efficiency than digital signal processing (DSP), presenting means of overcoming these limitations. The purpose of this work is to develop an analog implementation of DML system. First, an analog memory is proposed as an essential component of the learning systems. It uses the charge trapped on the floating gate to store analog value in a non-volatile way. The memory is compatible with standard digital CMOS process and allows random-accessible bi-directional updates without the need for on-chip charge pump or high voltage switch. Second, architecture and circuits are developed to realize an online k-means clustering algorithm in analog signal processing. It achieves automatic recognition of underlying data pattern and online extraction of data statistical parameters. This unsupervised learning system constitutes the computation node in the deep machine learning hierarchy. Third, a 3-layer, 7-node analog deep machine learning engine is designed featuring online unsupervised trainability and non-volatile floating-gate analog storage. It utilizes massively parallel reconfigurable current-mode analog architecture to realize efficient computation. And algorithm-level feedback is leveraged to provide robustness to circuit imperfections in analog signal processing. At a processing speed of 8300 input vectors per second, it achieves 1×1012 operation per second per Watt of peak energy efficiency. In addition, an ultra-low-power tunable bump circuit is presented to provide similarity measures in analog signal processing. It incorporates a novel wide-input-range tunable pseudo-differential transconductor. The circuit demonstrates tunability of bump center, width and height with a power consumption significantly lower than previous works

Development of single-cell protectors for sealed silver-zinc cells

Three design approaches to cell-level protection were developed, fabricated, and tested. These systems are referred to as the single-cell protector (SCP), multiplexed-cell protector(MCP). To evaluate the systems 18-cell battery packs without cell level control were subjected to cycle life test. A total of five batteries were subjected to simulate synchronous orbit cycling at 40% depth of discharge at 22C. Batteries without cell-level protection failed between 345 and 255 cycles. Cell failure in the cell level protected batteries occurred between 412 and 540. It was determined that the cell-level monitoring and protection is necessary to attain the long cycle life of a AgZn battery. The best method of providing control and protection of the AgZn cells depends on the specific application and capability of the user

Propuesta de arquitectura y circuitos para la mejora del rango dinámico de sistemas de visión en un chip diseñados en tecnologías CMOS profundamente submicrométrica

El trabajo presentado en esta tesis trata de proponer nuevas técnicas para la expansión del rango dinámico en sensores electrónicos de imagen. En este caso, hemos dirigido nuestros estudios hacia la posibilidad de proveer dicha funcionalidad en un solo chip. Esto es, sin necesitar ningún soporte externo de hardware o software, formando un tipo de sistema denominado Sistema de Visión en un Chip (VSoC). El rango dinámico de los sensores electrónicos de imagen se define como el cociente entre la máxima y la mínima iluminación medible. Para mejorar este factor surgen dos opciones. La primera, reducir la mínima luz medible mediante la disminución del ruido en el sensor de imagen. La segunda, incrementar la máxima luz medible mediante la extensión del límite de saturación del sensor. Cronológicamente, nuestra primera opción para mejorar el rango dinámico se basó en reducir el ruido. Varias opciones se pueden tomar para mejorar la figura de mérito de ruido del sistema: reducir el ruido usando una tecnología CIS o usar circuitos dedicados, tales como calibración o auto cero. Sin embargo, el uso de técnicas de circuitos implica limitaciones, las cuales sólo pueden ser resueltas mediante el uso de tecnologías no estándar que están especialmente diseñadas para este propósito. La tecnología CIS utilizada está dirigida a la mejora de la calidad y las posibilidades del proceso de fotosensado, tales como sensibilidad, ruido, permitir imagen a color, etcétera. Para estudiar las características de la tecnología en más detalle, se diseñó un chip de test, lo cual permite extraer las mejores opciones para futuros píxeles. No obstante, a pesar de un satisfactorio comportamiento general, las medidas referentes al rango dinámico indicaron que la mejora de este mediante sólo tecnología CIS es muy limitada. Es decir, la mejora de la corriente oscura del sensor no es suficiente para nuestro propósito. Para una mayor mejora del rango dinámico se deben incluir circuitos dentro del píxel. No obstante, las tecnologías CIS usualmente no permiten nada más que transistores NMOS al lado del fotosensor, lo cual implica una seria restricción en el circuito a usar. Como resultado, el diseño de un sensor de imagen con mejora del rango dinámico en tecnologías CIS fue desestimado en favor del uso de una tecnología estándar, la cual da más flexibilidad al diseño del píxel. En tecnologías estándar, es posible introducir una alta funcionalidad usando circuitos dentro del píxel, lo cual permite técnicas avanzadas para extender el límite de saturación de los sensores de imagen. Para este objetivo surgen dos opciones: adquisición lineal o compresiva. Si se realiza una adquisición lineal, se generarán una gran cantidad de datos por cada píxel. Como ejemplo, si el rango dinámico de la escena es de 120dB al menos se necesitarían 20-bits/píxel, log2(10120/20)=19.93, para la representación binaria de este rango dinámico. Esto necesitaría de amplios recursos para procesar esta gran cantidad de datos, y un gran ancho de banda para moverlos al circuito de procesamiento. Para evitar estos problemas, los sensores de imagen de alto rango dinámico usualmente optan por utilizar una adquisición compresiva de la luz. Por lo tanto, esto implica dos tareas a realizar: la captura y la compresión de la imagen. La captura de la imagen se realiza a nivel de píxel, en el dispositivo fotosensor, mientras que la compresión de la imagen puede ser realizada a nivel de píxel, de sistema, o mediante postprocesado externo. Usando el postprocesado, existe un campo de investigación que estudia la compresión de escenas de alto rango dinámico mientras se mantienen los detalles, produciendo un resultado apropiado para la percepción humana en monitores convencionales de bajo rango dinámico. Esto se denomina Mapeo de Tonos (Tone Mapping) y usualmente emplea solo 8-bits/píxel para las representaciones de imágenes, ya que éste es el estándar para las imágenes de bajo rango dinámico. Los píxeles de adquisición compresiva, por su parte, realizan una compresión que no es dependiente de la escena de alto rango dinámico a capturar, lo cual implica una baja compresión o pérdida de detalles y contraste. Para evitar estas desventajas, en este trabajo, se presenta un píxel de adquisición compresiva que aplica una técnica de mapeo de tonos que permite la captura de imágenes ya comprimidas de una forma optimizada para mantener los detalles y el contraste, produciendo una cantidad muy reducida de datos. Las técnicas de mapeo de tonos ejecutan normalmente postprocesamiento mediante software en un ordenador sobre imágenes capturadas sin compresión, las cuales contienen una gran cantidad de datos. Estas técnicas han pertenecido tradicionalmente al campo de los gráficos por ordenador debido a la gran cantidad de esfuerzo computacional que requieren. Sin embargo, hemos desarrollado un nuevo algoritmo de mapeo de tonos especialmente adaptado para aprovechar los circuitos dentro del píxel y que requiere un reducido esfuerzo de computación fuera de la matriz de píxeles, lo cual permite el desarrollo de un sistema de visión en un solo chip. El nuevo algoritmo de mapeo de tonos, el cual es un concepto matemático que puede ser simulado mediante software, se ha implementado también en un chip. Sin embargo, para esta implementación hardware en un chip son necesarias algunas adaptaciones y técnicas avanzadas de diseño, que constituyen en sí mismas otra de las contribuciones de este trabajo. Más aún, debido a la nueva funcionalidad, se han desarrollado modificaciones de los típicos métodos a usar para la caracterización y captura de imágenes

Low-Power and Programmable Analog Circuitry for Wireless Sensors

Embedding networks of secure, wirelessly-connected sensors and actuators will help us to conscientiously manage our local and extended environments. One major challenge for this vision is to create networks of wireless sensor devices that provide maximal knowledge of their environment while using only the energy that is available within that environment. In this work, it is argued that the energy constraints in wireless sensor design are best addressed by incorporating analog signal processors. The low power-consumption of an analog signal processor allows persistent monitoring of multiple sensors while the device\u27s analog-to-digital converter, microcontroller, and transceiver are all in sleep mode. This dissertation describes the development of analog signal processing integrated circuits for wireless sensor networks. Specific technology problems that are addressed include reconfigurable processing architectures for low-power sensing applications, as well as the development of reprogrammable biasing for analog circuits

Low-Power and Programmable Analog Circuitry for Wireless Sensors

Embedding networks of secure, wirelessly-connected sensors and actuators will help us to conscientiously manage our local and extended environments. One major challenge for this vision is to create networks of wireless sensor devices that provide maximal knowledge of their environment while using only the energy that is available within that environment. In this work, it is argued that the energy constraints in wireless sensor design are best addressed by incorporating analog signal processors. The low power-consumption of an analog signal processor allows persistent monitoring of multiple sensors while the device\u27s analog-to-digital converter, microcontroller, and transceiver are all in sleep mode. This dissertation describes the development of analog signal processing integrated circuits for wireless sensor networks. Specific technology problems that are addressed include reconfigurable processing architectures for low-power sensing applications, as well as the development of reprogrammable biasing for analog circuits