차량용 CIS Interface 를 위한 All-Digital Phase-Locked Loop 의 설계 및 분석

학위논문 (석사) -- 서울대학교 대학원 : 공과대학 전기·정보공학부, 2021. 2. 정덕균.This thesis presents design techniques for All-Digital Phase-Locked Loop (ADPLL) assisting the automotive CMOS image sensor (CIS) interface. To target Gear 3 of the automotive physical system, the proposed AD-PLL has a wide operation range, low RMS jitter, and high PVT tolerance characteristics. Detailed analysis of the loop dynamics and the noise analysis of AD-PLL are done by using Matlab and Verilog behavioral modeling simulation before an actual design. Based on that analysis, the optimal DLF gain configurations are yielded, and also, accurate output responses and performance are predictable. The design techniques to reduce the output RMS jitter are discussed thoroughly and utilized for actual implementation. The proposed AD-PLL is fabricated in the 40 nm CMOS process and occupies an effective area of 0.026 mm2. The PLL output clock pulses exhibit an RMS jitter of 827 fs at 2 GHz. The power dissipation is 5.8 mW at 2 GHz, where the overall supply voltage domain is 0.9 V excluding the buffer which is 1.1 V domain.본 논문에서는 자동차 CMOS 이미지 센서 (CIS) 인터페이스를 지원하 는 AD-PLL 을 제안한다. Automotive Physical 시스템의 Gear 3 를 지원하기 위해 제안된 AD-PLL 은 1.5 GHz 에서 3 GHz 의 동작 주파수를 가지며, 낮 은 RMS Jitter 및 PVT 변화에 대한 높은 둔감성을 갖는다. 설계에 앞서서 Matlab 및 Verilog Behavioral Simulation 을 통해 Loop system 의 역학에 대한 자세한 분석 및 AD-PLL 의 Noise 분석을 수행하였고, 이 분석을 기반으로 최적의 DLF gain 과 정확한 출력 응답 및 성능을 예측 할 수 있었다. 또한, 출력의 Phase Noise 와 RMS Jitter 를 줄이기 위한 설계 기법을 자세히 다루고 있으며 이를 실제 구현에 활용했다. 제안된 회로는 40 nm CMOS 공정으로 제작되었으며 Decoupling Cap 을 제외하고 0.026 mm2 의 유효 면적을 차지한다. 측정된 출력 Clock 신호의 RMS Jitter 값은 2 GHz 에서 827 fs 이며, 총 5.8 mW의 Power 를 소비한다. 이 때, 전체적인 공급 전압은 0.9 V 이며, Buffer 의 Power 만이 1.1 V 를 사용하 였다.ABSTRACT I CONTENTS II LIST OF FIGURES IV LIST OF TABLES VII CHAPTER 1 INTRODUCTION 1 1.1 MOTIVATION 1 1.2 THESIS ORGANIZATION 3 CHAPTER 2 BACKGROUND ON ALL-DIGITAL PLL 4 2.1 OVERVIEW 4 2.2 BUILDING BLOCKS OF AD-PLL 7 2.2.1 TIME-TO-DIGITAL CONVERTER 7 2.2.2 DIGITALLY-CONTROLLED OSCILLATOR 10 2.2.3 DIGITAL LOOP FILTER 13 2.2.4 DELTA-SIGMA MODULATOR 16 2.3 PHASE NOISE ANALYSIS OF AD-PLL 20 2.3.1 BASIC ASSUMPTION OF LINEAR ANALYSIS 20 2.3.2 NOISE SOURCES OF AD-PLL 21 2.3.3 EFFECTS OF LOOP DELAY ON AD-PLL 24 2.3.4 PHASE NOISE ANALYSIS OF PROPOSED AD-PLL 26 CHAPTER 3 DESIGN OF ALL-DIGITAL PLL 28 3.1 DESIGN CONSIDERATION 28 3.2 OVERALL ARCHITECTURE 30 3.3 CIRCUIT IMPLEMENTATION 32 3.3.1 PFD-TDC 32 3.3.2 DCO 37 3.3.3 DIGITAL BLOCK 43 3.3.4 LEVEL SHIFTING BUFFER AND DIVIDER 45 CHAPTER 4 MEASUREMENT AND SIMULATION RESULTS 52 4.1 DIE PHOTOMICROGRAPH 52 4.2 MEASUREMENT SETUP 54 4.3 TRANSIENT ANALYSIS 57 4.4 PHASE NOISE AND SPUR PERFORMANCE 59 4.4.1 FREE-RUNNING DCO 59 4.4.2 PLL PERFORMANCE 61 4.5 PERFORMANCE SUMMARY 65 CHAPTER 5 CONCLUSION 67 BIBLIOGRAPHY 68 초 록 72Maste

Digital controlled oscillator (DCO) for all digital phase-locked loop (ADPLL) – a review

Digital controlled oscillator (DCO) is becoming an attractive replacement over the voltage control oscillator (VCO) with the advances of digital intensive research on all-digital phase locked-loop (ADPLL) in complementary metal-oxide semiconductor (CMOS) process technology. This paper presents a review of various CMOS DCO schemes implemented in ADPLL and relationship between the DCO parameters with ADPLL performance. The DCO architecture evaluated through its power consumption, speed, chip area, frequency range, supply voltage, portability and resolution. It can be concluded that even though there are various schemes of DCO that have been implemented for ADPLL, the selection of the DCO is frequently based on the ADPLL applications and the complexity of the scheme. The demand for the low power dissipation and high resolution DCO in CMOS technology shall remain a challenging and active area of research for years to come. Thus, this review shall work as a guideline for the researchers who wish to work on all digital PLL

올 디지털 클럭 및 데이터 복원 회로를 적용한 고속 광 수신기 설계

학위논문 (박사)-- 서울대학교 대학원 : 전기·컴퓨터공학부, 2016. 8. 정덕균.This thesis presents a 22- to 26.5-Gb/s optical receiver with an all-digital clock and data recovery (ADCDR) fabricated in a 65-nm CMOS process. The receiver consists of an optical front-end and a half-rate bang-bang clock and data recovery circuit. The optical front-end achieves low power consumption by using inverter-based amplifiers and realizes sufficient bandwidth by applying several bandwidth extension techniques. In addition, in order to minimize additional jitter at the front-end, not only magnitude and bandwidth but also phase delay responses are considered. The ADCDR employs an LC quadrature digitally-controlled oscillator (LC-QDCO) to achieve a high phase noise figure-of-merit at tens of gigahertz. The recovered clock jitter is 1.28 psrms and the measured jitter tolerance exceeds the tolerance mask specified in IEEE 802.3ba. The receiver sensitivity is 106 and 184 μApk-pk for a bit error rate of 10−12 at data rates of 25 and 26.5 Gb/s, respectively. The entire receiver chip occupies an active die area of 0.75 mm2 and consumes 254 mW at a data rate of 26.5 Gb/s. The energy efficiencies of the front-end and entire receiver at 26.5 Gb/s are 1.35 and 9.58 pJ/bit, respectively.CHAPTER 1 INTRODUCTION 1 1.1 MOTIVATION 1 1.2 THESIS ORGANIZATION 5 CHAPTER 2 DESIGN OF OPTICAL FRONT-END 7 2.1 OVERVIEW 7 2.2 BACKGROUND ON OPTICAL FRONT-END 9 2.2.1 PHOTODIODE 9 2.2.2 TRANSIMPEDANCE AMPLIFIER 11 2.2.3 POST AMPLIFIER 17 2.2.4 SHUNT INDUCTIVE PEAKING 25 2.3 CIRCUIT IMPLEMENTATION 29 2.3.1 OVERALL ARCHITECTURE 29 2.3.2 TRANSIMPEDANCE AMPLIFIER 31 2.3.3 POST AMPLIFIER 34 2.4 NOISE ANALYSIS 43 2.4.1 PHOTODIODE 43 2.4.2 OPTICAL FRONT-END 44 2.4.3 SENSITIVITY 46 CHAPTER 3 DESIGN OF ADCDR FOR OPTICAL RECEIVER 48 3.1 OVERVIEW 48 3.2 BACKGROUND ON PLL-BASED ADCDR 51 3.2.1 PHASE DETECTOR 51 3.2.2 DIGITAL LOOP FILTER 54 3.2.3 DIGITALLY-CONTROLLED OSCILLATOR 56 3.2.4 ANALYSIS OF BANG-BANG ADCDR 67 3.3 CIRCUIT IMPLEMENTATION 70 3.3.1 OVERALL ARCHITECTURE 70 3.3.2 PHASE DETECTION LOGIC 75 3.3.3 DIGITAL LOOP FILTER 77 3.3.4 LC QUADRATURE DCO 78 CHAPTER 4 EXPERIMENTAL RESULTS 82 CHAPTER 5 CONCLUSION 90 BIBLIOGRAPHY 92 초록 101Docto

통계적 주파수 검출기 기반 기준 주파수를 사용하지 않는 클록 및 데이터 복원 회로의 설계 방법론

학위논문(박사) -- 서울대학교대학원 : 공과대학 전기·정보공학부, 2022. 8. 정덕균.In this thesis, a design of a high-speed, power-efficient, wide-range clock and data recovery (CDR) without a reference clock is proposed. A frequency acquisition scheme using a stochastic frequency detector (SFD) based on the Alexander phase detector (PD) is utilized for the referenceless operation. Pat-tern histogram analysis is presented to analyze the frequency acquisition behavior of the SFD and verified by simulation. Based on the information obtained by pattern histogram analysis, SFD using autocovariance is proposed. With a direct-proportional path and a digital integral path, the proposed referenceless CDR achieves frequency lock at all measurable conditions, and the measured frequency acquisition time is within 7μs. The prototype chip has been fabricated in a 40-nm CMOS process and occupies an active area of 0.032 mm2. The proposed referenceless CDR achieves the BER of less than 10-12 at 32 Gb/s and exhibits an energy efficiency of 1.15 pJ/b at 32 Gb/s with a 1.0 V supply.본 논문은 기준 클럭이 없는 고속, 저전력, 광대역으로 동작하는 클럭 및 데이터 복원회로의 설계를 제안한다. 기준 클럭이 없는 동작을 위해서 알렉산더 위상 검출기에 기반한 통계적 주파수 검출기를 사용하는 주파수 획득 방식이 사용된다. 통계적 주파수 검출기의 주파수 추적 양상을 분석하기 위해 패턴 히스토그램 분석 방법론을 제시하였고 시뮬레이션을 통해 검증하였다. 패턴 히스토그램 분석을 통해 얻은 정보를 바탕으로 자기공분산을 이용한 통계적 주파수 검출기를 제안한다. 직접 비례 경로와 디지털 적분 경로를 통해 제안된 기준 클럭이 없는 클럭 및 데이터 복원회로는 모든 측정 가능한 조건에서 주파수 잠금을 달성하는 데 성공하였고, 모든 경우에서 측정된 주파수 추적 시간은 7μs 이내이다. 40-nm CMOS 공정을 이용하여 만들어진 칩은 0.032 mm2의 면적을 차지한다. 제안하는 클럭 및 데이터 복원회로는 32 Gb/s의 속도에서 비트에러율 10-12 이하로 동작하였고, 에너지 효율은 32Gb/s의 속도에서 1.0V 공급전압을 사용하여 1.15 pJ/b을 달성하였다.CHAPTER 1 INTRODUCTION 1 1.1 MOTIVATION 1 1.2 THESIS ORGANIZATION 13 CHAPTER 2 BACKGROUNDS 14 2.1 CLOCKING ARCHITECTURES IN SERIAL LINK INTERFACE 14 2.2 GENERAL CONSIDERATIONS FOR CLOCK AND DATA RECOVERY 24 2.2.1 OVERVIEW 24 2.2.2 JITTER 26 2.2.3 CDR JITTER CHARACTERISTICS 33 2.3 CDR ARCHITECTURES 39 2.3.1 PLL-BASED CDR – WITH EXTERNAL REFERENCE CLOCK 39 2.3.2 DLL/PI-BASED CDR 44 2.3.3 PLL-BASED CDR – WITHOUT EXTERNAL REFERENCE CLOCK 47 2.4 FREQUENCY ACQUISITION SCHEME 50 2.4.1 TYPICAL FREQUENCY DETECTORS 50 2.4.1.1 DIGITAL QUADRICORRELATOR FREQUENCY DETECTOR 50 2.4.1.2 ROTATIONAL FREQUENCY DETECTOR 54 2.4.2 PRIOR WORKS 56 CHAPTER 3 DESIGN OF THE REFERENCELESS CDR USING SFD 58 3.1 OVERVIEW 58 3.2 PROPOSED FREQUENCY DETECTOR 62 3.2.1 MOTIVATION 62 3.2.2 PATTERN HISTOGRAM ANALYSIS 68 3.2.3 INTRODUCTION OF AUTOCOVARIANCE TO STOCHASTIC FREQUENCY DETECTOR 75 3.3 CIRCUIT IMPLEMENTATION 83 3.3.1 IMPLEMENTATION OF THE PROPOSED REFERENCELESS CDR 83 3.3.2 CONTINUOUS-TIME LINEAR EQUALIZER (CTLE) 85 3.3.3 DIGITALLY-CONTROLLED OSCILLATOR (DCO) 87 3.4 MEASUREMENT RESULTS 89 CHAPTER 4 CONCLUSION 99 APPENDIX A DETAILED FREQUENCY ACQUISITION WAVEFORMS OF THE PROPOSED SFD 100 BIBLIOGRAPHY 108 초 록 122박

Clock multiplication techniques for high-speed I/Os

Generation of a low-jitter, high-frequency clock from a low-frequency reference clock using classical analog phase-locked loops (PLLs) requires a large loop filter capacitor and power hungry oscillator. Digital PLLs can help reduce area but their jitter performance is severely degraded by quantization error. In this dissertation different clock multiplication techniques have been explored that can be suitable for high-speed wireline systems. With the emphasis on ring oscillator based architecture using cascaded stages, three possible architectures are explored. First, a scrambling TDC (STDC) is presented to improve deterministic jitter (DJ) performance when used with a low-frequency reference clock. A cascaded architecture with digital multiplying delay locked loop as the first stage and hybrid analog/digital PLL as the second stage is used to achieve low random jitter in a power efficient manner. Fabricated in a 90nm CMOS process, the prototype frequency synthesizer consumes 4.76mW power from a 1.0V supply and generates 160MHz and 2.56 GHz output clocks from a 1.25MHz crystal reference frequency. The long-term absolute jitter of the 60MHz digital MDLL and 2.56 GHz digital PLL outputs are 2.4 psrms and 4.18 psrms, while the peak-to-peak jitter is 22.1 ps and 35.2 ps, respectively. The proposed frequency synthesizer occupies an active die area of 0.16mm2 and achieves power efficiency of 1.86 mW/GHz. Second, a hybrid phase/current-mode phase interpolator (HPC-PI) is presented to improve phase noise performance of ring oscillator-based fractional-N PLLs. The proposed HPC-PI alleviates the bandwidth trade-off between VCO phase noise suppression and ΔΣ quantization noise suppression. By combining the phase detection and interpolation functions into an XOR phase detector/interpolator (XOR PD-PI) block, accurate quantization error cancellation is achieved without using calibration. Use of a digital MDLL in front of the fractional-N PLL helps in alleviating the bandwidth limitation due to reference frequency and enables bandwidth extension even further. The extended bandwidth helps in suppressing the ring-VCO phase noise and lowering the in-band noise floor. Fabricated in 65nm CMOS process, the prototype generates fractional frequencies from 4.25 to 4.75 GHz, with an in-band phase noise floor of -104 dBc/Hz and 1.5 psrms integrated jitter. The clock multiplier achieves power efficiency of 2.4mW/GHz and FoM of -225.8 dB. Finally, an efficient clock generation, recovery, and distribution techniques for flexible-rate transceivers are presented. Using a fixed-frequency low-jitter clock provided by an integer-N PLL, fractional frequencies are generated/recovered locally using multi-phase fractional clock multipliers. Fabricated in a 65nm CMOS, the prototype transceiver can be programmed to operate at any rate from 3-to-10 Gb/s. At 10 Gb/s, integrated jitter of the Tx output and recovered clock is 360 fsrms and 758 fsrms, respectively

비디오 클럭 주파수 보상 구조를 이용한 디스플레이포트 수신단 설계

학위논문 (박사)-- 서울대학교 대학원 : 전기·컴퓨터공학부, 2014. 8. 정덕균.This thesis presents the design of DisplayPort receiver which is a high speed digital display interface replacing existing interfaces such as DVI, HDMI, LVDS and so on. The two prototype chips are fabricated, one is a 5.4/2.7/1.62-Gb/s multi-rate DisplayPort receiver and the other is a 2.7/1.62-Gb/s multi-rate Embedded DisplayPort (eDP) receiver for an intra-panel display interface. The first receiver which is designed to support the external box-to-box display connection provides up to 4K resolution (4096×2160) with the maximum data rate of 21.6 Gb/s when 4 lanes are all used. The second one aims to connect internal chip-to-chip connection such as graphic processors to display panels in notebooks or tablet PCs. It supports the maximum data rate of 10.8 Gb/s with 4-lane operation which is able to provide the resolution of WQXGA (2560×1600). Since there is no dedicated clock channel, it must contain clock and data recovery (CDR) circuit to extract the link clock from the data stream. All-Digital CDR (ADCDR) is adopted for area efficiency and better performances of the multi-rate operation. The link rate is fixed but the video clock frequency range is fairly wide for supporting all display resolutions and frame rates. Thus, the wide range video clock frequency synthesizer is essential for reconstructing the transmitted video data. A source device starts link training before transmitting video data to recover the clock and establish the link. When the loss of synchronization between the source device and the sink device happens, it usually restarts the link training and try to re-establish the link. Since link training spends several milliseconds for initializing, the video image is not displayed properly in the sink device during this interval. The proposed clock recovery scheme can significantly shorten the time to recover from the link failure with the ADCDR topology. Once the link is established after link training, the ADCDR memorizes the DCO codes of the synchronization state and when the loss of synchronization happens, it restores the previous DCO code so that the clock is quickly recovered from the failure state without the link re-training. The direct all-digital frequency synthesizer is proposed to generate the cycle-accurate video clock frequency. The video clock frequency has wide range to cover all display formats and is determined by the division ratio of large M and N values. The proposed frequency synthesizer using a programmable integer divider and a multi-phase switching fractional divider with the delta-sigma modulation exhibits better performances and reduces the design complexity operating with the existing clock from the ADCDR circuit. In asynchronous clock system, the transmitted M value which changes over time is measured by using a counter running with the long reference period (N cycles) and updated once per blank period. Thus, the transmitted M is not accurate due to its low update rate, transport latency and quantization error. The proposed frequency error compensation scheme resolves these problems by monitoring the status of FIFO between the clock domains. The first prototype chip is fabricated in a 65-nm CMOS process and the physical layer occupies 1.39 mm2 and the estimated area of the link layer is 2.26 mm2. The physical layer dissipates 86/101/116 mW at 1.62/2.7/5.4 Gb/s data rate with all 4-lane operation. The power consumption of the link layer is 107/145/167 mW at 1.62/2.7/5.4 Gb/s. The second prototype chip, fabricated in a 0.13μm CMOS process, presents the physical layer area of 1.59 mm2 and the link layer area of 3.01 mm2. The physical layer dissipates 21 mW at 1.62 Gb/s and 29 mW at 2.7 Gb/s with 2-lane operation. The power consumption of the link layer is 31 mW at 1.62 Gb/s and 41 mW at 2.7 Gb/s with 2-lane operation. The core area of the video clock synthesizer occupies 0.04 mm2 and the power dissipation is 5.5 mW at a low bit rate and 9.1 mW at a high bit rate. The output frequency range is 25 to 330 MHz.ABSTRACT I CONTENTS IV LIST OF FIGURES VII LIST OF TABLES XII CHAPTER 1 INTRODUCTION 1 1.1 BACKGROUND 1 1.2 MOTIVATION 4 1.3 THESIS ORGANIZATION 12 CHAPTER 2 DIGITAL DISPLAY INTERFACE 13 2.1 OVERVIEW 13 2.2 DISPLAYPORT INTERFACE CHARACTERISTICS 18 2.2.1 DISPLAYPORT VERSION 1.2 18 2.2.2 EMBEDDED DISPLAYPORT VERSION 1.2 21 2.3 DISPLAYPORT INTERFACE ARCHITECTURE 23 2.3.1 LAYERED ARCHITECTURE 23 2.3.2 MAIN STREAM PROTOCOL 27 2.3.3 INITIALIZATION AND LINK TRAINING 30 2.3.3 VIDEO STREAM CLOCK RECOVERY 35 CHAPTER 3 DESIGN OF DISPLAYPORT RECEIVER 39 3.1 OVERVIEW 39 3.2 PHYSICAL LAYER 43 3.3 LINK LAYER 55 3.3.1 OVERALL ARCHITECTURE 55 3.3.2 AUX CHANNEL 58 3.3.3 VIDEO TIMING GENERATION 61 3.3.4 CONTENT PROTECTION 63 3.3.5 AUDIO TRANSMISSION 66 3.4 EXPERIMENTAL RESULTS 68 CHAPTER 4 DESIGN OF EMBEDDED DISPLAYPORT RECEIVER 81 4.1 OVERVIEW 81 4.2 PHYSICAL LAYER 84 4.3 LINK LAYER 88 4.3.1 OVERALL ARCHITECTURE 88 4.3.2 MAIN LINK STREAM 90 4.3.3 CONTENT PROTECTION 93 4.4 PROPOSED CLOCK RECOVERY SCHEME 94 4.5 EXPERIMENTAL RESULTS 100 CHAPTER 5 PROPOSED VIDEO CLOCK SYNTHESIZER AND FREQUENCY CONTROL SCHEME 113 5.1 MOTIVATION 113 5.2 PROPOSED VIDEO CLOCK SYNTHESIZER 115 5.3 BUILDING BLOCKS 121 5.4 FREQUENCY ERROR COMPENSATION 126 5.5 EXPERIMENTAL RESULTS 131 CHAPTER 6 CONCLUSION 138 BIBLIOGRAPHY 141 초 록 152Docto

Design of energy efficient high speed I/O interfaces

Energy efficiency has become a key performance metric for wireline high speed I/O interfaces. Consequently, design of low power I/O interfaces has garnered large interest that has mostly been focused on active power reduction techniques at peak data rate. In practice, most systems exhibit a wide range of data transfer patterns. As a result, low energy per bit operation at peak data rate does not necessarily translate to overall low energy operation. Therefore, I/O interfaces that can scale their power consumption with data rate requirement are desirable. Rapid on-off I/O interfaces have a potential to scale power with data rate requirements without severely affecting either latency or the throughput of the I/O interface. In this work, we explore circuit techniques for designing rapid on-off high speed wireline I/O interfaces and digital fractional-N PLLs. A burst-mode transmitter suitable for rapid on-off I/O interfaces is presented that achieves 6 ns turn-on time by utilizing a fast frequency settling ring oscillator in digital multiplying delay-locked loop and a rapid on-off biasing scheme for current mode output driver. Fabricated in 90 nm CMOS process, the prototype achieves 2.29 mW/Gb/s energy efficiency at peak data rate of 8 Gb/s. A 125X (8 Gb/s to 64 Mb/s) change in effective data rate results in 67X (18.29 mW to 0.27 mW) change in transmitter power consumption corresponding to only 2X (2.29 mW/Gb/s to 4.24 mW/Gb/s) degradation in energy efficiency for 32-byte long data bursts. We also present an analytical bit error rate (BER) computation technique for this transmitter under rapid on-off operation, which uses MDLL settling measurement data in conjunction with always-on transmitter measurements. This technique indicates that the BER bathtub width for 10^(−12) BER is 0.65 UI and 0.72 UI during rapid on-off operation and always-on operation, respectively. Next, a pulse response estimation-based technique is proposed enabling burst-mode operation for baud-rate sampling receivers that operate over high loss channels. Such receivers typically employ discrete time equalization to combat inter-symbol interference. Implementation details are provided for a receiver chip, fabricated in 65nm CMOS technology, that demonstrates efficacy of the proposed technique. A low complexity pulse response estimation technique is also presented for low power receivers that do not employ discrete time equalizers. We also present techniques for implementation of highly digital fractional-N PLL employing a phase interpolator based fractional divider to improve the quantization noise shaping properties of a 1-bit ∆Σ frequency-to-digital converter. Fabricated in 65nm CMOS process, the prototype calibration-free fractional-N Type-II PLL employs the proposed frequency-to-digital converter in place of a high resolution time-to-digital converter and achieves 848 fs rms integrated jitter (1 kHz-30 MHz) and -101 dBc/Hz in-band phase noise while generating 5.054 GHz output from 31.25 MHz input

Energy-efficient wireline transceivers

Power-efficient wireline transceivers are highly demanded by many applications in high performance computation and communication systems. Apart from transferring a wide range of data rates to satisfy the interconnect bandwidth requirement, the transceivers have very tight power budget and are expected to be fully integrated. This thesis explores enabling techniques to implement such transceivers in both circuit and system levels. Specifically, three prototypes will be presented: (1) a 5Gb/s reference-less clock and data recovery circuit (CDR) using phase-rotating phase-locked loop (PRPLL) to conduct phase control so as to break several fundamental trade-offs in conventional receivers; (2) a 4-10.5Gb/s continuous-rate CDR with novel frequency acquisition scheme based on bang-bang phase detector (BBPD) and a ring oscillator-based fractional-N PLL as the low noise wide range DCO in the CDR loop; (3) a source-synchronous energy-proportional link with dynamic voltage and frequency scaling (DVFS) and rapid on/off (ROO) techniques to cut the link power wastage at system level. The receiver/transceiver architectures are highly digital and address the requirements of new receiver architecture development, wide operating range, and low power/area consumption while being fully integrated. Experimental results obtained from the prototypes attest the effectiveness of the proposed techniques

데이터 전송로 확장성과 루프 선형성을 향상시킨 다중채널 수신기들에 관한 연구

학위논문 (박사)-- 서울대학교 대학원 : 전기·컴퓨터공학부, 2013. 2. 정덕균.Two types of serial data communication receivers that adopt a multichannel architecture for a high aggregate I/O bandwidth are presented. Two techniques for collaboration and sharing among channels are proposed to enhance the loop-linearity and channel-expandability of multichannel receivers, respectively. The first proposed receiver employs a collaborative timing scheme recovery which relies on the sharing of all outputs of phase detectors (PDs) among channels to extract common information about the timing and multilevel signaling architecture of PAM-4. The shared timing information is processed by a common global loop filter and is used to update the phase of the voltage-controlled oscillator with better rejection of per-channel noise. In addition to collaborative timing recovery, a simple linearization technique for binary PDs is proposed. The technique realizes a high-rate oversampling PD while the hardware cost is equivalent to that of a conventional 2x-oversampling clock and data recovery. The first receiver exploiting the collaborative timing recovery architecture is designed using 45-nm CMOS technology. A single data lane occupies a 0.195-mm2 area and consumes a relatively low 17.9 mW at 6 Gb/s at 1.0V. Therefore, the power efficiency is 2.98 mW/Gb/s. The simulated jitter is about 0.034 UI RMS given an input jitter value of 0.03 UI RMS, while the relatively constant loop bandwidth with the PD linearization technique is about 7.3-MHz regardless of the data-stream noise. Unlike the first receiver, the second proposed multichannel receiver was designed to reduce the hardware complexity of each lane. The receiver employs shared calibration logic among channels and yet achieves superior channel expandability with slim data lanes. A shared global calibration control, which is used in a forwarded clock receiver based on a multiphase delay-locked loop, accomplishes skew calibration, equalizer adaptation, and the phase lock of all channels during a calibration period, resulting in reduced hardware overhead and less area required by each data lane. The second forwarded clock receiver is designed in 90-nm CMOS technology. It achieves error-free eye openings of more than 0.5 UI across 9− 28 inch Nelco 4000-6 microstrips at 4− 7 Gb/s and more than 0.42 UI at data rates of up to 9 Gb/s. The data lane occupies only 0.152 mm2 and consumes 69.8 mW, while the rest of the receiver occupies 0.297 mm2 and consumes 56 mW at a data rate of 7 Gb/s and a supply voltage of 1.35 V.1. Introduction 1 1.1 Motivations 1.2 Thesis Organization 2. Previous Receivers for Serial-Data Communications 2.1 Classification of the Links 2.2 Clocking architecture of transceivers 2.3 Components of receiver 2.3.1 Channel loss 2.3.2 Equalizer 2.3.3 Clock and data recovery circuit 2.3.3.1. Basic architecture 2.3.3.2. Phase detector 2.3.3.2.1. Linear phase detector 2.3.3.2.2. Binary phase detector 2.3.3.3. Frequency detector 2.3.3.4. Charge pump 2.3.3.5. Voltage controlled oscillator and delay-line 2.3.4 Loop dynamics of PLL 2.3.5 Loop dynamics of DLL 3. The Proposed PLL-Based Receiver with Loop Linearization Technique 3.1 Introduction 3.2 Motivation 3.3 Overview of binary phase detection 3.4 The proposed BBPD linearization technique 3.4.1 Architecture of the proposed PLL-based receiver 3.4.2 Linearization technique of binary phase detection 3.4.3 Rotational pattern of sampling phase offset 3.5 PD gain analysis and optimization 3.6 Loop Dynamics of the 2nd-order CDR 3.7 Verification with the time-accurate behavioral simulation 3.8 Summary 4. The Proposed DLL-Based Receiver with Forwarded-Clock 4.1 Introduction 4.2 Motivation 4.3 Design consideration 4.4 Architecture of the proposed forwarded-clock receiver 4.5 Circuit description 4.5.1 Analog multi-phase DLL 4.5.2 Dual-input interpolating deley cells 4.5.3 Dedicated half-rate data samplers 4.5.4 Cherry-Hooper continuous-time linear equalizer 4.5.5 Equalizer adaptation and phase-lock scheme 4.6 Measurement results 5. Conclusion 6. BibliographyDocto

적응형 눈 감지 방법을 포함한 저전력 메모리 컨트롤러의 설계

학위논문 (박사)-- 서울대학교 대학원 공과대학 전기·컴퓨터공학부, 2017. 8. 김수환.and the read margin was enhanced from 0.30UI and 76mV without AF-CTLE to 0.47UI and 80mV to with AF-CTLE. The power efficiency during burst write and read were 5.68pJ/bit and 1.83pJ/bit respectively.A 4266Mb/s/pin LPDDR4 memory controller with an asynchronous feedback continuous-time linear equalizer and an adaptive 3-step eye detection algorithm is presented. The asynchronous feedback continuous-time linear equalizer removes the glitch of DQS without training by applying an offset larger than the noise, and improves read margin by operating as a decision feedback equalizer in DQ path. The adaptive 3-step eye detection algorithm reduces power consumption and black-out time in initialization sequence and retraining in comparison to the 2-dimensional full scanning. In addition, the adaptive 3-step eye detection algorithm can maintain the accuracy by sequentially searching the eye boundaries and initializing the resolution using the binary search method when the eye detection result changes. To achieve high bandwidth, a transmitter and receiver suitable for training are proposed. The transmitter consists of a phase interpolator, a digitally-controlled delay line, a 16:1 serializer, a pre-driver and low-voltage swing terminated logic. The receiver consists of a reference voltage generator, a continuous-time linear equalizer, a phase interpolator, a digitally-controlled delay line, a 1:4 deserializer, and a 4:16 deserializer. The clocking architecture is also designed for low power consumption in idle periods, which are commonly lengthy in mobile applications. A prototype chip was implemented in a 65nm CMOS process with ball grid array package and tested with commodity LPDDR4. The write margin was 0.36UI and 148mVCHAPTER 1 INTRODUCTION 1 1.1 MOTIVATION 1 1.2 THESIS ORGANIZATION 5 CHAPTER 2 LPDDR4 6 2.1 COMPARISON BETWEEN LPDDR3 AND LPDDR4 6 2.2 SOURCE SYNCHRONOUS CLOCKING SCHEME 9 2.3 SIGNALING STANDARDS 11 2.4 MULTIPLE TRAININGS 14 2.5 RE-TRAINING AND RE-INITIALIZATION 16 CHAPTER 3 ADAPTIVE EYE DETECTION 18 3.1 EYE DETECTION 18 3.2 1X2Y3X EYE DETECTION 20 3.3 ADAPTIVE GAIN CONTROL 22 3.4 ADAPTIVE 1X2Y3X EYE DETECTION 24 CHAPTER 4 LPDDR4 MEMORY CONTROLLER 26 4.1 DESIGN PROCEDURE 26 4.2 ARCHITECTURE 30 4.2.1 TRANSMITTER 33 4.2.2 RECEIVER 35 4.2.3 CLOCKING ARCHITECTURE 38 4.3 CIRCUIT IMPLEMENTATION 43 4.3.1 ADPLL WITH MULTI-MODULUS DIVIDER 43 4.3.2 ADDLL WITH TRIANGULAR-MODULATED PI 45 4.3.3 CTLE WITH AUTO-DQS CLEANING 47 4.3.4 DES WITH CLOCK DOMAIN CROSSING 52 4.3.5 LVSTL WITH ZQ CALIBRATION 54 4.3.6 COARSE-FINE DCDL 56 4.4 LINK TRAINING 57 4.4.1 SIMULATION RESULTS 59 CHAPTER 5 MEASUREMENT RESULTS 72 5.1 MEASUREMENT SETUP 72 5.2 MEASUREMENT RESULTS OF SUB-BLOCK 80 5.2.1 ADPLL WITH MULTI-MODULUS DIVIDER 80 5.2.2 ADDLL WITH TRIANGULAR-MODULATED PI 82 5.2.3 COARSE-FINE DCDL 84 5.3 LPDDR4 INTERFACE MEASUREMENT RESULTS 84 CHAPTER 6 CONCLUSION 88 BIBLIOGRAPHY 90Docto