Novel Sub-Harmonic Injection-Locked Balanced Oscillator

A novel sub-harmonic injection-locked balanced oscillator is proposed. The circuit provides two outputs with a 180° ° phase difference by employing a transmission line section for impedance transformation to meet the oscillation conditions. A coupling network is connected at the mid-point of the transmission line to inject the sub-harmonic frequency. This eliminates the need for a circulator or balun. The circuit is small and consumes low DC power. Under the locking state, the circuit provides double the injection frequency and also the phase noise of the two outputs is substantially improved

Super-harmonic injection locking of nano-contact spin-torque vortex oscillators

Super-harmonic injection locking of single nano-contact (NC) spin-torque vortex oscillators (STVOs) subject to a small microwave current has been explored. Frequency locking was observed up to the fourth harmonic of the STVO fundamental frequency $f_{0}$ in microwave magneto-electronic measurements. The large frequency tunability of the STVO with respect to $f_{0}$ allowed the device to be locked to multiple sub-harmonics of the microwave frequency $f_{RF}$, or to the same sub-harmonic over a wide range of $f_{RF}$ by tuning the DC current. In general, analysis of the locking range, linewidth, and amplitude showed that the locking efficiency decreased as the harmonic number increased, as expected for harmonic synchronization of a non-linear oscillator. Time-resolved scanning Kerr microscopy (TRSKM) revealed significant differences in the spatial character of the magnetization dynamics of states locked to the fundamental and harmonic frequencies, suggesting significant differences in the core trajectories within the same device. Super-harmonic injection locking of a NC-STVO may open up possibilities for devices such as nanoscale frequency dividers, while differences in the core trajectory may allow mutual synchronisation to be achieved in multi-oscillator networks by tuning the spatial character of the dynamics within shared magnetic layers.Comment: 21 pages, 8 figure

Design and Analysis of Three-Phase Three-Level PWM Inverter

Design of three-phase three level PWM inverter and analysis of the output current harmonics are presented in this paper. The three-level inverter is designed to supply three-phase load and it is controlled by FPGA under several modulation techniques (Sinusoidal PWM and Third Harmonic Injection PWM). Selection of semiconductor switches and other component of the inverter are described. Inverter output current harmonics under several modulation techniques will be analysed and compared

Highly tunable repetition-rate multiplication of mode-locked lasers using all-fibre harmonic injection locking

Higher repetition-rate optical pulse trains have been desired for various applications such as high-bit-rate optical communication, photonic analogue-to-digital conversion, and multi- photon imaging. Generation of multi GHz and higher repetition-rate optical pulse trains directly from mode-locked oscillators is often challenging. As an alternative, harmonic injection locking can be applied for extra-cavity repetition-rate multiplication (RRM). Here we have investigated the operation conditions and achievable performances of all-fibre, highly tunable harmonic injection locking-based pulse RRM. We show that, with slight tuning of slave laser length, highly tunable RRM is possible from a multiplication factor of 2 to >100. The resulting maximum SMSR is 41 dB when multiplied by a factor of two. We further characterize the noise properties of the multiplied signal in terms of phase noise and relative intensity noise. The resulting absolute rms timing jitter of the multiplied signal is in the range of 20 fs to 60 fs (10 kHz - 1 MHz) for different multiplication factors. With its high tunability, simple and robust all-fibre implementation, and low excess noise, the demonstrated RRM system may find diverse applications in microwave photonics, optical communications, photonic analogue-to-digital conversion, and clock distribution networks.Comment: 25 pages, 9 figure

Influence of third harmonic injection on MMC-based HVDC transmission systems

Whilst third harmonic injection is extensively used in modular multilevel converter (MMC) control, its significant advantages over sinusoidal modulation have not been fully explored. This paper evaluates the influence of third harmonic injection on system power losses, submodule capacitance, circulating current, and fault current and mathematical models are derived. Station conduction losses are reduced by 11%, yielding higher efficiency and lowering cooling system capacity. The submodule capacitance is reduced by 24%, which significantly lowers the capital cost, weight, and volume of the station converter. Additionally, the phase energy variation is reduced by around 18%, which benefits circulating current control. Due to the lower AC currents, the semiconductor current stresses are correspondingly reduced. In addition to the performance improvement in normal operation, the third harmonic injection reduces the DC fault currents by 13.4% and thus the fault current stresses on semiconductors and DC circuit breakers are lowered. Simulation of a point-to-point HVDC system demonstrates the effectiveness of the above analysis

Optimized design of harmonic-injection dividers

A new formulation is presented for the efficient harmonic-balance analysis of the division bandwidth of frequency dividers by a high order. The procedure is based on some mathematical properties of the solution curve under low-amplitude of the input generator. Through a simple fitting technique, it is possible to determine the variation of the synchronization bandwidth versus any design parameter, while keeping constant the central frequency of the division band. The procedure also enables a prediction of the frequency-division interval for any value of the input-generator amplitude within the region of linear behavior with respect to the input source. It has been applied to the optimization of the input matching network in a frequency divider by 10, which uses a nonlinear transmission line (NLTL) as a feedback network.Spanish project TEC2011-29264-C03-01 for financial support

The effect of inrush transients on pv inverter's grid impedance measurement based on inter-harmonic injection

This paper addresses a cause for false tripping of photovoltaic inverters with antiislanding protection based on impedance measurement with inter-harmonic injection. Earlier discussions about tripping problems happening when several devices are doing the measurement at the same time are supplemented with a problem caused by inrush transients of nearby devices. A series of experiments was conducted in the Power Quality laboratory of the TU/e, on a PV inverter which complies with the DIN VDE 0126 standard. Impedance measurement was done in parallel with the inverter and measurement results are presented. A criterion for false tripping caused by transients is explored. Also, influences of network impedance and grid harmonic pollution on false tripping were analyzed. In the end, some signal processing techniques are proposed to avoid this problem

Multiphase induction motor drives - a technology status review

The area of multiphase variable-speed motor drives in general and multiphase induction motor drives in particular has experienced a substantial growth since the beginning of this century. Research has been conducted worldwide and numerous interesting developments have been reported in the literature. An attempt is made to provide a detailed overview of the current state-of-the-art in this area. The elaborated aspects include advantages of multiphase induction machines, modelling of multiphase induction machines, basic vector control and direct torque control schemes and PWM control of multiphase voltage source inverters. The authors also provide a detailed survey of the control strategies for five-phase and asymmetrical six-phase induction motor drives, as well as an overview of the approaches to the design of fault tolerant strategies for post-fault drive operation, and a discussion of multiphase multi-motor drives with single inverter supply. Experimental results, collected from various multiphase induction motor drive laboratory rigs, are also included to facilitate the understanding of the drive operatio