Simultaneous Estimation of Berberine and Quercetin in Pathydi Kada Formulation by Hptlc

A sensitive, selective and precise thin-layer chromatographic method has been developed and validated for the analysis of Berberine and Quercetin in Pathydi Kada laboratory prepared and Market formulation. Separation and quantification were achieved by TLC using mobile phase of Ethyl acetate: Methanol: Glacial acetic acid (6: 4: 0.5) v/v/v (Rf 0.2 & 0.84 for Berberine and Quercetin respectively) on precoated silica gel 60F254 aluminum plates and determination was carried out at 254 and 366 nm for berberine and quercetin respectively. The calibration curve was linear in the concentration range of 4-12 μg spot-1. The method was validated for precision, repeatability and accuracy. The proposed method was found to be simple, precise, specific, sensitive and accurate for the quantification of Berberine and Quercetin. This is the first TLC report for the simultaneous estimation of Berberine and Quercetin in Pathydi Kada formulation and may be useful for the routine quality control

Resistive Switching Memory Properties of Electrodeposited Cu2O Thin Films

The Cu2O thin film was developed using an electrodeposition approach for resistive memory application. The impact of the deposition voltage (1V, 2V, 3V, and 4V) on resistive switching (RS)/memristive properties of Cu2O thin films was studied. The XRD spectrum reveals that deposited Cu2O has a cubic crystal structure. The bipolar RS in Al/Cu2O/FTO device was clearly observed during the current-voltage (I-V) measurement. The basic memristive properties were calculated from I-V data. The charge transport studies suggested that the SCLC mechanism was responsible for device conduction, and RS was due to filamentary effect. The result suggested that the electrodeposition technique is useful to fabricate a memristive device for various applications

Robust estimation of bacterial cell count from optical density

Optical density (OD) is widely used to estimate the density of cells in liquid culture, but cannot be compared between instruments without a standardized calibration protocol and is challenging to relate to actual cell count. We address this with an interlaboratory study comparing three simple, low-cost, and highly accessible OD calibration protocols across 244 laboratories, applied to eight strains of constitutive GFP-expressing E. coli. Based on our results, we recommend calibrating OD to estimated cell count using serial dilution of silica microspheres, which produces highly precise calibration (95.5% of residuals <1.2-fold), is easily assessed for quality control, also assesses instrument effective linear range, and can be combined with fluorescence calibration to obtain units of Molecules of Equivalent Fluorescein (MEFL) per cell, allowing direct comparison and data fusion with flow cytometry measurements: in our study, fluorescence per cell measurements showed only a 1.07-fold mean difference between plate reader and flow cytometry data

Calibration of the CMS hadron calorimeters using proton-proton collision data at root s=13 TeV

Methods are presented for calibrating the hadron calorimeter system of theCMSetector at the LHC. The hadron calorimeters of the CMS experiment are sampling calorimeters of brass and scintillator, and are in the form of one central detector and two endcaps. These calorimeters cover pseudorapidities vertical bar eta vertical bar ee data. The energy scale of the outer calorimeters has been determined with test beam data and is confirmed through data with high transverse momentum jets. In this paper, we present the details of the calibration methods and accuracy.Peer reviewe

31st Annual Meeting and Associated Programs of the Society for Immunotherapy of Cancer (SITC 2016) : part two

Background The immunological escape of tumors represents one of the main ob- stacles to the treatment of malignancies. The blockade of PD-1 or CTLA-4 receptors represented a milestone in the history of immunotherapy. However, immune checkpoint inhibitors seem to be effective in specific cohorts of patients. It has been proposed that their efficacy relies on the presence of an immunological response. Thus, we hypothesized that disruption of the PD-L1/PD-1 axis would synergize with our oncolytic vaccine platform PeptiCRAd. Methods We used murine B16OVA in vivo tumor models and flow cytometry analysis to investigate the immunological background. Results First, we found that high-burden B16OVA tumors were refractory to combination immunotherapy. However, with a more aggressive schedule, tumors with a lower burden were more susceptible to the combination of PeptiCRAd and PD-L1 blockade. The therapy signifi- cantly increased the median survival of mice (Fig. 7). Interestingly, the reduced growth of contralaterally injected B16F10 cells sug- gested the presence of a long lasting immunological memory also against non-targeted antigens. Concerning the functional state of tumor infiltrating lymphocytes (TILs), we found that all the immune therapies would enhance the percentage of activated (PD-1pos TIM- 3neg) T lymphocytes and reduce the amount of exhausted (PD-1pos TIM-3pos) cells compared to placebo. As expected, we found that PeptiCRAd monotherapy could increase the number of antigen spe- cific CD8+ T cells compared to other treatments. However, only the combination with PD-L1 blockade could significantly increase the ra- tio between activated and exhausted pentamer positive cells (p= 0.0058), suggesting that by disrupting the PD-1/PD-L1 axis we could decrease the amount of dysfunctional antigen specific T cells. We ob- served that the anatomical location deeply influenced the state of CD4+ and CD8+ T lymphocytes. In fact, TIM-3 expression was in- creased by 2 fold on TILs compared to splenic and lymphoid T cells. In the CD8+ compartment, the expression of PD-1 on the surface seemed to be restricted to the tumor micro-environment, while CD4 + T cells had a high expression of PD-1 also in lymphoid organs. Interestingly, we found that the levels of PD-1 were significantly higher on CD8+ T cells than on CD4+ T cells into the tumor micro- environment (p < 0.0001). Conclusions In conclusion, we demonstrated that the efficacy of immune check- point inhibitors might be strongly enhanced by their combination with cancer vaccines. PeptiCRAd was able to increase the number of antigen-specific T cells and PD-L1 blockade prevented their exhaus- tion, resulting in long-lasting immunological memory and increased median survival

Optimization of surface roughness in milling of EN 24 steel with WC-Coated inserts using response surface methodology: analysis using surface integrity microstructural characterizations

Introduction: Among alloys of medium-carbon and high-strength steel, EN 24 steel is characterised by its nickel-chromium-molybdenum composition. EN 24 steel is highly suitable for application in heavy-duty projects due to its notable resilience to damage, especially when exposed to low temperatures. With the objective of minimising surface irregularities, this research endeavours to enhance the milling process of EN 24 steel by employing coated tungsten carbide (WC) tool inserts.Methods: Feed rate, cutting speed, depth of cut, and cutting fluid are all crucial process factors in the experimental investigation. Four distinct levels are applied to each factor. The research utilises the Design of Experiments (DOE)-based Central Composite Design of Response Surface Methodology. To predict output parameters, mathematical models are developed utilising analysis of variance (ANOVA) for optimisation purposes.Results and discussions: Through the utilisation of multi-objective optimisation, the optimal combination for tungsten carbide inserts was determined, which provided surface irregularities of 0.301 µm. Cutting speed (CS) of 149.507 m/min, feed rate (FR) of 340.27 mm/min, depth of cut (DOC) of 0.599 mm, and cutting fluid (CF) of 12.50 L/min are the optimal parameters. The surface morphologies of the machined workpiece at particular parameter values can be discerned through scanning electron microscope (SEM) analysis, yielding significant insights. The optimal parameters that have been identified provide practical recommendations for improving the milling method of EN 24 steel when tungsten carbide inserts are utilised. Understanding the milling process in its entirety is facilitated by SEM analysis of surface morphologies and microstructures under particular cutting conditions. The morphology and surface irregularities of the machined workpiece are evaluated using profilometry, which provides additional insight into surface integrity. The discourse investigates the potential applications and implications of the results, as well as suggests directions for further study concerning the enhancement of milling processes for similar steel alloys

Spike-time dependent plasticity of tailored ZnO nanorod-based resistive memory for synaptic learning

Metal oxide resistive memory is a potential device that can substantially influence the current roadmap for nonvolatile memory and neuromorphic computing. However, common amorphous oxide-based resistive random-access memory suffers from high forming voltages that complicate circuit design and abrupt SET behavior incompatible with analog weight updates. To overcome such limitations, wurtzite ZnO nanorods were synthesized on a fluorine-doped tin oxide (FTO) substrate and a bipolar resistive memory with the Ag/w-ZnO/FTO stacking sequence was fabricated. The hexagonal NR morphology of w-ZnO with controlled vertical growth and nanochannel formation between the NRs were produced by in situ crystalline growth. This morphology enabled a forming-free switching and an analog switching effect that emulated neuromorphic functionalities such as potentiation–depression and complex spike-time dependent plasticity-based Hebbian learning rules. Importantly, the device exhibited nonabrupt switching behavior suitable for analog weight updates in neuromorphic computing in contrast to conventional resistive memory