53 research outputs found

    Measuring Input Thresholds on an Existing Board

    Get PDF
    A critical PECL (positive emitter-coupled logic) interface to Xilinx interface needed to be changed on an existing flight board. The new Xilinx input interface used a CMOS (complementary metal-oxide semiconductor) type of input, and the driver could meet its thresholds typically, but not in worst-case, according to the data sheet. The previous interface had been based on comparison with an external reference, but the CMOS input is based on comparison with an internal divider from the power supply. A way to measure what the exact input threshold was for this device for 64 inputs on a flight board was needed. The measurement technique allowed an accurate measurement of the voltage required to switch a Xilinx input from high to low for each of the 64 lines, while only probing two of them. Directly driving an external voltage was considered too risky, and tests done on any other unit could not be used to qualify the flight board. The two lines directly probed gave an absolute voltage threshold calibration, while data collected on the remaining 62 lines without probing gave relative measurements that could be used to identify any outliers. The PECL interface was forced to a long-period square wave by driving a saturated square wave into the ADC (analog to digital converter). The active pull-down circuit was turned off, causing each line to rise rapidly and fall slowly according to the input s weak pull-down circuitry. The fall time shows up as a change in the pulse width of the signal ready by the Xilinx. This change in pulse width is a function of capacitance, pulldown current, and input threshold. Capacitance was known from the different trace lengths, plus a gate input capacitance, which is the same for all inputs. The pull-down current is the same for all inputs including the two that are probed directly. The data was combined, and the Excel solver tool was used to find input thresholds for the 62 lines. This was repeated over different supply voltages and temperatures to show that the interface had voltage margin under all worst case conditions. Gate input thresholds are normally measured at the manufacturer when the device is on a chip tester. A key function of this machine was duplicated on an existing flight board with no modifications to the nets to be tested, with the exception of changes in the FPGA program

    CoNNeCT Baseband Processor Module

    Get PDF
    A document describes the CoNNeCT Baseband Processor Module (BPM) based on an updated processor, memory technology, and field-programmable gate arrays (FPGAs). The BPM was developed from a requirement to provide sufficient computing power and memory storage to conduct experiments for a Software Defined Radio (SDR) to be implemented. The flight SDR uses the AT697 SPARC processor with on-chip data and instruction cache. The non-volatile memory has been increased from a 20-Mbit EEPROM (electrically erasable programmable read only memory) to a 4-Gbit Flash, managed by the RTAX2000 Housekeeper, allowing more programs and FPGA bit-files to be stored. The volatile memory has been increased from a 20-Mbit SRAM (static random access memory) to a 1.25-Gbit SDRAM (synchronous dynamic random access memory), providing additional memory space for more complex operating systems and programs to be executed on the SPARC. All memory is EDAC (error detection and correction) protected, while the SPARC processor implements fault protection via TMR (triple modular redundancy) architecture. Further capability over prior BPM designs includes the addition of a second FPGA to implement features beyond the resources of a single FPGA. Both FPGAs are implemented with Xilinx Virtex-II and are interconnected by a 96-bit bus to facilitate data exchange. Dedicated 1.25- Gbit SDRAMs are wired to each Xilinx FPGA to accommodate high rate data buffering for SDR applications as well as independent SpaceWire interfaces. The RTAX2000 manages scrub and configuration of each Xilinx

    Committing to ecological restoration: Efforts around the globe need legal and policy clarification

    Get PDF
    At the September 2014 United Nations Climate Summit, governments rallied around an international agreement—the New York Declaration on Forests—that underscored restoration of degraded ecosystems as an auspicious solution to climate change. Ethiopia committed to restore more than one-sixth of its land. Uganda, the Democratic Republic of Congo, Guatemala, and Colombia pledged to restore huge areas within their borders. In total, parties committed to restore a staggering 350 million hectares by 2030.Fil: Suding, Kathering. State University Of Colorado-boulder; Estados UnidosFil: Higgs, Eric. University Of Victoria; CanadáFil: Palmer, Margaret. University of Maryland; Estados UnidosFil: Callicott, J. Baird. University Of North Texas; Estados UnidosFil: Anderson, Christopher Brian. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Austral de Investigaciones Científicas; ArgentinaFil: Baker, Matthew. University Of Maryland; Estados UnidosFil: Gutrich, John J.. Southern Oregon University; Estados UnidosFil: Hondula, Kelly L.. University of Maryland; Estados UnidosFil: Lafevor, Matthew C.. University of Maryland; Estados UnidosFil: Larson, Brendon M. H.. University Of Waterloo; CanadáFil: Randall, Alan. Ohio State University; Estados Unidos. University Of Sidney; AustraliaFil: Ruhl, J. B.. Vanderbilt University; Estados UnidosFil: Schwartz, Katrina Z. S.. Woodrow Wilson International Center for Scholars; Estados Unido

    Red Imported Fire Ant in Australia: What if we lose the war?

    Get PDF
    In Australia, a national eradication programme for the Red Imported Fire Ant (Solenopsis invicta Buren), one of the world's most invasive species, has been in operation since 2001 when the pest was first detected in Brisbane, Queensland. Since that time, four separate incursions of this ant have been successfully eradicated from this country, but the main Brisbane population remains. Cost-benefit analyses already conducted put the likely impact of Red Imported Fire Ant in Australia, if not eradicated, at between A8.5andA8.5 and A45 billion. Despite this, ongoing funding for the eradication programme is not assured. A recent external review has concluded that it remains technically feasible, cost beneficial and in the national interest to eradicate. In support of previous analyses, our study highlights some of the potential impacts of Red Imported Fire Ant in Australia in more detail and provides case examples. Results show that adverse impacts are likely in most sectors of the economy, and will be felt not only by agricultural industries, but also the building and construction, tourism, electrical and communications industries. In addition to industry effects, there will also be negative impacts on public health and lifestyle, the environment and infrastructure such as main roads, airports and schools. Our estimates of potential cost impacts in the case examples where extrapolation was possible exceed A$1.65 billion/year and support previous predictions. We conclude that increased spending is justified to avert ‘invasion debt’ – the future cost of battling pests that escape today. This is a war that Australia cannot afford to lose

    Voluntary Restoration: Mitigation's Silent Partner in the Quest to Reverse Coastal Wetland Loss in the USA

    Get PDF
    Copyright © 2019 Gittman, Baillie, Arkema, Bennett, Benoit, Blitch, Brun, Chatwin, Colden, Dausman, DeAngelis, Herold, Henkel, Houge, Howard, Hughes, Scyphers, Shostik, Sutton-Grier and Grabowski. This is an open-access article distributed under the terms of the Creative Commons Attribution License (CC BY). The use, distribution or reproduction in other forums is permitted, provided the original author(s) and the copyright owner(s) are credited and that the original publication in this journal is cited, in accordance with accepted academic practice. No use, distribution or reproduction is permitted which does not comply with these terms
    • …
    corecore