CFRP strengthened continuous concrete beams.

yesThis paper reports the testing of five reinforced concrete continuous beams strengthened in flexure with externally bonded carbon-fibre-reinforced polymer (CFRP) laminates. All beams had the same geometrical dimensions and internal steel reinforcement. The main parameters studied were the position and form of the CFRP laminates. Three of the beams were strengthened using different arrangements of CFRP plate reinforcement, and one was strengthened using CFRP sheets. The performance of the CFRP-strengthened beams was compared with that of an unstrengthened control beam. Peeling failure was the dominant mode of failure for all the strengthened beams tested. The beam strengthened with both top and bottom CFRP plates produced the highest load capacity. It was found that the longitudinal elastic shear stresses at the adhesive/concrete interface calculated at beam failure were close to the limiting value recommended in Concrete Society Technical Report 55

Design and experimental verification of a 50 kW interior permanent magnet synchronous machine

This paper presents the design details for an IPM machine designed to deliver 50 kW constant power over a 5:1 speed range extending from 850 rpm to 4250 rpm, with a gradual reduction in the required output power up to 8000 rpm (25 kW). Electromagnetic, thermal, and structural considerations have been included in the design optimization process. The resulting machine is designed with two magnet layers per pole and a distributed stator winding. Special features of the machine include its deep stator slots and four-layer winding, made necessary by the desire to minimize the machine's moment of inertia. Test results available to date demonstrate that the machine is capable of delivering the required output torque and power, and the agreement between the predicted and measured machine parameters is generally quite good. Calculated iron losses for high-speed flux-weakening operation are presented in the final section of the paper, illustrating the challenges associated with minimizing the impact of high-frequency harmonic flux density components.Jahns, T.M.; Seok-Hee Han; El-Refaie, A.M.; Jei-Hoon Baek; Aydin, M.; Guven, M.K.; Soong, W.L

3D thermal analysis of a permanent magnet motor with cooling fans

Overheating of permanent magnet (PM) machines has become a major technical challenge as it gives rise to magnet demagnetization, degradation of insulation materials, and loss of motor efficiency. This paper proposes a state-of-the-art cooling system for an axial flux permanent magnet (AFPM) machine with the focus on its structural optimization. A computational fluid dynamics (CFD) simulation with thermal consideration has been shown to be an efficient approach in the literature and is thus employed in this work. Meanwhile, a simplified numerical approach to the AFPM machine with complex configuration in 3D consisting of conduction, forced convection, and conjugate heat transfer is taken as a case study. Different simplification methods (including configuration and working conditions) and two optimized fans for forced convection cooling are designed and installed on the AFPM machine and compared to a natural convection cooling system. The results show that the proposed approach is effective for analyzing the thermal performance of a complex AFPM machine and strikes a balance between reasonable simplification, accuracy, and computational resource

IEEE Access special section editorial: Advanced energy conversion systems based on multi-port electrical machines

Over the last decade, with the merits of high efficiency, compactness, and flexibility, energy conversion systems based on multiple-electrical-port and multiple-mechanicalport electrical machines have attracted widespread attention from both academia and industry. This concept has been adopted in many industrial applications, such as wind power generation, ship shaft power generation, ship electric propulsion, electric vehicles, rail transportation, more/all electric aircrafts, and ac/dc microgrids. Due to the ever-increasing demand for highly reliable and cost-effective energy conversion systems, advanced machine/converter topologies, modeling approaches, control strategies, and reliability, evaluations of multi-port electrical machines and drive systems are in great need

Size of FRP laminates to strengthen reinforced concrete sections in flexure.

yesThis paper presents an analytical method for estimating the flexural strength of reinforced concrete beams strengthened with externally bonded fibre reinforced polymer (FRP) laminates. The method is developed from the strain compatibility and equilibrium of forces. Based on the size of external FRP laminates, several flexural failure modes may be identified, namely tensile rupture of FRP laminates and concrete crushing before or after yielding of internal steel reinforcement. Upper and lower limits to the size of FRP laminates used are suggested to maintain ductile behaviour of strengthened reinforced concrete sections. Comparisons between the flexural strength obtained from the current method and experiments show good agreement. Design equations for calculating the size of FRP laminates externally bonded to reinforced concrete sections to enhance their flexural strength are proposed

A systematic review of techniques and effects of self-help interventions for tinnitus: application of taxonomies from health psychology

Objective: Self-help interventions are followed by people independently with minimal or no therapist contact. This review aims to assess the effectiveness of self-help interventions for adults with chronic tinnitus and systematically identify the self-help techniques used. Design: Systematic review and application of health psychology taxonomies. Electronic database searches were conducted, supplemented by citation searching and hand-searching of key journals. Prospective controlled trials, which used measures of tinnitus distress, functional management, anxiety, depression, and quality of life, were included. Michie et al’s behaviour change techniques (BCTs) taxonomy and Taylor et al’s PRISMS taxonomy of self-management components were applied to describe interventions. Study sample: Five studies were included, providing low-to-moderate levels of evidence. Results: Randomized controlled trial studies were too few and heterogeneous for meta-analysis to be performed. Studies comparing self-help interventions to therapist-guided interventions and assessing non tinnitus-specific psychosocial outcomes and functional management were lacking. Fifteen BCTs and eight self-management components were identified across interventions. Conclusions: A lack of high-quality and homogeneous studies meant that confident conclusions could not be drawn regarding the efficacy of self-help interventions for tinnitus. Better reporting and categorization of intervention techniques is needed for replication in research and practice and to facilitate understanding of intervention mechanisms

GIZA 11 AND GIZA 12; TWO NEW FLAX DUAL PURPOSE TYPE VARIETIES

Sixteen flax genotypes {13 promising lines and 3 check varieties viz., Giza 8 (oil type), Sakha 1 (dual purpose type) and Sakha 3 (fiber type)} were evaluated for straw, seed, oil yields and their related traits under twelve different environments; four locations (Sakha, Etay El-Baroud, Ismailia and Giza Exp. Stations through three successive seasons (2011/12, 2012/13 and 2013/14). These materials were evaluated in a randomized complete blocks design with three replications at the twelve above-mentioned environments. The analysis of variance revealed highly significant differences among genotypes (G), environments (E) and G x E interaction for all studied traits except straw weight per plant, indicating a wide range of variation among genotypes, environments and these genotypes exhibited differential response to environmental conditions. The significant variance due to residual for all characters except both straw weight per plant and oil yield per fad indicated that genotypes differed with respect to their stability suggesting that prediction would be difficult, which means that mean performance alone would not be appropriate. Interaction component of variance (σ2ge) was less than the genotypic variance (σ2g) for all characters, indicating that genotypes differ in their genetic potential for these traits. This was reflected in high heritability and low discrepancy between phenotypic (PCV) and genotypic (GCV) coefficients of variability values for these traits indicating the possibility of using each of long fiber percentage, plant height and technical stem length as selection indices for improving straw weight per plant, as well as, using 1000-seed weight and capsules number per plant as selection indices for improving seed weight per plant. Yield stability (YSi) statistic indicated that S.541-C/3 and S.541-D/10 gave high mean performance and stability for straw, fiber, seed and oil yields per fad in addition to oil percentage, capsules number per plant and 1000-seed weight. Therefore, the two genotypes well be released under the name Giza 11 and Giza 12, respectively. These newly released varieties are of dual purpose type for straw, fiber, seed and oil yield. They may replace the low yielding cultivars Giza 8, Sakha 1 and Sakha 3

Comparison between transfer path analysis methods on an electric vehicle

A comparison between transfer path analysis and operational path analysis methods using an electric vehicle is presented in this study. Structure-borne noise paths to the cabin from different engine and suspension points have been considered. To realise these methods, two types of test have been performed; operational tests on a rolling road and hammer tests in static conditions. The main aim of this work is assessing the critical paths which are transmitting the structure-borne vibrations from the electric vehicle?s vibration sources to the driver?s ear. This assessment includes the analysis of the noise contribution of each path depending on the frequency and vehicle speed range and moreover, the assessment of the path noise impact for harmonic orders which arise due to the physical components of the electric vehicle. Furthermore, the applicability of these methods to electric vehicles is assessed as these techniques have been extensively used for vehicles powered with internal combustion engines.The authors would like to acknowledge the COST ACTION TU1105 for supporting this research

Developing cartoons for long-term condition self-management information

Background: Advocating the need to adopt more self-management policies has brought with it an increasing demand for information about living with and making decisions about long-term conditions, with a significant potential for using cartoons. However, the purposeful use of cartoons is notably absent in many areas of health care as is evidence of their acceptability to patients and lay others. This paper outlines the process used to develop and evaluate cartoons and their acceptability for a series of self-management guidebooks for people with inflammatory bowel disease, irritable bowel syndrome, diabetes, chronic obstructive pulmonary disease and chronic kidney disease (CKD). Methods: Principles for a process to develop information and cartoons were developed. Cartoon topics were created using qualitative research methods to obtain lay views and experiences. The CKD guidebook was used to provide a detailed exemplar of the process. Focus group and trial participants were recruited from primary care CKD registers. The book was part of a trial intervention; selected participants evaluated the cartoons during in-depth interviews which incorporated think-aloud methods. Results: In general, the cartoons developed by this process depict patient experiences, common situations, daily management dilemmas, making decisions and choices and the uncertainties associated with conditions. CKD cartoons were developed following two focus groups around the themes of getting a diagnosis; understanding the problem; feeling that facts were being withheld; and setting priorities. Think-aloud interviews with 27 trial participants found the CKD cartoons invoked amusement, recognition and reflection but were sometimes difficult to interpret. Conclusion: Humour is frequently utilised by people with long-term conditions to help adjustment and coping. Cartoons can help provide clarity and understanding and could address concerns related to health literacy. Using cartoons to engage and motivate people is a consideration untapped by conventional theories with the potential to improve information to support self-management