Properties of sediments deposited in a fluid with different pH

This is the author accepted manuscript. The final version is available from Taylor & Francis via the DOI in this recordThe effect of pH on the physical and mechanical properties of a sediment was investigated through a set of experimental tests. The sediment was formed from deposition of suspended particles in a fluid. Two different types of clay soil were suspended in fluids with different pH (2, 4, 7, 9 and 11) in cylindrical tubes with volume of 1 liter and also in special cylindrical reservoirs. The height of the sediment was measured in the cylindrical tube until equilibrium was achieved. The sediment deposited in the reservoirs was dried in air and then Atterberg limit, compaction and unconfined compressive strength (UCS) tests were conducted on samples prepared from each sediment. The results showed that the final height of the settled sediment is a function of pH; the height of sediment is increased with increasing the pH. Also, the Atterberg limits increased with increasing the pH. The maximum dry unit weight and optimum water content decreased and increased with increasing the pH. The final strength of the sediment decreased with increasing pH. Based on the SEM analysis, it was found that the values of pH influence the properties of the formed sediments

Effect of forced carbonation on the behaviour of a magnesia-stabilised clay soil

This is the author accepted manuscript. The final version is available from Routledge via the DOI in this recordThis paper presents an investigation into the behaviour of a clay soil stabilised with MgO under forced carbonation and comparison with conventional chemical stabilisation methods. The tests were conducted in two groups. In the first group the soil was mixed with 5, 10, 15 and 20% MgO or cement. Unconfined compressive strength (UCS) tests were performed on compacted samples from these mixtures at curing times of 7, 14 and 28 days. In the second group, samples prepared with different percents of MgO were subjected to CO2 under pressures of 0.5, 1.0 and 1.5 bar for periods of 4, 8, 12 and 24 h. The results showed that adding MgO increases the strength of the soil and, like other binders, the amount of increase in strength depends on the percent of MgO and curing time. It is also resulted that the effect of MgO is less than cement in increasing the strength. It was revealed that forced carbonation can facilitate the stabilisation of MgO-stabilised soil in a few hours compared with usual process that takes several days. XRD and SEM results showed that the gained strength is resulted from the interaction between the soil and the agents

Missing paternal demographics: A novel indicator for identifying high risk population of adverse pregnancy outcomes

BACKGROUND: One of every 6 United Status birth certificates contains no information on fathers. There might be important differences in the pregnancy outcomes between mothers with versus those without partner information. The object of this study was to assess whether and to what extent outcomes in pregnant women who did not have partner information differ from those who had. METHODS: We carried out a population-based retrospective cohort study based on the registry data in the United States for the period of 1995–1997, which was a matched multiple birth file (only twins were included in the current analysis). We divided the study subjects into three groups according to the availability of partner information: available, partly missing, and totally missing. We compared the distribution of maternal characteristics, maternal morbidity, labor and delivery complications, obstetric interventions, preterm birth, fetal growth restriction, low birth weight, congenital anomalies, fetal death, neonatal death, post-neonatal death, and neonatal morbidity among three study groups. RESULTS: There were 304466 twins included in our study. Mothers whose partner's information was partly missing and (especially) totally missing tended to be younger, of black race, unmarried, with less education, smoking cigarette during pregnancy, and with inadequate prenatal care. The rates of preterm birth, fetal growth restriction, low birth weight, Apgar score <7, fetal mortality, neonatal mortality, and post-neonatal mortality were significantly increased in mothers whose partner's information was partly or (especially) totally missing. CONCLUSIONS: Mothers whose partner's information was partly and (especially) totally missing are at higher risk of adverse pregnant outcomes, and clinicians and public health workers should be alerted to this important social factor

Global, regional, and national comparative risk assessment of 79 behavioural, environmental and occupational, and metabolic risks or clusters of risks, 1990-2015: a systematic analysis for the Global Burden of Disease Study 2015

SummaryBackground The Global Burden of Diseases, Injuries, and Risk Factors Study 2015 provides an up-to-date synthesis of the evidence for risk factor exposure and the attributable burden of disease. By providing national and subnational assessments spanning the past 25 years, this study can inform debates on the importance of addressing risks in context. Methods We used the comparative risk assessment framework developed for previous iterations of the Global Burden of Disease Study to estimate attributable deaths, disability-adjusted life-years (DALYs), and trends in exposure by age group, sex, year, and geography for 79 behavioural, environmental and occupational, and metabolic risks or clusters of risks from 1990 to 2015. This study included 388 risk-outcome pairs that met World Cancer Research Fund-defined criteria for convincing or probable evidence. We extracted relative risk and exposure estimates from randomised controlled trials, cohorts, pooled cohorts, household surveys, census data, satellite data, and other sources. We used statistical models to pool data, adjust for bias, and incorporate covariates. We developed a metric that allows comparisons of exposure across risk factors—the summary exposure value. Using the counterfactual scenario of theoretical minimum risk level, we estimated the portion of deaths and DALYs that could be attributed to a given risk. We decomposed trends in attributable burden into contributions from population growth, population age structure, risk exposure, and risk-deleted cause-specific DALY rates. We characterised risk exposure in relation to a Socio-demographic Index (SDI). Findings Between 1990 and 2015, global exposure to unsafe sanitation, household air pollution, childhood underweight, childhood stunting, and smoking each decreased by more than 25%. Global exposure for several occupational risks, high body-mass index (BMI), and drug use increased by more than 25% over the same period. All risks jointly evaluated in 2015 accounted for 57·8% (95% CI 56·6–58·8) of global deaths and 41·2% (39·8–42·8) of DALYs. In 2015, the ten largest contributors to global DALYs among Level 3 risks were high systolic blood pressure (211·8 million [192·7 million to 231·1 million] global DALYs), smoking (148·6 million [134·2 million to 163·1 million]), high fasting plasma glucose (143·1 million [125·1 million to 163·5 million]), high BMI (120·1 million [83·8 million to 158·4 million]), childhood undernutrition (113·3 million [103·9 million to 123·4 million]), ambient particulate matter (103·1 million [90·8 million to 115·1 million]), high total cholesterol (88·7 million [74·6 million to 105·7 million]), household air pollution (85·6 million [66·7 million to 106·1 million]), alcohol use (85·0 million [77·2 million to 93·0 million]), and diets high in sodium (83·0 million [49·3 million to 127·5 million]). From 1990 to 2015, attributable DALYs declined for micronutrient deficiencies, childhood undernutrition, unsafe sanitation and water, and household air pollution; reductions in risk-deleted DALY rates rather than reductions in exposure drove these declines. Rising exposure contributed to notable increases in attributable DALYs from high BMI, high fasting plasma glucose, occupational carcinogens, and drug use. Environmental risks and childhood undernutrition declined steadily with SDI; low physical activity, high BMI, and high fasting plasma glucose increased with SDI. In 119 countries, metabolic risks, such as high BMI and fasting plasma glucose, contributed the most attributable DALYs in 2015. Regionally, smoking still ranked among the leading five risk factors for attributable DALYs in 109 countries; childhood underweight and unsafe sex remained primary drivers of early death and disability in much of sub-Saharan Africa. Interpretation Declines in some key environmental risks have contributed to declines in critical infectious diseases. Some risks appear to be invariant to SDI. Increasing risks, including high BMI, high fasting plasma glucose, drug use, and some occupational exposures, contribute to rising burden from some conditions, but also provide opportunities for intervention. Some highly preventable risks, such as smoking, remain major causes of attributable DALYs, even as exposure is declining. Public policy makers need to pay attention to the risks that are increasingly major contributors to global burden. Funding Bill & Melinda Gates Foundation

Petrographical and geochemical evidences for paragenetic sequence interpretation of diagenesis in mixed siliciclastic–carbonate sediments: Mozduran Formation (Upper Jurassic), south of Agh-Darband, NE Iran

The Upper Jurassic Mozduran Formation with a thickness of 420 m at the type locality is the most important gas-bearing reservoir in NE Iran. It is mainly composed of limestone, dolostone with shale and gypsum interbeds that grade into coarser siliciclastics in the easternmost part of the basin. Eight stratigraphic sections were studied in detail in south of the Agh-Darband area. These analyses suggest that four carbonate facies associations and three siliciclastic lithofacies were deposited in shallow marine to shoreline environments, respectively. Cementation, compaction, dissolution, micritization, neomorphism, hematitization, dolomitization and fracturing are diagenetic processes that affected these sediments.Stable isotope variations of δ18O and δ13C in carbonate rocks show two different trends. High depletion of δ18O and low variation of δ13C probably reflect increasing temperatures during burial diagenesis, while the higher depletion in carbon isotope values with low variations in oxygen isotopes are related to fresh water flushing during meteoric diagenesis. Negative values of carbon isotopes may have also resulted from organic matter alteration during penetration of meteoric water. Fe and Mn enrichment with depletion of δ18O also supports the contention that alteration associated with higher depletion in carbon isotope values with low variations in oxygen isotopes took place during meteoric diagenesis. The presence of bright luminescence indicates redox conditions during precipitation of calcite cement

Prevalence of diabetic retinopathy in Tehran province: a population-based study

<p>Abstract</p> <p>Background</p> <p>To determine the prevalence and characteristics of diabetic retinopathy (DR) among Iranian patients with diabetes.</p> <p>Methods</p> <p>Design: population-based cross-sectional study.</p> <p>Participants: patients with diabetes aged 25 to 64 years in Tehran province, Iran. This survey was conducted from April to October 2007. The study sample was derived from the first national survey of risk factors for non-communicable disease. Diabetes mellitus was defined as a fasting plasma glucose of ≥ 7.0 mmol/l (126 mg/dl) or more, use of diabetic medications, or a physician's diagnosis of diabetes. All patients known to have diabetes underwent an eye examination by bio-microscope and indirect ophthalmoscope to check for any signs of DR through dilated pupils by + 78 lens. Participants were also interviewed and examined to determine their demographic characteristics, medical conditions and the regularity of their eye visits.</p> <p>Results</p> <p>Among 7989 screened patients, 759 (9.5%) had diabetes. Of them, 639 patients (84.2%) underwent eye examination. Five patients (0.7%) with media opacity were excluded. Of 634 examined patients with diabetes, 240 had some degree of diabetic retinopathy, and the overall standardized prevalence of any retinopathy was 37.0% (95% CI: 33.2-40.8), including 27.3% (95% CI: 23.7-30.8) (n = 175) with non-proliferative and 9.6% (95% CI: 7.3-11.9) (n = 65) with proliferative diabetic retinopathy. Clinically significant macular edema and vision-threatening retinopathy were detected in 5.8% (95% CI: 4.0-7.7) (n = 38) and 14.0% (95% CI: 11.3-16.7) (n = 95) of patients, respectively. Only 143 patients (22.6%) with diabetes had a history of regular eye examination.</p> <p>Conclusion</p> <p>This study demonstrated a high prevalence and poor control of DR in Tehran province. This suggests the need for adequate prevention and treatment in patients with diabetes.</p

In vivo and in silico determination of essential genes of Campylobacter jejuni

<p>Abstract</p> <p>Background</p> <p>In the United Kingdom, the thermophilic <it>Campylobacter </it>species <it>C. jejuni </it>and <it>C. coli </it>are the most frequent causes of food-borne gastroenteritis in humans. While campylobacteriosis is usually a relatively mild infection, it has a significant public health and economic impact, and possible complications include reactive arthritis and the autoimmune diseases Guillain-Barré syndrome. The rapid developments in "omics" technologies have resulted in the availability of diverse datasets allowing predictions of metabolism and physiology of pathogenic micro-organisms. When combined, these datasets may allow for the identification of potential weaknesses that can be used for development of new antimicrobials to reduce or eliminate <it>C. jejuni </it>and <it>C. coli </it>from the food chain.</p> <p>Results</p> <p>A metabolic model of <it>C. jejuni </it>was constructed using the annotation of the NCTC 11168 genome sequence, a published model of the related bacterium <it>Helicobacter pylori</it>, and extensive literature mining. Using this model, we have used <it>in silico </it>Flux Balance Analysis (FBA) to determine key metabolic routes that are essential for generating energy and biomass, thus creating a list of genes potentially essential for growth under laboratory conditions. To complement this <it>in silico </it>approach, candidate essential genes have been determined using a whole genome transposon mutagenesis method. FBA and transposon mutagenesis (both this study and a published study) predict a similar number of essential genes (around 200). The analysis of the intersection between the three approaches highlights the shikimate pathway where genes are predicted to be essential by one or more method, and tend to be network hubs, based on a previously published <it>Campylobacter </it>protein-protein interaction network, and could therefore be targets for novel antimicrobial therapy.</p> <p>Conclusions</p> <p>We have constructed the first curated metabolic model for the food-borne pathogen <it>Campylobacter jejuni </it>and have presented the resulting metabolic insights. We have shown that the combination of <it>in silico </it>and <it>in vivo </it>approaches could point to non-redundant, indispensable genes associated with the well characterised shikimate pathway, and also genes of unknown function specific to <it>C. jejuni</it>, which are all potential novel <it>Campylobacter </it>intervention targets.</p

Three-dimensional bio-printing and bone tissue engineering: technical innovations and potential applications in maxillofacial reconstructive surgery

Background Bone grafting has been considered the gold standard for hard tissue reconstructive surgery and is widely used for large mandibular defect reconstruction. However, the midface encompasses delicate structures that are surrounded by a complex bone architecture, which makes bone grafting using traditional methods very challenging. Three-dimensional (3D) bioprinting is a developing technology that is derived from the evolution of additive manufacturing. It enables precise development of a scaffold from different available biomaterials that mimic the shape, size, and dimension of a defect without relying only on the surgeon’s skills and capabilities, and subsequently, may enhance surgical outcomes and, in turn, patient satisfaction and quality of life. Review This review summarizes different biomaterial classes that can be used in 3D bioprinters as bioinks to fabricate bone scaffolds, including polymers, bioceramics, and composites. It also describes the advantages and limitations of the three currently used 3D bioprinting technologies: inkjet bioprinting, micro-extrusion, and laser-assisted bioprinting. Conclusions Although 3D bioprinting technology is still in its infancy and requires further development and optimization both in biomaterials and techniques, it offers great promise and potential for facial reconstruction with improved outcome

Global, regional, and national age-sex-specific mortality and life expectancy, 1950-2017 : a systematic analysis for the Global Burden of Disease Study 2017

Background Assessments of age-specific mortality and life expectancy have been done by the UN Population Division, Department of Economics and Social Affairs (UNPOP), the United States Census Bureau, WHO, and as part of previous iterations of the Global Burden of Diseases, Injuries, and Risk Factors Study (GBD). Previous iterations of the GBD used population estimates from UNPOP, which were not derived in a way that was internally consistent with the estimates of the numbers of deaths in the GBD. The present iteration of the GBD, GBD 2017, improves on previous assessments and provides timely estimates of the mortality experience of populations globally. Methods The GBD uses all available data to produce estimates of mortality rates between 1950 and 2017 for 23 age groups, both sexes, and 918 locations, including 195 countries and territories and subnational locations for 16 countries. Data used include vital registration systetns, sample registration systetns, household surveys (complete birth histories, summary birth histories, sibling histories), censuses (summary birth histories, household deaths), and Demographic Surveillance Sites. In total, this analysis used 8259 data sources. Estimates of the probability of death between birth and the age of 5 years and between ages 15 and 60 years are generated and then input into a model life table system to produce complete life tables for all locations and years. Fatal discontinuities and mortality due to HIV/AIDS are analysed separately and then incorporated into the estimation. We analyse the relationship between age-specific mortality and development status using the Socio-demographic Index, a composite measure based on fertility under the age of 25 years, education, and income. There are four main methodological improvements in GBD 2017 compared with GBD 2016: 622 additional data sources have been incorporated; new estimates of population, generated by the GBD study, are used; statistical methods used in different components of the analysis have been further standardised and improved; and the analysis has been extended backwards in time by two decades to start in 1950. Findings Globally, 18.7% (95% uncertainty interval 18.4-19.0) of deaths were registered in 1950 and that proportion has been steadily increasing since, with 58.8% (58.2-59.3) of all deaths being registered in 2015. At the global level, between 1950 and 2017, life expectancy increased from 48.1 years (46.5-49.6) to 70.5 years (70.1-70.8) for men and from 52.9 years (51.7-54.0) to 75.6 years (75.3-75.9) for women. Despite this overall progress, there remains substantial variation in life expectancy at birth in 2017, which ranges from 49.1 years (46.5-51.7) for men in the Central African Republic to 87.6 years (86.9-88.1) among women in Singapore. The greatest progress across age groups was for children younger than 5 years; under-5 mortality dropped from 216.0 deaths (196.3-238.1) per 1000 livebirths in 1950 to 38.9 deaths (35.6-42.83) per 1000 livebirths in 2017, with huge reductions across countries. Nevertheless, there were still 5.4 million (5.2-5.6) deaths among children younger than 5 years in the world in 2017. Progress has been less pronounced and more variable for adults, especially for adult tnales, who had stagnant or increasing mortality rates in several countries. The gap between male and female life expectancy between 1950 and 2017, while relatively stable at the global level, shows distinctive patterns across super-regions and has consistently been the largest in central Europe, eastern Europe, and central Asia, and smallest in south Asia. Performance was also variable across countries and time in observed mortality rates compared with those expected on the basis of development. Interpretation This analysis of age-sex-specific mortality shows that there are remarkably complex patterns in population mortality across countries. The findings of this study highlight global successes, such as the large decline in under-5 mortality, which reflects significant local, national, and global commitment and investment over several decades. However, they also bring attention to mortality patterns that are a cause for concern, particularly among adult men and, to a lesser extent, wotnen, whose mortality rates have stagnated in many countries over the time period of this study, and in some cases are increasing. Copyright C) 2018 The Author(s). Published by Elsevier Ltd.Peer reviewe