Collaborative Indoor Positioning Systems: A Systematic Review

Research and development in Collaborative Indoor Positioning Systems (CIPSs) is growing steadily due to their potential to improve on the performance of their non-collaborative counterparts. In contrast to the outdoors scenario, where Global Navigation Satellite System is widely adopted, in (collaborative) indoor positioning systems a large variety of technologies, techniques, and methods is being used. Moreover, the diversity of evaluation procedures and scenarios hinders a direct comparison. This paper presents a systematic review that gives a general view of the current CIPSs. A total of 84 works, published between 2006 and 2020, have been identified. These articles were analyzed and classified according to the described system’s architecture, infrastructure, technologies, techniques, methods, and evaluation. The results indicate a growing interest in collaborative positioning, and the trend tend to be towards the use of distributed architectures and infrastructure-less systems. Moreover, the most used technologies to determine the collaborative positioning between users are wireless communication technologies (Wi-Fi, Ultra-WideBand, and Bluetooth). The predominant collaborative positioning techniques are Received Signal Strength Indication, Fingerprinting, and Time of Arrival/Flight, and the collaborative methods are particle filters, Belief Propagation, Extended Kalman Filter, and Least Squares. Simulations are used as the main evaluation procedure. On the basis of the analysis and results, several promising future research avenues and gaps in research were identified

An autonomous ultra-wide band-based attitude and position determination technique for indoor mobile laser scanning

Mobile laser scanning (MLS) has been widely used in three-dimensional (3D) city modelling data collection, such as Google cars for Google Map/Earth. Building Information Modelling (BIM) has recently emerged and become prominent. 3D models of buildings are essential for BIM. Static laser scanning is usually used to generate 3D models for BIM, but this method is inefficient if a building is very large, or it has many turns and narrow corridors. This paper proposes using MLS for BIM 3D data collection. The positions and attitudes of the mobile laser scanner are important for the correct georeferencing of the 3D models. This paper proposes using three high-precision ultra-wide band (UWB) tags to determine the positions and attitudes of the mobile laser scanner. The accuracy of UWB-based MLS 3D models is assessed by comparing the coordinates of target points, as measured by static laser scanning and a total station survey

A Review of Radio Frequency Based Localization for Aerial and Ground Robots with 5G Future Perspectives

Efficient localization plays a vital role in many modern applications of Unmanned Ground Vehicles (UGV) and Unmanned aerial vehicles (UAVs), which would contribute to improved control, safety, power economy, etc. The ubiquitous 5G NR (New Radio) cellular network will provide new opportunities for enhancing localization of UAVs and UGVs. In this paper, we review the radio frequency (RF) based approaches for localization. We review the RF features that can be utilized for localization and investigate the current methods suitable for Unmanned vehicles under two general categories: range-based and fingerprinting. The existing state-of-the-art literature on RF-based localization for both UAVs and UGVs is examined, and the envisioned 5G NR for localization enhancement, and the future research direction are explored

Review of UAV positioning in indoor environments and new proposal based on US measurements

Este documento se considera que es una ponencia de congresos en lugar de un capítulo de libro.10th International Conference on Indoor Positioning and Indoor Navigation (IPIN 2019) Pisa, Italy, September 30th - October 3rd, 2019The use of unmanned aerial vehicles (UAVs) has increased dramatically in recent years because of their huge potential in both civil and military applications and the decrease in prize of UAVs products. Location detection can be implemented through GNSS technology in outdoor environments, nevertheless its accuracy could be insufficient for some applications. Usability of GNSS in indoor environments is limited due to the signal attenuation as it cross through walls or the absence of line of sight. Considering the big market opportunity of indoor UAVs many researchers are devoting their efforts in the exploration of solutions for their positioning. Indoor UAV applications include location based services (LBS), advertisement, ambient assisted living environments or emergency response. This work is an update survey in UAV indoor localization, so it can provide a guide and technical comparison perspective of different technologies with their main advantages and drawbacks. Finally, we propose an approach based on an ultrasonic local positioning system.Universidad de AlcaláJunta de Comunidades de Castilla-La ManchaMinisterio de Economía, Industria y Competitivida

A Review of pedestrian indoor positioning systems for mass market applications

In the last decade, the interest in Indoor Location Based Services (ILBS) has increased stimulating the development of Indoor Positioning Systems (IPS). In particular, ILBS look for positioning systems that can be applied anywhere in the world for millions of users, that is, there is a need for developing IPS for mass market applications. Those systems must provide accurate position estimations with minimum infrastructure cost and easy scalability to different environments. This survey overviews the current state of the art of IPSs and classifies them in terms of the infrastructure and methodology employed. Finally, each group is reviewed analysing its advantages and disadvantages and its applicability to mass market applications

Low cost inertial-based localization system for a service robot

Dissertation presented at Faculty of Sciences and Technology of the New University of Lisbon to attain the Master degree in Electrical and Computer Science EngineeringThe knowledge of a robot’s location it’s fundamental for most part of service robots. The success of tasks such as mapping and planning depend on a good robot’s position knowledge. The main goal of this dissertation is to present a solution that provides a estimation of the robot’s location. This is, a tracking system that can run either inside buildings or outside them, not taking into account just structured environments. Therefore, the localization system takes into account only measurements relative. In the presented solution is used an AHRS device and digital encoders placed on wheels to make a estimation of robot’s position. It also relies on the use of Kalman Filter to integrate sensorial information and deal with estimate errors. The developed system was testes in real environments through its integration on real robot. The results revealed that is not possible to attain a good position estimation using only low-cost inertial sensors. Thus, is required the integration of more sensorial information, through absolute or relative measurements technologies, to provide a more accurate position estimation

WALLSY: The UWB and SmartMesh IP enabled Wireless Ad-hoc Low-power Localization SYstem

This paper follows the implementation of a proofof-concept localization system for GNSS-denied environments. WALLSY (Wireless Ad-hoc Low-power Localization SYstem) is a portable and modular Ultra Wide-Band (UWB) and Smart Mesh IP (SMIP) hybrid. WALLSY uses UWB two way ranging (TWR) to measure distances, which are then sent via the lowpower SMIP backbone network to a central hub for calculating coordinates of tracked objects. The system is highly flexible and requires no external infrastructure or prior knowledge of the installation site. It uses a completely nomadic topology and delivers high localization accuracy with all modules being battery powered. It achieves this by using a custom time-slotting protocol which maximizes deep-sleep mode for UWB. Battery life can be further improved by activating inertial measurement unit (IMU) filtering. Visualization of tracked objects and system reconfiguration can be executed on-the-fly and are both accessible to end users through a simple graphical user interface (GUI). Results demonstrate that WALLSY can achieve more than ten times longer battery lifetime compared to competing solutions (localizing every 30 seconds). It provides 3D coordinates with an average spatial error of 60.5cm and an average standard deviation of 15cm. The system also provides support for up to 20 tags

Identification and Mitigation of NLOS based on Channel Information Rules for Indoor UWB Localization

Indoor localization is an emerging technology that can be utilized for developing products and services for commercial usage, public safety, military applications and so forth. Commercially it can be applied to track children, people with special needs, help navigate blind people, locate equipment, mobile robots, etc. The objective of this thesis is to enable an indoor mobile vehicle to determine its location and thereby making it capable of autonomous localization under Non-light of sight (NLOS) conditions. The solution developed is based on Ultra Wideband (UWB) based Indoor Positioning System (IPS) in the building. The proposed method increases robustness, scalability, and accuracy of location. The out of the box system of DecaWave TREK1000 provides tag tracking features but has no method to detect and mitigate location inaccuracies due to the multipath effect from physical obstacles found in an indoor environment. This NLOS condition causes ranges to be positively biased, hence the wrong location is reported. Our approach to deal with the NLOS problem is based on the use of Rules Classifier, which is based on channel information. Once better range readings are achieved, approximate location is calculated based on Time of Flight (TOF). Moreover, the proposed rule based IPS can be easily implemented on hardware due to the low complexity. The measurement results, which was obtained using the proposed mitigation algorithm, show considerable improvements in the accuracy of the location estimation which can be used in different IPS applications requiring centimeter level precision. The performance of the proposed algorithm is evaluated experimentally using an indoor positioning platform in a laboratory environment, and is shown to be significantly better than conventional approaches. The maximum positioning error is reduced to 15 cm for NLOS using both an offline and real time tracking algorithm extended from the proposed approach