Pseudo-functional testing: bridging the gap between manufacturing test and functional operation.

Yuan, Feng.Thesis (M.Phil.)--Chinese University of Hong Kong, 2009.Includes bibliographical references (leaves 60-65).Abstract also in Chinese.Abstract --- p.iAcknowledgement --- p.iiChapter 1 --- Introduction --- p.1Chapter 1.1 --- Manufacturing Test --- p.1Chapter 1.1.1 --- Functional Testing vs. Structural Testing --- p.2Chapter 1.1.2 --- Fault Model --- p.3Chapter 1.1.3 --- Automatic Test Pattern Generation --- p.4Chapter 1.1.4 --- Design for Testability --- p.6Chapter 1.2 --- Pseudo-Functional Manufacturing Test --- p.13Chapter 1.3 --- Thesis Motivation and Organization --- p.16Chapter 2 --- On Systematic Illegal State Identification --- p.19Chapter 2.1 --- Introduction --- p.19Chapter 2.2 --- Preliminaries and Motivation --- p.20Chapter 2.3 --- What is the Root Cause of Illegal States? --- p.22Chapter 2.4 --- Illegal State Identification Flow --- p.26Chapter 2.5 --- Justification Scheme Construction --- p.30Chapter 2.6 --- Experimental Results --- p.34Chapter 2.7 --- Conclusion --- p.35Chapter 3 --- Compression-Aware Pseudo-Functional Testing --- p.36Chapter 3.1 --- Introduction --- p.36Chapter 3.2 --- Motivation --- p.38Chapter 3.3 --- Proposed Methodology --- p.40Chapter 3.4 --- Pattern Generation in Compression-Aware Pseudo-Functional Testing --- p.42Chapter 3.4.1 --- Circuit Pre-Processing --- p.42Chapter 3.4.2 --- Pseudo-Functional Random Pattern Generation with Multi-Launch Cycles --- p.43Chapter 3.4.3 --- Compressible Test Pattern Generation for Pseudo-Functional Testing --- p.45Chapter 3.5 --- Experimental Results --- p.52Chapter 3.5.1 --- Experimental Setup --- p.52Chapter 3.5.2 --- Results and Discussion --- p.54Chapter 3.6 --- Conclusion --- p.56Chapter 4 --- Conclusion and Future Work --- p.58Bibliography --- p.6

Gbit/second lossless data compression hardware

This thesis investigates how to improve the performance of lossless data compression hardware as a tool to reduce the cost per bit stored in a computer system or transmitted over a communication network. Lossless data compression allows the exact reconstruction of the original data after decompression. Its deployment in some high-bandwidth applications has been hampered due to performance limitations in the compressing hardware that needs to match the performance of the original system to avoid becoming a bottleneck. Advancing the area of lossless data compression hardware, hence, offers a valid motivation with the potential of doubling the performance of the system that incorporates it with minimum investment. This work starts by presenting an analysis of current compression methods with the objective of identifying the factors that limit performance and also the factors that increase it. [Continues.

NASA Space Engineering Research Center for VLSI systems design

This annual review reports the center's activities and findings on very large scale integration (VLSI) systems design for 1990, including project status, financial support, publications, the NASA Space Engineering Research Center (SERC) Symposium on VLSI Design, research results, and outreach programs. Processor chips completed or under development are listed. Research results summarized include a design technique to harden complementary metal oxide semiconductors (CMOS) memory circuits against single event upset (SEU); improved circuit design procedures; and advances in computer aided design (CAD), communications, computer architectures, and reliability design. Also described is a high school teacher program that exposes teachers to the fundamentals of digital logic design

Conception et test des circuits et systèmes numériques à haute fiabilité et sécurité

Research activities I carried on after my nomination as Chargé de Recherche deal with the definition of methodologies and tools for the design, the test and the reliability of secure digital circuits and trustworthy manufacturing. More recently, we have started a new research activity on the test of 3D stacked Integrated CIrcuits, based on the use of Through Silicon Vias. Moreover, thanks to the relationships I have maintained after my post-doc in Italy, I have kept on cooperating with Politecnico di Torino on the topics related to test and reliability of memories and microprocessors.Secure and Trusted DevicesSecurity is a critical part of information and communication technologies and it is the necessary basis for obtaining confidentiality, authentication, and integrity of data. The importance of security is confirmed by the extremely high growth of the smart-card market in the last 20 years. It is reported in "Le monde Informatique" in the article "Computer Crime and Security Survey" in 2007 that financial losses due to attacks on "secure objects" in the digital world are greater than $11 Billions. Since the race among developers of these secure devices and attackers accelerates, also due to the heterogeneity of new systems and their number, the improvement of the resistance of such components becomes today’s major challenge.Concerning all the possible security threats, the vulnerability of electronic devices that implement cryptography functions (including smart cards, electronic passports) has become the Achille’s heel in the last decade. Indeed, even though recent crypto-algorithms have been proven resistant to cryptanalysis, certain fraudulent manipulations on the hardware implementing such algorithms can allow extracting confidential information. So-called Side-Channel Attacks have been the first type of attacks that target the physical device. They are based on information gathered from the physical implementation of a cryptosystem. For instance, by correlating the power consumed and the data manipulated by the device, it is possible to discover the secret encryption key. Nevertheless, this point is widely addressed and integrated circuit (IC) manufacturers have already developed different kinds of countermeasures.More recently, new threats have menaced secure devices and the security of the manufacturing process. A first issue is the trustworthiness of the manufacturing process. From one side, secure devices must assure a very high production quality in order not to leak confidential information due to a malfunctioning of the device. Therefore, possible defects due to manufacturing imperfections must be detected. This requires high-quality test procedures that rely on the use of test features that increases the controllability and the observability of inner points of the circuit. Unfortunately, this is harmful from a security point of view, and therefore the access to these test features must be protected from unauthorized users. Another harm is related to the possibility for an untrusted manufacturer to do malicious alterations to the design (for instance to bypass or to disable the security fence of the system). Nowadays, many steps of the production cycle of a circuit are outsourced. For economic reasons, the manufacturing process is often carried out by foundries located in foreign countries. The threat brought by so-called Hardware Trojan Horses, which was long considered theoretical, begins to materialize.A second issue is the hazard of faults that can appear during the circuit’s lifetime and that may affect the circuit behavior by way of soft errors or deliberate manipulations, called Fault Attacks. They can be based on the intentional modification of the circuit’s environment (e.g., applying extreme temperature, exposing the IC to radiation, X-rays, ultra-violet or visible light, or tampering with clock frequency) in such a way that the function implemented by the device generates an erroneous result. The attacker can discover secret information by comparing the erroneous result with the correct one. In-the-field detection of any failing behavior is therefore of prime interest for taking further action, such as discontinuing operation or triggering an alarm. In addition, today’s smart cards use 90nm technology and according to the various suppliers of chip, 65nm technology will be effective on the horizon 2013-2014. Since the energy required to force a transistor to switch is reduced for these new technologies, next-generation secure systems will become even more sensitive to various classes of fault attacks.Based on these considerations, within the group I work with, we have proposed new methods, architectures and tools to solve the following problems:• Test of secure devices: unfortunately, classical techniques for digital circuit testing cannot be easily used in this context. Indeed, classical testing solutions are based on the use of Design-For-Testability techniques that add hardware components to the circuit, aiming to provide full controllability and observability of internal states. Because crypto‐ processors and others cores in a secure system must pass through high‐quality test procedures to ensure that data are correctly processed, testing of crypto chips faces a dilemma. In fact design‐for‐testability schemes want to provide high controllability and observability of the device while security wants minimal controllability and observability in order to hide the secret. We have therefore proposed, form one side, the use of enhanced scan-based test techniques that exploit compaction schemes to reduce the observability of internal information while preserving the high level of testability. From the other side, we have proposed the use of Built-In Self-Test for such devices in order to avoid scan chain based test.• Reliability of secure devices: we proposed an on-line self-test architecture for hardware implementation of the Advanced Encryption Standard (AES). The solution exploits the inherent spatial replications of a parallel architecture for implementing functional redundancy at low cost.• Fault Attacks: one of the most powerful types of attack for secure devices is based on the intentional injection of faults (for instance by using a laser beam) into the system while an encryption occurs. By comparing the outputs of the circuits with and without the injection of the fault, it is possible to identify the secret key. To face this problem we have analyzed how to use error detection and correction codes as counter measure against this type of attack, and we have proposed a new code-based architecture. Moreover, we have proposed a bulk built-in current-sensor that allows detecting the presence of undesired current in the substrate of the CMOS device.• Fault simulation: to evaluate the effectiveness of countermeasures against fault attacks, we developed an open source fault simulator able to perform fault simulation for the most classical fault models as well as user-defined electrical level fault models, to accurately model the effect of laser injections on CMOS circuits.• Side-Channel attacks: they exploit physical data-related information leaking from the device (e.g. current consumption or electro-magnetic emission). One of the most intensively studied attacks is the Differential Power Analysis (DPA) that relies on the observation of the chip power fluctuations during data processing. I studied this type of attack in order to evaluate the influence of the countermeasures against fault attack on the power consumption of the device. Indeed, the introduction of countermeasures for one type of attack could lead to the insertion of some circuitry whose power consumption is related to the secret key, thus allowing another type of attack more easily. We have developed a flexible integrated simulation-based environment that allows validating a digital circuit when the device is attacked by means of this attack. All architectures we designed have been validated through this tool. Moreover, we developed a methodology that allows to drastically reduce the time required to validate countermeasures against this type of attack.TSV- based 3D Stacked Integrated Circuits TestThe stacking process of integrated circuits using TSVs (Through Silicon Via) is a promising technology that keeps the development of the integration more than Moore’s law, where TSVs enable to tightly integrate various dies in a 3D fashion. Nevertheless, 3D integrated circuits present many test challenges including the test at different levels of the 3D fabrication process: pre-, mid-, and post- bond tests. Pre-bond test targets the individual dies at wafer level, by testing not only classical logic (digital logic, IOs, RAM, etc) but also unbounded TSVs. Mid-bond test targets the test of partially assembled 3D stacks, whereas finally post-bond test targets the final circuit.The activities carried out within this topic cover 2 main issues:• Pre-bond test of TSVs: the electrical model of a TSV buried within the substrate of a CMOS circuit is a capacitance connected to ground (when the substrate is connected to ground). The main assumption is that a defect may affect the value of that capacitance. By measuring the variation of the capacitance’s value it is possible to check whether the TSV is correctly fabricated or not. We have proposed a method to measure the value of the capacitance based on the charge/ discharge delay of the RC network containing the TSV.• Test infrastructures for 3D stacked Integrated Circuits: testing a die before stacking to another die introduces the problem of a dynamic test infrastructure, where test data must be routed to a specific die based on the reached fabrication step. New solutions are proposed in literature that allow reconfiguring the test paths within the circuit, based on on-the-fly requirements. We have started working on an extension of the IEEE P1687 test standard that makes use of an automatic die-detection based on pull-up resistors.Memory and Microprocessor Test and ReliabilityThanks to device shrinking and miniaturization of fabrication technology, performances of microprocessors and of memories have grown of more than 5 magnitude order in the last 30 years. With this technology trend, it is necessary to face new problems and challenges, such as reliability, transient errors, variability and aging.In the last five years I’ve worked in cooperation with the Testgroup of Politecnico di Torino (Italy) to propose a new method to on-line validate the correctness of the program execution of a microprocessor. The main idea is to monitor a small set of control signals of the processors in order to identify incorrect activation sequences. This approach can detect both permanent and transient errors of the internal logic of the processor.Concerning the test of memories, we have proposed a new approach to automatically generate test programs starting from a functional description of the possible faults in the memory.Moreover, we proposed a new methodology, based on microprocessor error probability profiling, that aims at estimating fault injection results without the need of a typical fault injection setup. The proposed methodology is based on two main ideas: a one-time fault-injection analysis of the microprocessor architecture to characterize the probability of successful execution of each of its instructions in presence of a soft-error, and a static and very fast analysis of the control and data flow of the target software application to compute its probability of success

フィールドにおけるテスト印加と低電力論理BISTに関する研究

Advances in semiconductor process technology have resulted in various aging issues in field operation of Very Large Scale Integration (VLSI) circuits. For example, HCI (Hot carrier injection), BTI (Bias Temperature Instability), TDDB (Time Dependent Dielectric Breakdown) are well-known aging phenomena, and they can increase the circuit delay resulting in serious reliability problems. In order to avoid system failures caused by aging, recent design usually sets a certain timing margin in operational frequency of the circuit. However, it is difficult to determine the size of the proper timing margin because of the difficulty of prediction of its aging speed in actual use that is related to operational environment. Pessimistic prediction may result in performance sacrificing although it will improve the reliability of the system. BIST-based field test is a promising way to guarantee the reliability of the circuit through detecting the aging-induced faults during the circuit operation. However, the field test has a limitation on test application time, which makes it difficult to achieve high test quality. Therefore an effective test application method at field is required. In addition to the requirement of short test application time, the BIST-based field test requires performing at-speed testing in order to detect timing-related defects. However, it is well known that power dissipation during testing is much higher than that in normal circuit operation. Because excessive power dissipation causes higher IR-drop and higher temperature, it results in delay increase during testing, and in turn, causing false at-speed testing and yield loss. While many low power test methods have been proposed to tackle the test power issue, inadequate test power reduction and lower fault coverage still remain as important issues. Moreover, low power testing that just focuses on power reduction is insufficient. When the test power is reduced to a very low level, a timing-related defect may be missed by the test, and a defective circuit will appear to be a good part passing the test. Therefore, appropriate test power control is necessary though it was out of considering in the existing methods. In this dissertation, we first proposed a new test application to satisfy the limitation of short test application time for BIST-based field test, and then we proposed a new low power BIST scheme that focuses on controlling the test power to a specified value for improving the field test quality. In chapter 3, a new field test application method named “rotating test” is presented in which a set of generated test patterns to detect aging-induced faults is partitioned into several subsets, and apply each subset in one test session at field. In order to maximize the test quality for rotating test, we proposed test partitioning methods that refer to two items: First one aims at maximizing fault coverage of each subset obtained by partitioning. Second one aims at minimizing the detection time interval of all faults in rotating test to avoid system failures. Experimental results demonstrated the effectiveness of the proposed partitioning methods. In chapter 4, we proposed a new low power BIST scheme which can control the scan-in power, scan-out power and capture power while keeping test coverage at high level. In this scheme, a new circuit called pseudo low-pass filter (PLPF) is developed for scan-in power control, and a multi-cycle capture test technique is employed to reduce the capture power. In order to control scan-out power dissipated by test responses, we proposed a novel method that selects some flip-flops in scan chains at logic design phase, and fills the selected flip-flops with proper values before starting scan-shift operation so as to reduce the switching activity associated with scan-out. The experimental results for ISCAS-89 and ITC-99 benchmark circuits show that significant scan-in power reduction rate (the original rate of 50% is reduced to 7~8%) and capture power reduction rate (the original rate of 20% is reduced to 6~7%) were derived. With the scan-out controlling method, the scan-out power can be reduced from 17.2% to 8.4%, which could not be achieved by the conventional methods. Moreover, in order to control the test power to the specified rate to accommodate the various test power requirements. A scan-shift power controlling scheme was also discussed. It showed the capability of controlling any scan-shift toggle rate between 6.7% and 50%.九州工業大学博士学位論文 学位記番号:情工博甲第289号　学位授与年月日:平成26年3月25日1. INTRODUCTION|2. PRELIMINARY|3. BIST-BASED FIELD ROTATING TEST FOR AGING-INDUCED FAULT DETECTION|4. TEST POWER REDUCTION FOR LOGIC-BIST|5. SUMMARY九州工業大学平成25年

Embedded electronic systems driven by run-time reconfigurable hardware

Abstract This doctoral thesis addresses the design of embedded electronic systems based on run-time reconfigurable hardware technology –available through SRAM-based FPGA/SoC devices– aimed at contributing to enhance the life quality of the human beings. This work does research on the conception of the system architecture and the reconfiguration engine that provides to the FPGA the capability of dynamic partial reconfiguration in order to synthesize, by means of hardware/software co-design, a given application partitioned in processing tasks which are multiplexed in time and space, optimizing thus its physical implementation –silicon area, processing time, complexity, flexibility, functional density, cost and power consumption– in comparison with other alternatives based on static hardware (MCU, DSP, GPU, ASSP, ASIC, etc.). The design flow of such technology is evaluated through the prototyping of several engineering applications (control systems, mathematical coprocessors, complex image processors, etc.), showing a high enough level of maturity for its exploitation in the industry.Resumen Esta tesis doctoral abarca el diseño de sistemas electrónicos embebidos basados en tecnología hardware dinámicamente reconfigurable –disponible a través de dispositivos lógicos programables SRAM FPGA/SoC– que contribuyan a la mejora de la calidad de vida de la sociedad. Se investiga la arquitectura del sistema y del motor de reconfiguración que proporcione a la FPGA la capacidad de reconfiguración dinámica parcial de sus recursos programables, con objeto de sintetizar, mediante codiseño hardware/software, una determinada aplicación particionada en tareas multiplexadas en tiempo y en espacio, optimizando así su implementación física –área de silicio, tiempo de procesado, complejidad, flexibilidad, densidad funcional, coste y potencia disipada– comparada con otras alternativas basadas en hardware estático (MCU, DSP, GPU, ASSP, ASIC, etc.). Se evalúa el flujo de diseño de dicha tecnología a través del prototipado de varias aplicaciones de ingeniería (sistemas de control, coprocesadores aritméticos, procesadores de imagen, etc.), evidenciando un nivel de madurez viable ya para su explotación en la industria.Resum Aquesta tesi doctoral està orientada al disseny de sistemes electrònics empotrats basats en tecnologia hardware dinàmicament reconfigurable –disponible mitjançant dispositius lògics programables SRAM FPGA/SoC– que contribueixin a la millora de la qualitat de vida de la societat. S’investiga l’arquitectura del sistema i del motor de reconfiguració que proporcioni a la FPGA la capacitat de reconfiguració dinàmica parcial dels seus recursos programables, amb l’objectiu de sintetitzar, mitjançant codisseny hardware/software, una determinada aplicació particionada en tasques multiplexades en temps i en espai, optimizant així la seva implementació física –àrea de silici, temps de processat, complexitat, flexibilitat, densitat funcional, cost i potència dissipada– comparada amb altres alternatives basades en hardware estàtic (MCU, DSP, GPU, ASSP, ASIC, etc.). S’evalúa el fluxe de disseny d’aquesta tecnologia a través del prototipat de varies aplicacions d’enginyeria (sistemes de control, coprocessadors aritmètics, processadors d’imatge, etc.), demostrant un nivell de maduresa viable ja per a la seva explotació a la indústria

Optimising and evaluating designs for reconfigurable hardware

Growing demand for computational performance, and the rising cost for chip design and manufacturing make reconfigurable hardware increasingly attractive for digital system implementation. Reconfigurable hardware, such as field-programmable gate arrays (FPGAs), can deliver performance through parallelism while also providing flexibility to enable application builders to reconfigure them. However, reconfigurable systems, particularly those involving run-time reconfiguration, are often developed in an ad-hoc manner. Such an approach usually results in low designer productivity and can lead to inefficient designs. This thesis covers three main achievements that address this situation. The first achievement is a model that captures design parameters of reconfigurable hardware and performance parameters of a given application domain. This model supports optimisations for several design metrics such as performance, area, and power consumption. The second achievement is a technique that enhances the relocatability of bitstreams for reconfigurable devices, taking into account heterogeneous resources. This method increases the flexibility of modules represented by these bitstreams while reducing configuration storage size and design compilation time. The third achievement is a technique to characterise the power consumption of FPGAs in different activity modes. This technique includes the evaluation of standby power and dedicated low-power modes, which are crucial in meeting the requirements for battery-based mobile devices

The Fifth NASA Symposium on VLSI Design

The fifth annual NASA Symposium on VLSI Design had 13 sessions including Radiation Effects, Architectures, Mixed Signal, Design Techniques, Fault Testing, Synthesis, Signal Processing, and other Featured Presentations. The symposium provides insights into developments in VLSI and digital systems which can be used to increase data systems performance. The presentations share insights into next generation advances that will serve as a basis for future VLSI design