Accurate Measurement of Dynamic on-State Resistances of GaN Devices under Reverse and Forward Conduction in High Frequency Power Converter

Because of trapped charges in GaN transistor structure, device dynamic ON-state resistance RDSon is increased when it is operated in high frequency switched power converters, in which device is possibly operated by zero voltage switching (ZVS) to reduce its turn-ON switching losses. When GaN transistor finishes ZVS during one switching period, device has been operated under both reverse and forward conduction. Therefore its dynamic RDSon under both conduction modes needs to be carefully measured to understand device power losses. For this reason, a measurement circuit with simple structure and fast dynamic response is proposed to characterise device reverse and forward RDSon. In order to improve measurement sensitivity when device switches at high frequency, a trapezoidal current mode is proposed to measure device RDSon under almost constant current, which resolves measurement sensitivity issues caused by unavoidable measurement circuit parasitic inductance and measurement probes deskew in conventional device characterisation method by triangle current mode. Proposed measurement circuit and measurement method is then validated by first characterising a SiC-MOSFET with constant RDSon. Then, the comparison on GaN-HEMT dynamic RDSon measurement results demonstrates the improved accuracy of proposed trapezoidal current mode over conventional triangle current mode when device switches at 1MHz

Analysis of an On-Line Stability Monitoring Approach for DC Microgrid Power Converters

An online approach to evaluate and monitor the stability margins of dc microgrid power converters is presented in this paper. The discussed online stability monitoring technique is based on the Middlebrook's loop-gain measurement technique, adapted to the digitally controlled power converters. In this approach, a perturbation is injected into a specific digital control loop of the converter and after measuring the loop gain, its crossover frequency and phase margin are continuously evaluated and monitored. The complete analytical derivation of the model, as well as detailed design aspects, are reported. In addition, the presence of multiple power converters connected to the same dc bus, all having the stability monitoring unit, is also investigated. An experimental microgrid prototype is implemented and considered to validate the theoretical analysis and simulation results, and to evaluate the effectiveness of the digital implementation of the technique for different control loops. The obtained results confirm the expected performance of the stability monitoring tool in steady-state and transient operating conditions. The proposed method can be extended to generic control loops in power converters operating in dc microgrids

ASDTIC control and standardized interface circuits applied to buck, parallel and buck-boost dc to dc power converters

Versatile standardized pulse modulation nondissipatively regulated control signal processing circuits were applied to three most commonly used dc to dc power converter configurations: (1) the series switching buck-regulator, (2) the pulse modulated parallel inverter, and (3) the buck-boost converter. The unique control concept and the commonality of control functions for all switching regulators have resulted in improved static and dynamic performance and control circuit standardization. New power-circuit technology was also applied to enhance reliability and to achieve optimum weight and efficiency

A comparative study of MPPT and voltage regulator controllers for controlling output voltage in PV applications

The demand for renewable energy sources is more and more increasing on each passing year. Since with the increasing number of the human population, the demand for energy is increasing at an alarming state. Petroleum resources are very limited and in this scenario, renewable energy sources such as solar energy proven to be a much more reliable source of energy generation through solar panel technology but getting the most power out of a solar power system is a complicated task and need advanced digital control system and high efficient algorithms. Many algorithms have been developed for the maximum power point tracking (MPPT) of solar panels. However, most of the algorithms such as artificial intelligence and expert systems need high-end computing systems, which are costly and thus not suitable for normal household utilization. In this research, Perturb and Observe (P&O) algorithm with a PI controller algorithm are selected to enhance the MPPT task over the conventional method. This algorithm needs voltage and a current sensor to sense the power parameters of the panel in real time and generate a small difference in duty cycle called perturbation and a boost converter increase or decrease the voltage level based on the PWM signals until the system reach very close to the maximum power point possible. One flaw of this algorithm is that the system never stops at a fixed power point, rather it perturbs around the maximum power range. For further tuning the maximum power point, voltage amplitude and minimize the distortion, a PI controller will be utilized in this research project. Initial results from the solar panel model using SLG-M 350 module are satisfactory. Furthermore, the model has been tested with boost converter circuit in Simulink with a constant duty cycle. Afterward proposed MPPT+PI algorithm results have been compared with simple MPPT method. It is observed that a PI controller minimize the perturbation effect of the MPPT controller largely, which results in less distorted power curves. Additionally, overall power efficiency is increased in the case of proposed MPPT+PI controller, which is 98.5% as compared to 97.8% efficiency of conventional MPPT controller

Power system security enhancement by HVDC links using a closed-loop emergency control

In recent years, guaranteeing that large-scale interconnected systems operate safely, stably and economically has become a major and emergency issue. A number of high profile blackouts caused by cascading outages have focused attention on this issue. Embedded HVDC (High Voltage Direct Current) links within a larger AC power system are known to act as a “firewall” against cascading disturbances and therefore, can effectively contribute in preventing blackouts. A good example is the 2003 blackout in USA and Canada, where the Québec grid was not affected due to its HVDC interconnection. In the literature, many works have studied the impact of HVDC on the power system stability, but very few examples exist in the area of its impact on the system security. This paper presents a control strategy for HVDC systems to increase their contribution to system security. A real-time closed-loop control scheme is used to modulate the DC power of HVDC links to alleviate AC system overloads and improve system security. Simulations carried out on a simplified model of the Hydro-Québec network show that the proposed method works well and can greatly improve system security during emergency situations.Peer reviewedFinal Accepted Versio

Measurements, Models, Systems and Design

531 s.

Impedance-compensated grid synchronisation for extending the stability range of weak grids with voltage source converters

This paper demonstrates how the range of stable power transfer in weak grids with voltage source converters (VSCs) can be extended by modifying the grid synchronisation mechanism of a conventional synchronous reference frame phase locked loop (PLL). By introducing an impedance-conditioning term in the PLL, the VSC control system can be virtually synchronised to a stronger point in the grid to counteract the instability effects caused by high grid impedance. To verify the effectiveness of the proposed approach, the maximum static power transfer capability and the small-signal stability range of a system with a VSC HVDC terminal connected to a weak grid are calculated from an analytical model with different levels of impedance-conditioning in the PLL. Such calculations are presented for two different configurations of the VSC control system, showing how both the static power transfer capability and the small-signal stability range can be significantly improved. The validity of the stability assessment is verified by time-domain simulations in the Matlab/Simulink environment.Peer ReviewedPostprint (published version

Efficient DSP and Circuit Architectures for Massive MIMO: State-of-the-Art and Future Directions

Massive MIMO is a compelling wireless access concept that relies on the use of an excess number of base-station antennas, relative to the number of active terminals. This technology is a main component of 5G New Radio (NR) and addresses all important requirements of future wireless standards: a great capacity increase, the support of many simultaneous users, and improvement in energy efficiency. Massive MIMO requires the simultaneous processing of signals from many antenna chains, and computational operations on large matrices. The complexity of the digital processing has been viewed as a fundamental obstacle to the feasibility of Massive MIMO in the past. Recent advances on system-algorithm-hardware co-design have led to extremely energy-efficient implementations. These exploit opportunities in deeply-scaled silicon technologies and perform partly distributed processing to cope with the bottlenecks encountered in the interconnection of many signals. For example, prototype ASIC implementations have demonstrated zero-forcing precoding in real time at a 55 mW power consumption (20 MHz bandwidth, 128 antennas, multiplexing of 8 terminals). Coarse and even error-prone digital processing in the antenna paths permits a reduction of consumption with a factor of 2 to 5. This article summarizes the fundamental technical contributions to efficient digital signal processing for Massive MIMO. The opportunities and constraints on operating on low-complexity RF and analog hardware chains are clarified. It illustrates how terminals can benefit from improved energy efficiency. The status of technology and real-life prototypes discussed. Open challenges and directions for future research are suggested.Comment: submitted to IEEE transactions on signal processin