80 research outputs found
Recommended from our members
Low-power high-speed ADC design techniques in scaled CMOS process
The power consumption of a single-channel successive approximation register (SAR) analog-to-digital (ADC) tends to linearly increase with its sampling rate (f[subscript s]), when f[subscript s] is small. However, when f[subscript s] passes a certain point for a given technology node, the ADC power P increases at much higher rate and the normalized power efficiency (P/f[subscript s]) starts to degrade rapidly. To enhance the conversion speed of SAR ADC, while maintaining a good power efficiency, this thesis presents speed-enhancing techniques for SAR ADC in nano-scale CMOS technologies. First chapter presents a 2b/cycle hybrid SAR architecture with only 1 differential capacitor-DAC (CDAC). Unlike prior multi-bit/cycle SAR works that make use of only the DAC differential mode (DM) voltage, the proposed architecture exploits both the DM and the common mode (CM). By using two degrees of freedom, 2b/cycle conversion technique can boost the f[subscript s] of the ADC without any additional DAC arrays. High-speed ADCs can boost the conversion speed not only by increasing the f[subscript s] of a single-channel ADC, but also by time-interleaving multiple ADC sub-channels running at a lower rate. For an N-channel time-interleaved (TI) SAR ADC operating at f[subscript s], each sub-SAR channel only needs to operate at f[subscript s]=N. Therefore, each sub-SAR can operate in the linear power versus speed region, leading to a significant power saving compared to a single-channel ADC running at the same sampling rate. Despite of its power efficiency, TI-ADC suffers from mismatches among sub-ADC channels, including gain, offset, and timing mismatches. Among them, timing skew is one of the most difficult errors to calibrate as it is nontrivial to extract and its induced error depends on both the frequency and the amplitude of the input signal. Second chapter of this thesis presents a TI-SAR with a fast variance-based timing-skew calibration technique. It uses a single-comparator based window detector (WD) to calibrate the timing skew. The WD suppresses variance estimation errors and allow precise variance estimation from a significantly small number of samples. It has low-hardware cost and orders of magnitude faster convergence speed compared to prior variance-based timing-skew calibration technique. The last chapter presents another TI-SAR with mean absolute deviation (MAD) based timing-skew calibration technique. In addition to all the advantages presented with the fast variance-based timing-skew calibration technique, the proposed technique further reduces the digital computation power by 50% by eliminating the squaring operations, which are essential in variance-based calibration techniqueElectrical and Computer Engineerin
Recommended from our members
Design Techniques for High-Performance SAR A/D Converters
The design of electronics needs to account for the non-ideal characteristics of the device technologies used to realize practical circuits. This is particularly important in mixed analog-digital design since the best device technologies are very different for digital compared to analog circuits. One solution for this problem is to use a calibration correction approach to remove the errors introduced by devices, but this adds complexity and power dissipation, as well as reducing operation speed, and so must be optimised. This thesis addresses such an approach to improve the performance of certain types of analog-to-digital converter (ADC) used in advanced telecommunications, where speed, accuracy and power dissipation currently limit applications. The thesis specifically focuses on the design of compensation circuits for use in successive approximation register (SAR) ADCs.
ADCs are crucial building blocks in communication systems, in general, and for mobile networks, in particular. The recently launched fifth generation of mobile networks (5G) has required new ADC circuit techniques to meet the higher speed and lower power dissipation requirements for 5G technology. The SAR has become one of the most favoured architectures for designing high-performance ADCs, but the successive nature of the circuit operation makes it difficult to reach ∼GS/s sampling rates at reasonable power consumption.
Here, two calibration techniques for high-performance SAR ADCs are presented. The first uses an on-chip stochastic-based mismatch calibration technique that is able to accurately compute and compensate for the mismatch of a capacitive DAC in a SAR ADC. The stochastic nature of the proposed calibration method enables determination of the mismatch of the CAPDAC with a resolution much better than that of the DAC. This allows the unit capacitor to scale down to as low as 280aF for a 9-bit DAC. Since the CAP-DAC causes a large part of the overall dynamic power consumption and directly determines both the sizes of the driving and sampling switches and the size of the input capacitive load of the ADC and the kT/C noise power, a small CAP-DAC helps the power efficiency. To validate the proposed calibration idea, a 10-bit asynchronous SAR ADC was fabricated in 28-nm CMOS. Measurement results show that the proposed stochastic calibration improves the ADC’s SFDR and SNDR by 14.9 dB, 11.5 dB, respectively. After calibration, the fabricated SAR ADC achieves an ENOB of 9.14 bit at a sampling rate of 85 MS/s, resulting in a Walden FoM of 10.9 fJ/c-s.
The second calibration technique is a timing-skew calibration for a time-interleaved (TI) SAR ADC that calibrates/computes the inter-channel timing and offset mismatch simultaneously. Simulation results show the effectiveness of this calibration method. When used together, the proposed mismatch calibration technique and the timing-skew
calibration technique enables a TI SAR ADC to be designed that can achieve a sampling rate of ∼GS/s with 10-bit resolution and a power consumption as low as ∼10mW; specifications that satisfy the requirements of 5G technology
Energy-efficient analog-to-digital conversion for ultra-wideband radio
Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2007.Includes bibliographical references (p. 207-222).In energy constrained signal processing and communication systems, a focus on the analog or digital circuits in isolation cannot achieve the minimum power consumption. Furthermore, in advanced technologies with significant variation, yield is traditionally achieved only through conservative design and a sacrifice of energy efficiency. In this thesis, these limitations are addressed with both a comprehensive mixed-signal design methodology and new circuits and architectures, as presented in the context of an analog-to-digital converter (ADC) for ultra-wideband (UWB) radio. UWB is an emerging technology capable of high-data-rate wireless communication and precise locationing, and it requires high-speed (>500MS/s), low-resolution ADCs. The successive approximation register (SAR) topology exhibits significantly reduced complexity compared to the traditional flash architecture. Three time-interleaved SAR ADCs have been implemented. At the mixed-signal optimum energy point, parallelism and reduced voltage supplies provide more than 3x energy savings. Custom control logic, a new capacitive DAC, and a hierarchical sampling network enable the high-speed operation. Finally, only a small amount of redundancy, with negligible power penalty, dramatically improves the yield of the highly parallel ADC in deep sub-micron CMOS.by Brian P. Ginsburg.Ph.D
Fully Digital On-Chip Wideband Background Calibration for Channel Mismatches in Time-Interleaved Time-Based ADCs
This letter presents a fully integrated on-chip digital mismatch compensation system for time-based time-interleaved (TI) data converters. The proposed digital compensation features blind calibration of gain, offset, and timing mismatches. The implemented system uses time-based sampling clock mismatch detection, achieving convergence within 32K samples, which is on par with analog-assisted background methods. A specialized filter structure compensates for timing mismatches of magnitude up to 0.21 of the sampling period, nearly triple the range of other published digital compensation methods, and is effective for input signals up to 0.92 Nyquist bandwidth. The on-chip digital correction achieves suppression of all mismatch tones to levels below −60 dBc while running fully in the background. The operation is demonstrated with an 8× TI 2-GS/s analog-to-digital converter (ADC) prototype chip implemented in a 28-nm CMOS process.publishedVersionPeer reviewe
Design of Energy-Efficient A/D Converters with Partial Embedded Equalization for High-Speed Wireline Receiver Applications
As the data rates of wireline communication links increases, channel impairments such as skin effect, dielectric loss, fiber dispersion, reflections and cross-talk become more pronounced. This warrants more interest in analog-to-digital converter (ADC)-based serial link receivers, as they allow for more complex and flexible back-end digital signal processing (DSP) relative to binary or mixed-signal receivers. Utilizing this back-end DSP allows for complex digital equalization and more bandwidth-efficient modulation schemes, while also displaying reduced process/voltage/temperature (PVT) sensitivity. Furthermore, these architectures offer straightforward design translation and can directly leverage the area and power scaling offered by new CMOS technology nodes. However, the power consumption of the ADC front-end and subsequent digital signal processing is a major issue. Embedding partial equalization inside the front-end ADC can potentially result in lowering the complexity of back-end DSP and/or decreasing the ADC resolution requirement, which results in a more energy-effcient receiver. This dissertation presents efficient implementations for multi-GS/s time-interleaved ADCs with partial embedded equalization. First prototype details a 6b 1.6GS/s ADC with a novel embedded redundant-cycle 1-tap DFE structure in 90nm CMOS. The other two prototypes explain more complex 6b 10GS/s ADCs with efficiently embedded feed-forward equalization (FFE) and decision feedback equalization (DFE) in 65nm CMOS. Leveraging a time-interleaved successive approximation ADC architecture, new structures for embedded DFE and FFE are proposed with low power/area overhead. Measurement results over FR4 channels verify the effectiveness of proposed embedded equalization schemes. The comparison of fabricated prototypes against state-of-the-art general-purpose ADCs at similar speed/resolution range shows comparable performances, while the proposed architectures include embedded equalization as well
Compensation numérique pour convertisseur large bande hautement parallélisé.
Time-interleaved analog-to-digital converters (TIADC) seem to be the holy grail of analog-to-digital conversion. Theoretically, their sampling speed can be increased, very simply, by duplicating the sub-converters. The real world is different because mismatches between the converters strongly reduce the TIADC performance, especially when trying to push forward the sampling speed, or the resolution of the converter. Using background digital mismatch calibration can alleviate this limitation. The first part of the thesis is dedicated to studying the sources and effects of mismatches in a TIADC. Performance metrics such as the SNDR and the SFDR are derived as a function of the mismatch levels. In the second part, new background digital mismatch calibration techniques are presented. They are able to reduce the offset, gain, skew and bandwidth mismatch errors. The mismatches are estimated by using the statistical properties of the input signal and digital filters are used to reconstruct the correct output samples. In the third part, a 1.6 GS/s TIADC circuit, implementing offset, gain and skew mismatch calibration, demonstrates a reduction of the mismatch spurs down to a level of -70 dBFS, up to an input frequency of 750 MHz. The circuit achieves the lowest level of mismatches among TIADCs in the same frequency range, with a reasonable power and area, in spite of the overhead caused by the calibration.Les convertisseurs analogique-numérique à entrelacement temporel (TIADC) semblent être une solution prometteuse dans le monde de la conversion analogique-numérique. Leur fréquence d’échantillonnage peut théoriquement être augmentée en augmentant le nombre de convertisseurs en parallèle. En réalité, des désappariements entre les convertisseurs peuvent fortement dégrader les performances, particulièrement à haute fréquence d’échantillonnage ou à haute résolution. Ces défauts d’appariement peuvent être réduits en utilisant des techniques de calibration en arrière-plan. La première partie de cette thèse est consacrée à l’étude des sources et effets des différents types de désappariements dans un TIADC. Des indicateurs de performance tels que le SNDR ou la SFDR sont exprimés en fonction du niveau des désappariements. Dans la deuxième partie, des nouvelles techniques de calibration sont proposées. Ces techniques permettent de réduire les effets des désappariements d’offset, de gain, d’instant d’échantillonnage et de bande passante. Les désappariements sont estimés en se basant sur des propriétés statistiques du signal et la reconstruction des échantillons de sortie se fait en utilisant des filtres numériques. La troisième partie démontre les performance d’un TIADC fonctionnant a une fréquence d’échantillonnage de 1.6 GE/s et comprenant les calibration d’offset, de gain et d’instant d’échantillonnage proposées. Les raies fréquentielles dues aux désappariements sont réduites à un niveau de -70dBc jusqu’à une fréquence d’entrée de 750 MHz. Ce circuit démontre une meilleure correction de désappariements que des circuits similaires récemment publiés, et ce avec une augmentation de puissance consommée et de surface relativement faible
Wideband CMOS Data Converters for Linear and Efficient mmWave Transmitters
With continuously increasing demands for wireless connectivity, higher\ua0carrier frequencies and wider bandwidths are explored. To overcome a limited transmit power at these higher carrier frequencies, multiple\ua0input multiple output (MIMO) systems, with a large number of transmitters\ua0and antennas, are used to direct the transmitted power towards\ua0the user. With a large transmitter count, each individual transmitter\ua0needs to be small and allow for tight integration with digital circuits. In\ua0addition, modern communication standards require linear transmitters,\ua0making linearity an important factor in the transmitter design.In this thesis, radio frequency digital-to-analog converter (RF-DAC)-based transmitters are explored. They shift the transition from digital\ua0to analog closer to the antennas, performing both digital-to-analog\ua0conversion and up-conversion in a single block. To reduce the need for\ua0computationally costly digital predistortion (DPD), a linear and wellbehaved\ua0RF-DAC transfer characteristic is desirable. The combination\ua0of non-overlapping local oscillator (LO) signals and an expanding segmented\ua0non-linear RF-DAC scaling is evaluated as a way to linearize\ua0the transmitter. This linearization concept has been studied both for\ua0the linearization of the RF-DAC itself and for the joint linearization of\ua0the cascaded RF-DAC-based modulator and power amplifier (PA) combination.\ua0To adapt the linearization, observation receivers are needed.\ua0In these, high-speed analog-to-digital converters (ADCs) have a central\ua0role. A high-speed ADC has been designed and evaluated to understand\ua0how concepts used to increase the sample rate affect the dynamic performance
Aika-digitaalimuunnin laajakaistaisiin aikapohjaisiin analogia-digitaalimuuntimiin
Modern deeply scaled semiconductor processes make the design of voltage-domain circuits increasingly challenging. On the contrary, the area and power consumption of digital circuits are improving with every new process node. Consequently, digital solutions are designed in place of their purely analog counterparts in applications such as analog-to-digital (A/D) conversion. Time-based analog-to-digital converters (ADC) employ digital-intensive architectures by processing analog quantities in time-domain. The quantization step of the time-based A/D-conversion is carried out by a time-to-digital converter (TDC).
A free-running ring oscillator -based TDC design is presented for use in wideband time-based ADCs. The proposed architecture aims to maximize time resolution and full-scale range, and to achieve error resilient conversion performance with minimized power and area consumptions. The time resolution is maximized by employing a high-frequency multipath ring oscillator, and the full-scale range is extended using a high-speed gray counter. The error resilience is achieved by custom sense-amplifier -based sampling flip-flops, gray coded counter and a digital error correction algorithm for counter sampling error correction. The implemented design achieves up to 9-bit effective resolution at 250 MS/s with 4.3 milliwatt power consumption.Modernien puolijohdeteknologioiden skaalautumisen seurauksena jännitetason piirien suunnittelu tulee entistä haasteellisemmaksi. Toisaalta digitaalisten piirirakenteiden pinta-ala sekä tehonkulutus pienenevät prosessikehityksen myötä. Tästä syystä digitaalisia ratkaisuja suunnitellaan vastaavien puhtaasti analogisien rakenteiden tilalle. Analogia-digitaalimuunnos (A/D-muunnos) voidaan toteuttaa jännitetason sijaan aikatasossa käyttämällä aikapohjaisia A/D-muuntimia, jotka ovat rakenteeltaan pääosin digitaalisia. Kvantisointivaihe aikapohjaisessa A/D-muuntimessa toteutetaan aika-digitaalimuuntimella.
Työ esittelee vapaasti oskilloivaan silmukkaoskillaattoriin perustuvan aika-digitaalimuuntimen, joka on suunniteltu käytettäväksi laajakaistaisessa aikapohjaisessa A/D-muuntimessa. Esitelty rakenne pyrkii maksimoimaan muuntimen aikaresoluution sekä muunnosalueen, sekä saavuttamaan virhesietoisen muunnostoiminnan minimoidulla tehon sekä pinta-alan kulutuksella. Aikaresoluutio on maksimoitu hyödyntämällä suuritaajuista monipolkuista silmukkaoskillaattoria, ja muunnosalue on maksimoitu nopealla Gray-koodi -laskuripiirillä. Muunnosprosessin virhesietoisuus on saavutettu toteuttamalla näytteistys herkillä kiikkuelementeillä, hyödyntämällä Gray-koodattua laskuria, sekä jälkiprosessoimalla laskurin näytteistetyt arvot virheenkorjausalgoritmilla. Esitelty muunnintoteutus saavuttaa 9 bitin efektiivisen resoluution 250 MS/s näytetaajuudella ja 4.3 milliwatin tehonkulutuksella
A Low-Power, Reconfigurable, Pipelined ADC with Automatic Adaptation for Implantable Bioimpedance Applications
Biomedical monitoring systems that observe various physiological parameters or electrochemical reactions typically cannot expect signals with fixed amplitude or frequency as signal properties can vary greatly even among similar biosignals. Furthermore, advancements in biomedical research have resulted in more elaborate biosignal monitoring schemes which allow the continuous acquisition of important patient information. Conventional ADCs with a fixed resolution and sampling rate are not able to adapt to signals with a wide range of variation. As a result, reconfigurable analog-to-digital converters (ADC) have become increasingly more attractive for implantable biosensor systems. These converters are able to change their operable resolution, sampling rate, or both in order convert changing signals with increased power efficiency.
Traditionally, biomedical sensing applications were limited to low frequencies. Therefore, much of the research on ADCs for biomedical applications focused on minimizing power consumption with smaller bias currents resulting in low sampling rates. However, recently bioimpedance monitoring has become more popular because of its healthcare possibilities. Bioimpedance monitoring involves injecting an AC current into a biosample and measuring the corresponding voltage drop. The frequency of the injected current greatly affects the amplitude and phase of the voltage drop as biological tissue is comprised of resistive and capacitive elements. For this reason, a full spectrum of measurements from 100 Hz to 10-100 MHz is required to gain a full understanding of the impedance. For this type of implantable biomedical application, the typical low power, low sampling rate analog-to-digital converter is insufficient. A different optimization of power and performance must be achieved.
Since SAR ADC power consumption scales heavily with sampling rate, the converters that sample fast enough to be attractive for bioimpedance monitoring do not have a figure-of-merit that is comparable to the slower converters. Therefore, an auto-adapting, reconfigurable pipelined analog-to-digital converter is proposed. The converter can operate with either 8 or 10 bits of resolution and with a sampling rate of 0.1 or 20 MS/s. Additionally, the resolution and sampling rate are automatically determined by the converter itself based on the input signal. This way, power efficiency is increased for input signals of varying frequency and amplitude
- …