Velocity-space sensitivity of the time-of-flight neutron spectrometer at JET

The velocity-space sensitivities of fast-ion diagnostics are often described by so-called weight functions. Recently, we formulated weight functions showing the velocity-space sensitivity of the often dominant beam-target part of neutron energy spectra. These weight functions for neutron emission spectrometry (NES) are independent of the particular NES diagnostic. Here we apply these NES weight functions to the time-of-flight spectrometer TOFOR at JET. By taking the instrumental response function of TOFOR into account, we calculate time-of-flight NES weight functions that enable us to directly determine the velocity-space sensitivity of a given part of a measured time-of-flight spectrum from TOFOR

On the mechanisms governing gas penetration into a tokamak plasma during a massive gas injection

A new 1D radial fluid code, IMAGINE, is used to simulate the penetration of gas into a tokamak plasma during a massive gas injection (MGI). The main result is that the gas is in general strongly braked as it reaches the plasma, due to mechanisms related to charge exchange and (to a smaller extent) recombination. As a result, only a fraction of the gas penetrates into the plasma. Also, a shock wave is created in the gas which propagates away from the plasma, braking and compressing the incoming gas. Simulation results are quantitatively consistent, at least in terms of orders of magnitude, with experimental data for a D 2 MGI into a JET Ohmic plasma. Simulations of MGI into the background plasma surrounding a runaway electron beam show that if the background electron density is too high, the gas may not penetrate, suggesting a possible explanation for the recent results of Reux et al in JET (2015 Nucl. Fusion 55 093013)

Relationship of edge localized mode burst times with divertor flux loop signal phase in JET

A phase relationship is identified between sequential edge localized modes (ELMs) occurrence times in a set of H-mode tokamak plasmas to the voltage measured in full flux azimuthal loops in the divertor region. We focus on plasmas in the Joint European Torus where a steady H-mode is sustained over several seconds, during which ELMs are observed in the Be II emission at the divertor. The ELMs analysed arise from intrinsic ELMing, in that there is no deliberate intent to control the ELMing process by external means. We use ELM timings derived from the Be II signal to perform direct time domain analysis of the full flux loop VLD2 and VLD3 signals, which provide a high cadence global measurement proportional to the voltage induced by changes in poloidal magnetic flux. Specifically, we examine how the time interval between pairs of successive ELMs is linked to the time-evolving phase of the full flux loop signals. Each ELM produces a clear early pulse in the full flux loop signals, whose peak time is used to condition our analysis. The arrival time of the following ELM, relative to this pulse, is found to fall into one of two categories: (i) prompt ELMs, which are directly paced by the initial response seen in the flux loop signals; and (ii) all other ELMs, which occur after the initial response of the full flux loop signals has decayed in amplitude. The times at which ELMs in category (ii) occur, relative to the first ELM of the pair, are clustered at times when the instantaneous phase of the full flux loop signal is close to its value at the time of the first ELM

Measurement of the top-quark mass in all-jets tt events in pp collisions at root = 7 TeV

The mass of the top quark is measured using a sample of tt¯ candidate events with at least six jets in the final state. The sample is selected from data collected with the CMS detector in pp collisions at s√=7 TeV in 2011 and corresponds to an integrated luminosity of 3.54 fb−1 . The mass is reconstructed for each event employing a kinematic fit of the jets to a tt¯ hypothesis. The top-quark mass is measured to be 173.49±0.69(stat.)±1.21(syst.) GeV. A combination with previously published measurements in other decay modes by CMS yields a mass of 173.54±0.33(stat.)±0.96(syst.) GeV

Structural phase evolution with temperature of non-conventional particles in PIM

Some inorganic natural powders may be interesting to manufacture complex shapes by powder injection moulding (PIM). However, these powders may evolve chemical and physically with temperature during the manufacturing processes, inducing blusters and geometrical irregularities, particularly loss of circularity. These imperfections were associated to gas liberation and dimensional variations during the debinding and sintering treatments and not to feedstocks' fluidity. Natural powders for manufacturing products by PIM must be previously calcined before conformation, in order to eliminate possible chemical reactions and phase transformation during debinding and sintering. To highlight the effect of the calcination process in the final quality of the sinter, a complex geometrical testing-probe was developed. After sintering, calcined and non-calcined powders have similar mechanical properties (, , Weibull modulus = 10). The use of a feedstock of the natural calcined powders leads to PIM products with high geometrical reproducibility and good surface finishing.http://www.sciencedirect.com/science/article/B6TGJ-4PG117J-5/1/0842d834adcae3de70401e61ad09751