Evaluation of Column Separation Methods for Simplification of the Wet Chemistry Approach to Isolation of 211At: Evaluation of Column Separation Methods for Simplification of the Wet Chemistry Approach to Isolation of 211At

Difficulties with reproducibility of isolation yields when distilling 211At from irradiated bismuth targets led us to use a “wet chemistry” approach for that process1. The wet chemistry approach has provided 211At isolation yields of ~ 78 % after decay and Bi attenuation corrections2. However, the use of diisopropyl ether (DIPE) in the separation process has made it difficult to reach our goal of automating the 211At isolation. Therefore, we have investigated the use of column materials to simplify the isolation of 211At and remove DIPE from the process. In this investigation we evaluated the use of a strong anion exchange resin (AG1×8), a strong cation exchange resin (AG MP-50) and a polyethylene glycol (PEG)-coated resin for separation of 211At from the bismuth target material. Anion and cation resins AG1×8 and AG MP-50 were obtained from commercial sources. A PEG-coated resin was prepared by reaction of the Merrifield resin with mPEG-OH 2000 in the pres-ence of tBuOK at 80 °C for 3 days, followed by drying under vacuum. Prior to use of the PEG resin, it was soaked in H2O. Resins (400–800 mg) were loaded into polypropylene columns (Applied Separations, Inc.). Column elution studies were conducted with and without reductants (0.75M FeSO4/1M H2SO4 or Na2S2O5) to determine their effect on capture of 211At. After target dissolution in HNO3 (and in most cases subse-quent removal of HNO3 by distillation and redis-solution of solid in 8M HCl), 211At solution was loaded onto the column, then the column was washed with 2M HCl or H2O to separate the Bi, and finally was eluted with strong base to remove the 211At. Initial studies were conducted with stable iodine to determine if reductants were effective in the presence of large amounts of bismuth ions. Studies with AG1×8 used 125I to determine if that radiohalogen could be captured and recovered from the column when eluting with boric acid buffers at pH 5.3, 8.0 or 10, or H2O at pH 7. Capture and recovery of 211At was evaluated under the same conditions. Further studies with AG1×8 involved eluting with 4M H2SO4. A limited study with AG MP-50 resin used 1M HCl as eluant. Studies with PEG-coated columns used 2M HCl, 4M HCl, 8M HCl, 16 M HNO3 and 8M HNO3 as initial (capture) eluants. Strong base (0.2, 1 or 12.5 M NaOH; 15M NH4OH) and 3 or 500 mM tetrabutylammonium bromide (TBAB) were evaluated for removal of 211At from the columns tested. The efficiency for capture of 211At on the AG1×8 column was high (99%) when loading with strong acid, but decreased when using 0.1–0.2M boric acid (69–91 %) buffer. Low 211At capture efficiencies were obtained with AG MP-50 col-umns (15–29%). High 211At capture efficiencies (96–100%) were obtained with PEG-coated resins when loading with 8M HCl or 8M HNO3, irre-spective of whether reductant was in the acid solution. Four column washings (2 mL of 2M HCl each) were required to remove all Bi prior to elution of 211At. No bismuth was detected in solution from the 4th washing in any of the elutions studied. Low (< 6%) recovery of 211At from the AG1×8 columns was obtained using the conditions studied. Good (60–79%) recovery of 211At was obtained from PEG-coated resin using 15M NH4OH. Isolation of the 211At from NH4OH solution was accomplished by distillation. In an initial study 211At distilled before obtaining a dry residue. However, later studies demonstrated that addi-tion of NaOH prior to distillation kept the 211At in the distilling flask. These studies demonstrated that PEG-coated columns could be used to isolate 211At from HNO3-dissolved bismuth targets with good non-optimized (~60%) overall recovery yields. The studies are continuing with optimization of elu-tion conditions and automation of the process

Physical characteristics of localized surface plasmons resulting from nano-scale structured multi-layer thin films deposited on D-shaped optical fiber

Novel surface plasmonic optical fiber sensors have been fabricated using multiple coatings deposited on a lapped section of a single mode fiber. UV laser irradiation processing with a phase mask produces a nano-scaled surface relief grating structure resembling nano-wires. The resulting individual corrugations produced by material compaction are approximately 20 μm long with an average width at half maximum of 100 nm and generate localized surface plasmons. Experimental data are presented that show changes in the spectral characteristics after UV processing, coupled with an overall increase in the sensitivity of the devices to surrounding refractive index. Evidence is presented that there is an optimum UV dosage (48 joules) over which no significant additional optical change is observed. The devices are characterized with regards to change in refractive index, where significantly high spectral sensitivities in the aqueous index regime are found, ranging up to 4000 nm/RIU for wavelength and 800 dB/RIU for intensity

Mechanical Strength of 17 134 Model Proteins and Cysteine Slipknots

A new theoretical survey of proteins' resistance to constant speed stretching is performed for a set of 17 134 proteins as described by a structure-based model. The proteins selected have no gaps in their structure determination and consist of no more than 250 amino acids. Our previous studies have dealt with 7510 proteins of no more than 150 amino acids. The proteins are ranked according to the strength of the resistance. Most of the predicted top-strength proteins have not yet been studied experimentally. Architectures and folds which are likely to yield large forces are identified. New types of potent force clamps are discovered. They involve disulphide bridges and, in particular, cysteine slipknots. An effective energy parameter of the model is estimated by comparing the theoretical data on characteristic forces to the corresponding experimental values combined with an extrapolation of the theoretical data to the experimental pulling speeds. These studies provide guidance for future experiments on single molecule manipulation and should lead to selection of proteins for applications. A new class of proteins, involving cystein slipknots, is identified as one that is expected to lead to the strongest force clamps known. This class is characterized through molecular dynamics simulations.Comment: 40 pages, 13 PostScript figure

A LC-MS metabolomics approach to investigate the effect of raw apple intake in the rat plasma metabolome

Fruit and vegetable consumption has been associated with several health benefits; however the mechanisms are largely unknown at the biochemical level. Our research aims to investigate whether plasma metabolome profiling can reflect biological effects after feeding rats with raw apple by using an untargeted UPLC-ESI-TOF-MS based metabolomics approach in both positive and negative mode. Eighty young male rats were randomised into groups receiving daily 0, 5 or 10 g fresh apple slices, respectively, for 13 weeks. During weeks 3-6 some of the animals were receiving 4 mg/ml 1,2-dimethylhydrazine dihydrochloride (DMH) once a week. Plasma samples were taken at the end of the intervention and among all groups, about half the animals were 12 h fasted. An initial ANOVA-simultaneous component analysis with a three-factor or two-factor design was employed in order to isolate potential metabolic variations related to the consumption of fresh apples. Partial least squares-discriminant analysis was then applied in order to select discriminative features between plasma metabolites in control versus apple fed rats and partial least squares modelling to reveal possible dose response. The findings indicate that in laboratory rats apple feeding may alter the microbial amino acid fermentation, lowering toxic metabolites from amino acids metabolism and increasing metabolism into more protective products. It may also delay lipid and amino acid catabolism, gluconeogenesis, affect other features of the transition from the postprandial to the fasting state and affect steroid metabolism by suppressing the plasma level of stress corticosteroids, certain mineralocorticoids and oxidised bile acid metabolites. Several new hypotheses regarding the cause of health effects from apple intake can be generated from this study for further testing in humans. © 2013 Springer Science+Business Media New York

Microbiome to Brain:Unravelling the Multidirectional Axes of Communication

The gut microbiome plays a crucial role in host physiology. Disruption of its community structure and function can have wide-ranging effects making it critical to understand exactly how the interactive dialogue between the host and its microbiota is regulated to maintain homeostasis. An array of multidirectional signalling molecules is clearly involved in the host-microbiome communication. This interactive signalling not only impacts the gastrointestinal tract, where the majority of microbiota resides, but also extends to affect other host systems including the brain and liver as well as the microbiome itself. Understanding the mechanistic principles of this inter-kingdom signalling is fundamental to unravelling how our supraorganism function to maintain wellbeing, subsequently opening up new avenues for microbiome manipulation to favour desirable mental health outcome

Evaluation of Column Separation Methods for Simplification of the Wet Chemistry Approach to Isolation of 211At: Evaluation of Column Separation Methods for Simplification of the Wet Chemistry Approach to Isolation of 211At

Difficulties with reproducibility of isolation yields when distilling 211At from irradiated bismuth targets led us to use a “wet chemistry” approach for that process1. The wet chemistry approach has provided 211At isolation yields of ~ 78 % after decay and Bi attenuation corrections2. However, the use of diisopropyl ether (DIPE) in the separation process has made it difficult to reach our goal of automating the 211At isolation. Therefore, we have investigated the use of column materials to simplify the isolation of 211At and remove DIPE from the process. In this investigation we evaluated the use of a strong anion exchange resin (AG1×8), a strong cation exchange resin (AG MP-50) and a polyethylene glycol (PEG)-coated resin for separation of 211At from the bismuth target material. Anion and cation resins AG1×8 and AG MP-50 were obtained from commercial sources. A PEG-coated resin was prepared by reaction of the Merrifield resin with mPEG-OH 2000 in the pres-ence of tBuOK at 80 °C for 3 days, followed by drying under vacuum. Prior to use of the PEG resin, it was soaked in H2O. Resins (400–800 mg) were loaded into polypropylene columns (Applied Separations, Inc.). Column elution studies were conducted with and without reductants (0.75M FeSO4/1M H2SO4 or Na2S2O5) to determine their effect on capture of 211At. After target dissolution in HNO3 (and in most cases subse-quent removal of HNO3 by distillation and redis-solution of solid in 8M HCl), 211At solution was loaded onto the column, then the column was washed with 2M HCl or H2O to separate the Bi, and finally was eluted with strong base to remove the 211At. Initial studies were conducted with stable iodine to determine if reductants were effective in the presence of large amounts of bismuth ions. Studies with AG1×8 used 125I to determine if that radiohalogen could be captured and recovered from the column when eluting with boric acid buffers at pH 5.3, 8.0 or 10, or H2O at pH 7. Capture and recovery of 211At was evaluated under the same conditions. Further studies with AG1×8 involved eluting with 4M H2SO4. A limited study with AG MP-50 resin used 1M HCl as eluant. Studies with PEG-coated columns used 2M HCl, 4M HCl, 8M HCl, 16 M HNO3 and 8M HNO3 as initial (capture) eluants. Strong base (0.2, 1 or 12.5 M NaOH; 15M NH4OH) and 3 or 500 mM tetrabutylammonium bromide (TBAB) were evaluated for removal of 211At from the columns tested. The efficiency for capture of 211At on the AG1×8 column was high (99%) when loading with strong acid, but decreased when using 0.1–0.2M boric acid (69–91 %) buffer. Low 211At capture efficiencies were obtained with AG MP-50 col-umns (15–29%). High 211At capture efficiencies (96–100%) were obtained with PEG-coated resins when loading with 8M HCl or 8M HNO3, irre-spective of whether reductant was in the acid solution. Four column washings (2 mL of 2M HCl each) were required to remove all Bi prior to elution of 211At. No bismuth was detected in solution from the 4th washing in any of the elutions studied. Low (< 6%) recovery of 211At from the AG1×8 columns was obtained using the conditions studied. Good (60–79%) recovery of 211At was obtained from PEG-coated resin using 15M NH4OH. Isolation of the 211At from NH4OH solution was accomplished by distillation. In an initial study 211At distilled before obtaining a dry residue. However, later studies demonstrated that addi-tion of NaOH prior to distillation kept the 211At in the distilling flask. These studies demonstrated that PEG-coated columns could be used to isolate 211At from HNO3-dissolved bismuth targets with good non-optimized (~60%) overall recovery yields. The studies are continuing with optimization of elu-tion conditions and automation of the process

Eigenvalue comparisons for differential equations on a measure chain

The theory of $mathbf{u_0}$-positive operators with respect to a cone in a Banach space is applied to eigenvalue problems associated with the second order $Delta$-differential equation (often referred to as a differential equation on a measure chain) given by $$y^{DeltaDelta}(t)+lambda p(t)y(sigma(t))=0, qquad tin[0,1],$$ satisfying the boundary conditions $y(0)=0=y(sigma^2(1))$. The existence of a smallest positive eigenvalue is proven and then a theorem is established comparing the smallest positive eigenvalues for two problems of this type