Noise-aided gradient descent bit-flipping decoders approaching maximum likelihood decoding

International audienceIn the recent literature, the study of iterative LDPC decoders implemented on faulty-hardware has led to the counter-intuitive conclusion that noisy decoders could perform better than their noiseless version. This peculiar behavior has been observed in the finite codeword length regime, where the noise perturbating the decoder dynamics help to escape the attraction of fixed points such as trapping sets. In this paper, we will study two recently introduced LDPC decoders derived from noisy versions of the gradient descent bit-flipping decoder (GDBF). Although the GDBF is known to be a simple decoder with limited error correction capability compared to more powerful soft-decision decoders, it has been shown that the introduction of a random perturbation in the decoder could greatly improve the performance results, approaching and even surpassing belief propagation or min-sum based decoders. For both decoders, we evaluate the probability of escaping from a Trapping set, and relate this probability to the parameters of the injected noise distribution, using a Markovian model of the decoder transitions in the state space of errors localized on isolated trapping sets. In a second part of the paper, we present a modified scheduling of our algorithms for the binary symmetric channel, which allows to approach maximum likelihood decoding (MLD) at the cost of a very large number of iterations

Comparison of Three-phase Active Rectifier Solutions for Avionic Applications: Impact of the Avionic Standard DO-160 F and Failure Modes

In aircraft applications, there has been an increasing trend related with the More Electric Aircraft (MEA), which results in rapid rise in the electrical power demand on-board. One of its goals lies in minimizing weight and volume of the electrical subsystem while maintaining good power quality and efficiency. The main purpose of this paper is to present and analyze an electrical design of a three-phase Boost rectifier, a three-phase Buck rectifier and a three-phase Vienna rectifier for output power level of 10 kW and compare them in terms of weight, volume, efficiency etc. Moreover, the design is obliged to comply with specific sections of DO-160 standard for avionic equipment with 230 VAC, 360-800 Hz grid conditions. Even though all proposed solutions satisfy the standard requirements, it will be shown that the Vienna rectifier has the lowest volume and not considering failure modes, the better solution overall. However, due to increased number of semiconductors and additional circuitry required for soft start-up, the Buck rectifier would prove to be the more robust solution failure-wise

Seismic response assessment and protection of statues and busts

Recent post-earthquake surveys carried out in Europe have shown that earthquake actions pose an immense threat to museums and their contents. For example, during the earthquake on 21 July 2017 in the island of Kos (Greece), severe and widespread damage on the city’s archaeological museum was reported (Figure 1). The earthquake extensively damaged the sculpture exhibition, where many pieces were dislocated, leaned against the walls, or overturned. Fortunately, the earthquake occurred when human visitors were not in the museum, since the damage to the exhibits varied from very light (minor fracturing) to severe (complete overturning and fracture of artefacts). In the case of heavy and slender sculptures, the overturning mechanism, apart from damaging the sculptures themselves, is a serious threat to other standing exhibits in the gallery and the visitors. It is, therefore, of paramount importance to have at our disposal methods and tools for characterising the seismic risk of museum artefacts and, where necessary, proposing cost-efficient protective measures. The study of the seismic vulnerability of museum artefacts, especially of slender, human-formed statues, is related to the research on the dynamic response of rocking rigid blocks. The dynamic characteristics of the hosting structures are also important. This is evident from the fact that, on many occasions, damage to the structure was reported leaving the exhibits intact and vice-versa. Although the problem is coupled, it can be studied looking separately at the structure and its contents, provided that the contents are not attached to the building. The seismic response of building contents is a topic of growing interest, since it is directly related to seismic loss assessment and earthquake community resilience. Building contents can be either attached to the structure, or may consist of objects that are simply standing. Museum exhibits belong to the latter category, while free-standing components are often studied as rocking objects and hence their response is sensitive to acceleration and velocity-based quantities and also to their geometry. Today, there is lack of standards, while the existing approaches are general in concept and do not sufficiently address the variety of rocking objects. The problem becomes more complicated when it comes to priceless objects such as museum artefacts where more refined and targeted studies are required for understanding their seismic response and also for proposing rapid tools for assessing their seismic risk. The paper presents an extensive experimental campaign on the seismic response of artefacts, with emphasis on statues and busts. The tests took place in the framework of SEREME project (Seismic Resilience of Museum Contents) at the AZALEE seismic simulator of CEA in Saclay, Paris under the auspices of the SERA project. The aim is to understand the seismic response of statues and busts and then develop novel and cost-effective risk mitigation schemes for improving the seismic resilience of museum valuable contents. The study is focused on the investigation of the seismic response of two real-scale marble roman statues and three busts of three roman emperors standing on pedestals of different types and size. Both isolated and non-isolated artefacts are considered, while two new and highly efficient base isolation systems, tailored to art objects, will be tested. The first isolator is a pendulum-based system, while the second utilizes Shape Memory Alloy wires. Furthermore, the paper examines the importance of the hosting building, i.e. building type and story. Specifically tailored, numerical models of varying complexity, for single and two-block rocking systems, were developed for the needs of this study and are also assessed against the experimental results

Urgent need to clarify the definition of chronic critical limb ischemia - a position paper from the European Society for Vascular Medicine

Chronic critical lower limb ischemia (CLI) has been defined as ischemia that endangers the leg. An attempt was made to give a precise definition of CLI, based on clinical and hemodynamic data (Second European Consensus). CLI may be easily defined from a clinical point of view as rest pain of the distal foot or gangrene or ulceration. It is probably useful to add leg ulcers of other origin which do not heal because of severe ischemia, and to consider the impact of frailty on adverse outcome. From a hemodynamic viewpoint there is no consensus and most of the existing classifications are not based upon evidence. We should thus propose a definition and then validate it in a prospective cohort in order to define the patients at major risk of amputation, and also to define the categories of patients whose prognosis is improved by revascularisation. From today\u27s available data, it seems clear that the patients with a systolic toe pressure (STP) below 30 mmHg must be revascularised whenever possible. However other patients with clinically suspected CLI and STP above 30 mmHg must be evaluated and treated in specialised vascular units and revascularisation has to be discussed on a case by case basis, taking into account other data such as the WiFi classification for ulcers.In conclusion, many useful but at times contradictory definitions of CLI have been suggested. Only a few have taken into account evidence, and none have been validated prospectively. This paper aims to address this and to give notice that a CLI registry within Europe will be set up to prospectively validate, or not, the previous and suggested definitions of CLI

Impact of land use on urban mobility patterns, emissions and air quality in a Portuguese medium-sized city

The main objective of this work was to evaluate the impact of urban development trends in mobility patterns of a medium sized Portuguese city and air quality consequences, using a sequential modeling process, comprising i) land use and transportation, TRANUS model; ii) road traffic air pollutants emissions, TREM model and; iii) air quality, TAPM model. This integrated methodology was applied to a medium sized Portuguese city. In order to evaluate the implementation of the methodology, a preliminary study was performed, which consisted on the comparison of modeled mobility patterns and CO and PM(10) concentrations with measured data used in the definition of the current scenario. The comparison between modeled and monitored mobility patterns at the morning peak hour for a weekday showed an RMSE of 31%. Regarding CO concentrations, an underestimation of the modeled results was observed. Nevertheless, the modeled PM(10) concentrations were consistent with the monitored data. Overall, the results showed a reasonable consistency of the modeled data, which allowed the use of the integrated modeling system for the study scenarios. The future scenarios consisted on the definition of different mobility patterns and vehicle technology characteristics, according to two main developing trends: (1) "car pooling" scenario, which imposes a mean occupancy rate of 3 passengers by vehicle and (2) the "Euro 6" scenario, which establishes that all vehicles accomplish at least the Euro 6 standard technology. Reductions of 54% and 83% for CO, 44% and 95% for PM(10), 44% and 87% for VOC and 44% and 79% for NO(x) emissions were observed in scenarios 1 and 2, respectively. Concerning air quality, a reduction of about 100 mug m(-3) of CO annual average concentration was observed in both scenarios. The results of PM(10) annual concentrations showed a reduction of 1.35 mug m(-3) and 2.7 mug m(-3) for scenarios 1 and 2 respectively

GLACE: the global land–atmosphere coupling experiment. Part I: overview

Permission to place copies of these works on this server has been provided by the American Meteorological Society (AMS). The AMS does not guarantee that the copies provided here are accurate copies of the published work. © Copyright 2006 American Meteorological Society (AMS). Permission to use figures, tables, and brief excerpts from this work in scientific and educational works is hereby granted provided that the source is acknowledged. Any use of material in this work that is determined to be “fair use” under Section 107 of the U.S. Copyright Act or that satisfies the conditions specified in Section 108 of the U.S. Copyright Act (17 USC §108, as revised by P.L. 94-553) does not require the AMS’s permission. Republication, systematic reproduction, posting in electronic form on servers, or other uses of this material, except as exempted by the above statement, requires written permission or a license from the AMS. Additional details are provided in the AMS Copyright Policy, available on the AMS Web site located at (http://www.ametsoc.org/AMS) or from the AMS at 617-227-2425 or [email protected] Global Land–Atmosphere Coupling Experiment (GLACE) is a model intercomparison study focusing on a typically neglected yet critical element of numerical weather and climate modeling: land–atmosphere coupling strength, or the degree to which anomalies in land surface state (e.g., soil moisture) can affect rainfall generation and other atmospheric processes. The 12 AGCM groups participating in GLACE performed a series of simple numerical experiments that allow the objective quantification of this element for boreal summer. The derived coupling strengths vary widely. Some similarity, however, is found in the spatial patterns generated by the models, with enough similarity to pinpoint multimodel “hot spots” of land–atmosphere coupling. For boreal summer, such hot spots for precipitation and temperature are found over large regions of Africa, central North America, and India; a hot spot for temperature is also found over eastern China. The design of the GLACE simulations are described in full detail so that any interested modeling group can repeat them easily and thereby place their model’s coupling strength within the broad range of those documented here

Exciting surface plasmons with transformation media

The final publication is available at Springer via http://dx.doi.org/10.1007/s11468-012-9361-5We present a way of exciting surface plasmon polaritons along non-patterned metallic surfaces by means of a flat squeezing slab designed with transformation optics. The slab changes the dispersion relation of incident light, enabling evanescent coupling to propagating surface plasmons. Unlike prism couplers, the proposed device does not introduce reflections at its input interface. Moreover, its compact geometry is suitable for integration. A feasible dielectric implementation of the coupler is suggested. Finally, we show that the angular response of the device can be engineered by using a non-uniform compression factor. As an example, we design a coupler with a half-power angular bandwidth 2. 5 times higher than that of a conventional dielectric coupler. © 2012 Springer Science+Business Media, LLC.Financial support by Spanish Ministerio de Ciencia e Innovacion (contracts CSD2008-00066 and TEC2008-06871-C02, and FPU grant) is gratefully acknowledged.García Meca, C.; Ortuño Molinero, R.; Martí Sendra, J.; Martínez Abietar, AJ. (2012). Exciting surface plasmons with transformation media. Plasmonics. 7(4):701-707. https://doi.org/10.1007/s11468-012-9361-5S70170774Raether H (1988) Surface plasmons on smooth and rough surfaces and on gratings. Springer-Verlag, BerlinBarnes WL, Dereux A, Ebbesen TW (2003) Surface plasmon subwavelength optics. Nature 424:824–830Maier SA (2007) Plasmonics: fundamentals and applications. Springer, New YorkSchuller JA, Barnard ES, Cai W, Jun YC, White JS, Brongersma ML (2010) Plasmonics for extreme light concentration and manipulation. Nat Mater 9:193–204Brongersma ML, Shalaev VM (2010) The case for plasmonics. Science 328:440–441Liu Y, Zentgraf T, Bartal G, Zhang X (2010) Transformational plasmon optics. Nano Lett 10:1991–1997Huidobro PA, Nesterov ML, Martín-Moreno L, García-Vidal FJ (2010) Transformation optics for plasmonics. Nano Lett 10:1985–1990Kadic M, Guenneau S, Enoch S (2010) Transformational plasmonics: cloak, concentrator and rotator for SPPs. Opt Express 18:12027–12032Zhang J, Xiao S, Wubs M, Mortensen NA (2011) Surface plasmon wave adapter designed with transformation optics. ACS Nano 5:4359–4364Pendry JB, Schurig D, Smith DR (2006) Controlling electromagnetic fields. Science 312:1780–1782Leonhardt U (2006) Optical conformal mapping. Science 312:1777–1780Leonhardt U, Philbin TG (2006) General relativity in electrical engineering. New J Phys 8:247Sambles JR, Bradbery GW, Yang F (1991) Optical excitation of surface plasmons: an introduction. Contemp Phys 32:173–183Rahm M, Roberts DA, Pendry JB, Smith DR (2008) Transformation-optical design of adaptive beam bends and beam expanders. Opt Express 16:11555–11567Vasic B, Isic G, Gajic R, Hingerl K (2009) Coordinate transformation based design of confined metamaterial structures. Phys Rev B 79:85103Tichit P, Burokur SN, Lustrac A (2009) Waveguide taper engineering using coordinate transformation technology. Opt Express 18:767–772Zang X, Jiang C (2010) Manipulating the field distribution via optical transformation. Opt Express 18:10168–10176García-Meca C, Tung MM, Galán JV, Ortuño R, Rodríguez-Fortuño FJ, Martí J, Martínez A (2011) Squeezing and expanding light without reflections via transformation optics. Opt Express 19:3562–3575Li J, Han S, Zhang S, Bartal G, Zhang X (2009) Designing the Fourier space with transformation optics. Opt Lett 34:3128–3130Li J, Pendry JB (2008) Hiding under the carpet: a new strategy for cloaking. Phys Rev Lett 101:20390

Stabilization of mid-sized silicon nanoparticles by functionalization with acrylic acid

We present an enhanced method to form stable dispersions of medium-sized silicon nanoparticles for solar cell applications by thermally induced grafting of acrylic acid to the nanoparticle surface. In order to confirm their covalent attachment on the silicon nanoparticles and to assess the quality of the functionalization, X-ray photoelectron spectroscopy and diffuse reflectance infrared Fourier spectroscopy measurements were carried out. The stability of the dispersion was elucidated by dynamic light scattering and Zeta-potential measurements, showing no sign of degradation for months

Evaluation of the MYCOPLASMA IST3 urogenital mycoplasma assay in an international multicentre trial

Objectives To evaluate the accuracy, susceptibility and specificity of MYCOPLASMA IST3, the next generation of the most popular culture-based in vitro diagnostic device designed to detect, identify and test the susceptibility of urogenital mycoplasma infections. Methods MYCOPLASMA IST3 was evaluated against culture- and molecular-based gold standard methodologies to detect, identify, enumerate and determine antimicrobial resistance for Mycoplasma hominis and Ureaplasma species in 516 clinical samples collected across France, Serbia and the UK. Sample types included vulvovaginal/endocervical or urethral swabs (dry swab or eSwab®), semen and urine samples, which included blinded analysis following addition of a panel of 80 characterized control strains. Results Overall species identification was excellent for both Ureaplasma spp. (98.4% sensitivity, 99.7% specificity) and M. hominis (95.7% sensitivity, 100% specificity) relative to combined colony morphology on agar and quantitative PCR standards. Non-dilution-based bacterial load estimation by the assay was accurate between 83.7% (M. hominis) and 86.3% (Ureaplasma spp.) of the time (increased to 94.2% and 100%, respectively, if ±10-fold variance was allowed) relative to colonies counted on agar. Resistance accuracy for Ureaplasma spp. varied from gold standards for only 11/605 of individual tests (major error rate = 1.8%) and for 14/917 individual tests for M. hominis (major error rate = 1.5%). Conclusions The redesigned MYCOPLASMA IST3 assay eliminated previous shortcomings by providing independent accurate resistance screening of M. hominis and Ureaplasma species, even in mixed infections, with CLSI-compliant thresholds. Specificity, sensitivity and enumeration estimates correlated closely with the confirmatory methods