Synthesis and Study of Fully Biodegradable Composites Based on Poly(butylene succinate) and Biochar

Biodegradable polymers offer a promising alternative to the global plastic problems and especially in the last decade, to the microplastics problems. For the first time, samples of poly(butylene succinate) (PBSu) biocomposites containing 1, 2.5, and 5 wt% biochar (BC) were prepared by in situ polymerization via the two-stage melt polycondensation procedure. BC was used as a filler for the PBSu to improve its mechanical properties, thermal transitions, and biodegradability. The structure of the synthesized polymers was examined by 1H and 13C nuclear magnetic resonance (NMR) and X-Ray diffraction (XRD) along with an estimation of the molecular weights, while differential scanning calorimetry (DSC) and light flash analysis (LFA) were also employed to record the thermal transitions and evaluate the thermal conductivity, respectively. It was found that the amount of BC does not affect the molecular weight of PBSu biocomposites. The fine dispersion of BC, as well as the increase in BC content in the polymeric matrix, significantly improves the tensile and impact strengths. The DSC analysis results showed that BC facilitates the crystallization of PBSu biocomposites. Due to the latter, a mild and systematic increase in thermal diffusivity and conductivity was recorded indicating that BC is a conductive material. The molecular mobility of PBSu, local and segmental, does not change significantly in the biocomposites, whereas the BC seems to cause an increase in the overall dielectric permittivity. Finally, it was found that the enzymatic hydrolysis degradation rate of biocomposites increased with the increasing BC content

Thermal degradation kinetics and decomposition mechanism of PBSu nanocomposites with silica-nanotubes and strontium hydroxyapatite nanorods

Novel poly(butylene succinate) (PBSu) nanocomposites containing 5 and 20 wt% mesoporous strontium hydroxyapatite nanorods (SrHNRs) and silica nanotubes (SiNTs) were prepared by melt-mixing. A systematic investigation of the thermal stability and decomposition kinetics of PBSu was performed using pyrolysis-gas chromatography–mass spectroscopy (Py-GC–MS) and thermogravimetry (TG). Thorough studies of evolving decomposition compounds along with the isoconversional and model-fitting analysis of mass loss data led to the proposal of a decomposition mechanism for PBSu. Moreover, the effects of SrHNRs and SiNTs on the thermal stability and decomposition kinetics of PBSu were also examined in detail. The complementary use of these techniques revealed that the incorporation of SiNTs in PBSu does not induce significant effects neither on its thermal stability nor on its decomposition mechanism. In contrast, the addition of SrHNRs resulted in the catalysis of the initial decomposition steps of PBSu and also in modified decomposition mechanisms and activation energies. The evolving gaseous products of PBSu and their evolution pattern in the SiNT nanocomposites were the same as in neat PBSu, while they were slightly modified for the SrHNR nanocomposites, confirming the findings from thermogravimetric analysis

Synthesis and Characterization of In-Situ-Prepared Nanocomposites Based on Poly(Propylene 2,5-Furan Dicarboxylate) and Aluminosilicate Clays

Poly(propylene 2,5-furan dicarboxylate) (PPF), or poly(trimethylene 2,5-furan dicarboxylate) (PTF), is a biobased alipharomatic polyester that is expected to replace its fossil-based terephthalate (PPT) and naphthate (PPN) homologues. PPF possesses exceptional gas barrier properties, but its slow crystallization rate might affect its success in specific applications in the future. Therefore, a series of PPF based nanocomposites with the nanoclays Cloisite®-Na (MMT), Cloisite®-20A (MMT 20A), and halloysite nanotubes (HNT) were synthesized via the in situ transterification and polycondensation method. The effect of the nanoclays on the structure, thermal, and crystallization properties of PPF was studied with several methods including infrared spectroscopy (IR), Nuclear Resonance Spectroscopy (1H-NMR), Wide Angle X-ray Diffraction (WAXD), Thermogravimetric Analysis (TGA), and Differential Scanning Calorimetry (DSC). The insertion of the nanofillers in the polymer matrix altered the crystallization rates, and TGA results showed good thermal stability, since no significant mass loss occurred up to 300 °C. Finally, the degradation mechanism was studied in depth with Pyrolysis-Gas Chromatography/Mass Spectroscopy, and it was found that β-scission is the dominant degradation mechanism

Antibacterial properties and regenerative potential of Sr²+ and Ce³+ doped fluorapatites; a potential solution for peri-implantitis

Scaffolds and implants in orthopaedics and regenerative dentistry usually fail because of bacterial infections. A promising solution would be the development of biomaterials with both significant regenerative potential and enhanced antibacterial activity. Working towards this direction, fluorapatite was synthesised and doped with Sr²+ and Ce³+ ions in order to tailor its properties. After experiments with four common bacteria (i.e. E. Coli, S. Aureus, B. Subtilis, B. Cereus), it was found that the undoped and the Ce³+ doped fluorapatites present better antibacterial response than the Sr²+ doped material. The synthesised minerals were incorporated into chitosan scaffolds and tested with Dental Pulp Stem Cells (DPSCs) to check their regenerative potential. As was expected, the scaffolds containing Sr²+-doped fluorapatite, presented high osteoconductivity leading to the differentiation of the DPSCs into osteoblasts. Similar results were obtained for the Ce³+-doped material, since both the concentration of osteocalcin and the RUNX2 gene expression were considerably higher than that for the un-doped mineral. Overall, it was shown that doping with Ce³+ retains the good antibacterial profile of fluorapatite and enhances its regenerative potential, which makes it a promising option for dealing with conditions where healing of hard tissues is compromised by bacterial contamination

Development of slate fiber reinforced high density polyethylene composites for injection molding

During the last decade the use of fiber reinforced composite materials has consolidated as an attracting alternative to traditional materials due to an excellent balance between mechanical properties and lightweight. One drawback related to the use of inorganic fibers such as those derived from siliceous materials is the relative low compatibility with conventional organic polymer matrices. Surface treatments with coupling agents and the use of copolymers allow increasing fiber-matrix interactions which has a positive effect on overall properties of composites. In this research work we report the use of slate fiber treated with different coupling agents as reinforcement for high density polyethylene from sugarcane. A silane (propyltrimethoxy silane; PTMS) and a graft copolymer (polyethylene-graft-maleic anhydride; PE-g-MA) were used to improve fiber-matrix interactions on HOPE-slate fiber. The effect of the different compatibilizing systems and slate fiber content were evaluated by scanning electron microscopy (SEM), dynamic thermomechanical analysis (DTMA) as well as mechanical properties (tensile, flexural and impact). The results show that the use of silane coupling agents leads to higher fiber-matrix interactions which has a positive effect on overall mechanical properties. Interesting results are obtained for composites containing 30 wt.% slate fiber previously treated with propyltrimethoxy silane (PTMS) with an increase in tensile and flexural strength of about 16% and 18% respectively. (C) 2014 Elsevier Ltd. All rights reserved.Authors thank "Ministerio de Economia y Competitividad" ref: MAT2011-28468-C02-02 and "Conselleria d'Educacio, Cultura i Esport" - Generalitat Valenciana ref: GV/2014/008 for financial support.Carbonell Verdú, A.; García García, D.; Jordá Vilaplana, A.; Samper Madrigal, MD.; Balart Gimeno, RA. (2015). Development of slate fiber reinforced high density polyethylene composites for injection molding. Composites Part B: Engineering. 69:460-466. https://doi.org/10.1016/j.compositesb.2014.10.026S4604666