Recovering industrial heritage: restoration of the wine cellar cooperative in Falset (Catalonia, Spain)

Awareness regarding conservation of industrial heritage is recent. Several policies have been adopted to start protecting these buildings because of their historic, artistic and scientific values. Wine cellars are an important example of industrial heritage in Catalonia due to the tradition of this product in the territory and the influence of Art Nouveau and Catalan ‘Noucentisme’ in their construction and style. The wine cellar in Falset, built by Cèsar Martinell in 1919, has recently been restored and still maintains its original function. This article analyses its history, its architectonic and construction characteristics, as well as the restoration process carried out in 2009, which consisted of recovering its original appearance and allowed to emphasize the architectural value of the building. This restoration is a prototypical example whose experience can be applied in other cases of restoration of wine cellars both for the characteristics of the building and for its good restoration practices. This restoration enabled the wine cellar to continue carrying out its original industrial function, providing suitable conditions to add a new cultural use as wellPeer ReviewedPostprint (author's final draft

A Review of Recycling Methods for Fibre Reinforced Polymer Composites

This paper presents a review of waste disposal methods for fibre reinforced polymer (FRP) ma-terials. The methods range from waste minimisation, repurposing, reusing, recycling, incinera-tion, and co-processing in a cement plant to dumping in a landfill. Their strength, limitations, and key points of attention are discussed. Both glass and carbon fibre reinforced polymer (GFRP and CFRP) waste management strategies are critically reviewed. The energy demand and cost of FRP waste disposal routes are also discussed. Landfill and co-incineration are the most common and cheapest techniques to discard FRP scrap. Three main recycling pathways, including mechanical, thermal, and chemical recycling, are reviewed. Chemical recycling is the most energy-intensive and costly route. Mechanical recycling is only suitable for GFRP waste, and it has actually been used at an industrial scale by GFRP manufacturers. Chemical and thermal recycling routes are more appropriate for reclaiming carbon fibres from CFRP, where the value of reclaimed fibres is more than the cost of the recycling process. Discarding FRP waste in a sustainable manner pre-sents a major challenge in a circular economy. With strict legislation on landfill and other envi-ronmental limits, recycling, reusing, and repurposing FRP composites will be at the forefront of sustainable waste-management strategies in the future

Furniture design and product development principles considering end-of-life options and design for environment strategies

During last decades, environmental issues come into prominence and some governmental or organizational regulations are legislated to reduce environmental impacts of products within their life cycle. At the same time, costumers consider not only price, quality, branding, uniqueness, availability but also environmental impact, safety, and overall sustainability of products they select. Therefore, producers are addressing environmental impact of products they are producing and also making changes to their production process. This project is addressing End-of-Life (EoL) Options of wooden furniture. ^ Although wood is eco-friendly and natural material, its technological process, use and disposal might have ecological problem and challenge. Therefore, it should be considered individually from conception to end of its life to increase ecological quality. The main environmental problem for wooden furniture industry comes up during manufacturing process and disposal of furniture. Applying Design for Environment (DfE) strategies and End of Life (EoL) options can reduce product environmental impact. ^ This study will focus on implementation of DfE and EoL Options in the final stage of the selected product life cycle. Wooden stools constructed by different joinery methods were studies to demonstrate this case. A few solutions are presented: substitution of materials, joinery (such as replacement of metal fasteners with fully wooden joinery), and structure reinforcement techniques. These and other techniques will be investigated for production of reusable and recyclable furniture. The overall goal is to increase the awareness of furniture designers, producers and suppliers of new environmental regulations and to offer some product improvement solutions

Circular Composites

Composites are increasingly used to optimize the performance of applications as their properties can be tuned to achieve the desired functionality. The sustainability advantages during the use phase are not yet matched by lower impacts in the lifecycle of composite materials and products. In a circular economy this is problematic. This book will serve as a guide to designers who want to contribute with innovative and effective solutions. Circular recovery strategies, ranging from reuse to restructuring and recycling, are connected to the design process and concrete design approaches. By providing clear design guidelines and illustrative examples in a structured way the information is readily accessible and applicable to designers

Analysis of material efficiency aspects of personal computers product group

This report has been developed within the project ‘Technical support for environmental footprinting, material efficiency in product policy and the European Platform on Life Cycle Assessment’ (LCA) (2013-2017) funded by the Directorate-General for Environment. The report summarises the findings of the analysis of material-efficiency aspects of the personal-computer (PC) product group, namely durability, reusability, reparability and recyclability. It also aims to identify material-efficiency aspects which can be relevant for the current revision of the Ecodesign Regulation (EU) No 617/2013. Special focus was given to the content of EU critical raw materials (CRMs) ( ) in computers and computer components, and how to increase the efficient use of these materials, including material savings thanks to reuse and repair and recovery of the products at end of life. The analysis has been based mainly on the REAPro method ( ) developed by the Joint Research Centre for the material-efficiency assessment of products. This work has been carried out in the period June 2016-September 2017, in parallel with the development of The preparatory study on the review of Regulation 617/2013 (Lot 3) — computers and computer servers led by Viegand Maagøe and Vlaamse Instelling voor Technologisch Onderzoek NV (VITO) (2017) ( ). During this period, close communication was maintained with the authors of the preparatory study. This allowed ensuring consistency between input data and assumptions of the two studies. Moreover, outcomes of the present research were used as scientific basis for the preparatory study for the analysis of material-efficiency aspects for computers. The research has been differentiated as far as possible for different types of computers (i.e. tablet, notebooks and desktop computers). The report starts with the analysis of the technical and scientific background relevant for material-efficiency aspects of computers, such as market sales, expected lifetime, bill of materials, and a focus on the content of CRMs (especially cobalt in batteries, rare earths including neodymium in hard disk drives and palladium in printed circuit boards). Successively the report analyses the current practices for repair, reuse and recycling of computers. Based on results available from the literature, material efficiency of the product group has the potential to be improved, in particular the lifetime extension. The residence time ( ) of IT equipment put on the market in 2000 versus 2010 generally declined by approximately 10 % (Huisman et al., 2012), while consumers expressed their preference for durable goods, lasting considerably longer than they are typically used (Wieser and Tröger, 2016). Design barriers (such as difficulties for the disassembly of certain components or for their processing for data sanitisation) can hinder the repair and the reuse of products. Malfunction and accident rates are not negligible (IDC, 2016, 2010; SquareTrade, 2009) and difficulties in repair may bring damaged products to be discarded even if still functioning. Once a computer reaches the end of its useful life, it is addressed to ‘waste of electrical and electronic equipment’ (WEEE) recycling plants. Recycling of computers is usually based on a combination of manual dismantling of certain components (mainly components containing hazardous substances or valuable materials, e.g. batteries, printed circuit boards, display panels, data-storage components), followed by mechanical processing including shredding. The recycling of traditional desktop computers is perceived as non-problematic by recyclers, with the exception of some miniaturised new models (i.e. mini desktop computers), which still are not found in recycling plants and which could present some difficulties for the extraction of printed circuit boards and batteries (if present). The design of notebooks and tablets can originate some difficulties for the dismantling of batteries, especially for computers with compact design. Recycling of plastics from computers of all types is generally challenging due to the large use of different plastics with additives, such as flame retardants. According to all the interviewed recyclers, recycling of WEEE plastics with flame retardant is very poor or null with current technologies. Building on this analysis, the report then focuses on possible actions to improve material efficiency in computers, namely measures to improve (a) waste prevention, (b) repair and reuse and (c) design for recycling. The possible actions identified are listed hereinafter. (a) Waste prevention a.1 Implementation of dedicated functionality ( ) for the optimisation of the lifetime of batteries in notebooks: the lifetime of batteries could be extended by systematically implementing a preinstalled functionality on notebooks, which makes it possible to optimise the state of charge (SoC) of the battery when the device is used in grid operation (stationary). By preventing the battery remaining at full load when the notebook is in grid operation, the lifetime of batteries can be potentially extended by up to 50 %. Users could be informed about the existence and characteristics of such a functionality and the potential benefits related to its use. a.2 Decoupling external power supplies (EPS) from personal computers: the provision of information on the EPS specifications and the presence/absence of the EPS in the packaging of notebooks and tablets could facilitate the reuse by the consumer of already-available EPS with suitable characteristics. Such a measure could promote the use of common EPS across different devices, as well as the reuse of already-owned EPS. This would result in a reduction in material consumption for the production of unnecessary power supplies (and related packaging and transport) and overall a reduction of treatment of electronic waste. The International Electrotechnical Commission (IEC) technical specification (TS) 62700, the Standard Institute of Electrical and Electronics Engineers (IEEE) 1823 and Recommendation ITU-T L.1002 can be used to develop standards for the correct definition of connectors and power specifications. a.3 Provision of information about the durability of batteries: the analysis identified the existence of endurance tests suitable for the assessment of the durability of batteries in computers according to existing standards (e.g. EN 61960). The availability of information about these endurance tests could help users to get an indication on the residual capacity of the battery after a predefined number of charge/discharge cycles. Moreover, such information would allow for comparison between different products and potentially push the market towards longer-lasting batteries. a.4 Provision of information about the ‘liquid ingress protection (IP) class’ for personal computers: this can be assessed for a notebook or tablet by performing specific tests, developed according to existing standards (e.g. IEC 60529). Users can be informed about the level of protection of the computer against the ingress of liquids (e.g. dripping water or spraying water or water jets) and in this way prevent one of the most common causes of computer failure. The yearly rate of estimated material saving if dedicated functionality for the optimisation of the lifetime of batteries (a.1) were used ranges from around 2 360 to 5 400 tonnes (t) of different materials per year. About 450 t of cobalt, 100 t of lithium, 210 t of nickel and 730 t of copper could be saved every year. The estimated potential savings of materials when EPS are decoupled from notebooks and tablets (a.2) are in the range 2 300-4 600 t/year (80 % related to the notebook category, and 20 % to tablets). These values can be obtained when 10-20 % of notebooks and tablets are sold without an EPS, as users can reuse already-owned and compatible EPS. Under these conditions, for example, about 190-370 t of copper can be saved every year. This estimate may increase when the same EPS can be used for both notebooks and tablets (at the moment the assessment is based on the assumption that the two product types were kept separated). Further work is needed to assess the potential improvements thanks to the provision of information about the durability of batteries (a.3), and about the ‘liquid-IP class’ (a.4). The former option (a.3) has the potential to boost competition among battery manufacturers, resulting in more durable products. The latter option (a.4) has the potential to reduce computer damage due to liquid spillage, ranked among the most recurrent failure modes. (b) Repair/reuse b.1 and b.2 Provision of information to facilitate computer disassembly: the disassembly of relevant components (such as the display panel, keyboard, data storage, batteries, memory and internal power-supply units) plays a key role to enhance repair and reuse of personal computers. Some actions have therefore been discussed (b.1) to provide professional repair operators with documentation about the sequence of disassembly, extraction, replacement and reassembly operations needed for each relevant component of personal computers, and (b.2) to provide end-users with specific information about the disassembly and replacement of batteries in notebooks and tablets. b.3 Secure data deletion for personal computers: this is the process of deliberately, permanently and irreversibly erasing all traces of existing data from storage media, overwriting the data completely in such a way that access to the original data, or parts of them, becomes infeasible for a given level of effort. Secure data deletion is essential for the security of personal data and to allow the reuse of computers by a different user. Secure data deletion for personal computers can be ensured by means of built-in functionality. A number of existing national standards (HMG IS Standard No 5 (the United Kingdom), DIN 66399 (Germany), NIST 800-88r1 (the United States (US)) can be used as a basis to start standardisation activities on secure data deletion. The estimated potential savings of materials due to the provision of information and tools to facilitate computer disassembly were quantified in the range of 150-620 t/year for mobile computers (notebooks and tablets) within the first 2 years of use, and in the range of 610 2 460 t/year for mobile computers older than 2 years. Secure data deletion of personal computers, instead, is considered a necessary prerequisite to enhance reuse. The need to take action on this is related to policies on privacy and protection of personal data, as the General Data Protection Regulation (EU) 2016/679 and in particular its Article 25 on ‘data protection by design and by default’. Future work is needed to strengthen the analysis, however it was estimated that secure data deletion has the potential to double volume of desktop, notebook and tablet computers reused after the first useful lifetime. (c) Recyclability c.1 Provision of information to facilitate computer dismantling: computers could be designed so that crucial components for material aspects (e.g. content of hazardous substances and/or valuable materials) can be easily identified and extracted in order to be processed by means of specific recycling treatments. Design for dismantling can focus on components listed in Annex VII of the WEEE directive ( ). The ‘ease of dismantling’ can be supported by the provision of relevant information (such as a diagram of the product showing the location of the components, the content of hazardous substances, instructions on the sequence of operations needed to remove these components, including type and number of fastening techniques to be unlocked, and tool(s) required). c.2 Marking of plastic components: although all plastics are theoretically recyclable, in practice the recyclability of plastics in computers is generally low, mainly due to the large amount of different plastic components with flame retardants (FRs) and other additives. Marking of plastic components according to existing standards (e.g. ISO 11469 and ISO 1043 series) can facilitate identification and sorting of plastic components during the manual dismantling steps of the recycling. c.3 FR content: according to all the recyclers interviewed, FRs are a major barrier to plastics recycling. Current mechanical-sorting processes of shredded plastics are characterised by low efficiency, while innovative sorting systems are still at the pilot stage and have been shown to be effective only in certain cases. Therefore, the provision of information on the content of FRs in plastic components is a first step to contribute to the improvement of plastics recycling. Plastics marking (as discussed above) can contribute to the separation of plastics with FRs during the manual dismantling, allowing for their recycling at higher rates (in line with the prescription of IEC/TR 62635, 2015). However, detailed information about FRs content could be given in a more systematised way, for example through the development of specific indexes. These indexes could support recyclers in checking the use of FRs in computers and in developing future processes and technologies suitable for plastics recycling. Moreover, these indexes could support policymakers in monitoring the use of FRs in the products and, in the medium-long term, to promote products that use smaller quantities of FRs. An example of a FR content index is provided in this report. c.4 Battery marks: the identification of the chemistry type of batteries in computers is necessary in order to have efficient identification and sorting, and thus to improve the material efficiency during the recycling. It is proposed to start standardisation activities to establish standard marking symbols for batteries. The examples of the ‘battery-recycle mark’, developed by the Battery Association of Japan (BAJ), and the current standardisation activities for the IEC 62902 (standard marking symbols for batteries with a volume higher than 900 cm3) may be used as references to develop ad hoc standards. The benefits of actions for the design for recycling can be relevant. In particular, the proposed actions should contribute to increase the amounts of materials that will be recycled (6 350-8 900 t/year), in particular plastics (5 950-7 960 t/year of additional plastics), but also metals such as cobalt (55-110 t), copper (240-610 t), rare earths as neodymium and dysprosium (2 7 t) and various precious metals (gold (0.1-0.4 t), palladium (0.1-0.4 t) and silver (2 7 t)). Compared to the amount of materials recycled in the EU (2012 data), these values would represent a recycling increase of 1-2 % for cobalt, 2-5 % for palladium, and 13-50 % for rare earths.JRC.D.3-Land Resource

Current status of recycling of fibre reinforced polymers: Review of technologies, reuse and resulting properties

AbstractA complete review of the different techniques that have been developed to recycle fibre reinforced polymers is presented. The review also focuses on the reuse of valuable products recovered by different techniques, in particular the way that fibres have been reincorporated into new materials or applications and the main technological issues encountered. Recycled glass fibres can replace small amounts of virgin fibres in products but not at high enough concentrations to make their recycling economically and environmentally viable, if for example, thermolysis or solvolysis is used. Reclaimed carbon fibres from high-technology applications cannot be reincorporated in the same applications from which they were recovered, so new appropriate applications have to be developed in order to reuse the fibres. Materials incorporating recycled fibres exhibit specific mechanical properties because of the particular characteristics imparted by the fibres. The development of specific standards is therefore necessary, as well as efforts in the development of solutions that enable reusers to benefit from their reinforcement potential. The recovery and reuse of valuable products from resins are also considered, but also the development of recyclable thermoset resins. Finally, the economic and environmental aspects of recycling composite materials, based on Life Cycle Assessment, are discussed

Alternative water sources for urban consumers – A novel technology for the City of Cape Town urban resident

South Africa is classified as being the 30th driest country in the world and is regarded as a water scarce country. However, for the urban residents of the City of Cape Town, the ability to reduce their municipal water consumption through initiatives, other than simply using less water, is limited. Hence, there is a need for affordable, simple and compact technical solutions which allow urban populations residing in high density developments to make use of alternative sources of water, specifically greywater, to reduce their municipal water demand. Existing commercial technologies were considered, together with the socio-economic and technical constraints of an illustrative middle-income urban household in the City of Cape Town (CoCT). It was found that each commercial technology considered satisfied some, but not all, constraints characteristic of the household. For instance, the treatment device may produce treated water of a high quality. However, it may not be financially feasible for the consumer. Of the commercial technologies considered, there is no single commercial technology which can offer a complete solution within the socio-economic and technical constraints of the household. For this reason, the opportunity exists to produce an innovative technical solution. The proposed greywater treatment device consists of four cylindrical chambers in a vertical arrangement. Raw greywater enters the top chamber and treated greywater is extracted from the bottom chamber forming the base. The treatment processes undergone as the greywater flows through the treatment device include, in the following order, pre-filtration, biological treatment (Activated Sludge), clarification, filtration and disinfection. The process is driven by a combination of gravity and electrical energy. The proposed design is constructed using readily available materials and components. It is modular in its construction, allowing for easy maintenance, assembly and an increase in design flexibility. Evaluating the design against the same evaluation criteria stipulated for the existing commercial technologies showed that the proposed design may be an appropriate solution for the illustrative middle-income household within the City of Cape Town and is a novel technical solution

Review : Best Practices In Educating Sustainability and Heritage

This result has been produced as a part of O1 INTELECTUAL OUTPUT "01: Review of the Best Practices on Educating Sustainability and Heritage" within HERSUS project, Erasmus + Strategic Partnerships for higher education