Baseband analog front-end and digital back-end for reconfigurable multi-standard terminals

Multimedia applications are driving wireless network operators to add high-speed data services such as Edge (E-GPRS), WCDMA (UMTS) and WLAN (IEEE 802.11a,b,g) to the existing GSM network. This creates the need for multi-mode cellular handsets that support a wide range of communication standards, each with a different RF frequency, signal bandwidth, modulation scheme etc. This in turn generates several design challenges for the analog and digital building blocks of the physical layer. In addition to the above-mentioned protocols, mobile devices often include Bluetooth, GPS, FM-radio and TV services that can work concurrently with data and voice communication. Multi-mode, multi-band, and multi-standard mobile terminals must satisfy all these different requirements. Sharing and/or switching transceiver building blocks in these handsets is mandatory in order to extend battery life and/or reduce cost. Only adaptive circuits that are able to reconfigure themselves within the handover time can meet the design requirements of a single receiver or transmitter covering all the different standards while ensuring seamless inter-interoperability. This paper presents analog and digital base-band circuits that are able to support GSM (with Edge), WCDMA (UMTS), WLAN and Bluetooth using reconfigurable building blocks. The blocks can trade off power consumption for performance on the fly, depending on the standard to be supported and the required QoS (Quality of Service) leve

Algorithm-Architecture Co-Design for Digital Front-Ends in Mobile Receivers

The methodology behind this work has been to use the concept of algorithm-hardware co-design to achieve efficient solutions related to the digital front-end in mobile receivers. It has been shown that, by looking at algorithms and hardware architectures together, more efficient solutions can be found; i.e., efficient with respect to some design measure. In this thesis the main focus have been placed on two such parameters; first reduced complexity algorithms to lower energy consumptions at limited performance degradation, secondly to handle the increasing number of wireless standards that preferably should run on the same hardware platform. To be able to perform this task it is crucial to understand both sides of the table, i.e., both algorithms and concepts for wireless communication as well as the implications arising on the hardware architecture. It is easier to handle the high complexity by separating those disciplines in a way of layered abstraction. However, this representation is imperfect, since many interconnected "details" belonging to different layers are lost in the attempt of handling the complexity. This results in poor implementations and the design of mobile terminals is no exception. Wireless communication standards are often designed based on mathematical algorithms with theoretical boundaries, with few considerations to actual implementation constraints such as, energy consumption, silicon area, etc. This thesis does not try to remove the layer abstraction model, given its undeniable advantages, but rather uses those cross-layer "details" that went missing during the abstraction. This is done in three manners: In the first part, the cross-layer optimization is carried out from the algorithm perspective. Important circuit design parameters, such as quantization are taken into consideration when designing the algorithm for OFDM symbol timing, CFO, and SNR estimation with a single bit, namely, the Sign-Bit. Proof-of-concept circuits were fabricated and showed high potential for low-end receivers. In the second part, the cross-layer optimization is accomplished from the opposite side, i.e., the hardware-architectural side. A SDR architecture is known for its flexibility and scalability over many applications. In this work a filtering application is mapped into software instructions in the SDR architecture in order to make filtering-specific modules redundant, and thus, save silicon area. In the third and last part, the optimization is done from an intermediate point within the algorithm-architecture spectrum. Here, a heterogeneous architecture with a combination of highly efficient and highly flexible modules is used to accomplish initial synchronization in at least two concurrent OFDM standards. A demonstrator was build capable of performing synchronization in any two standards, including LTE, WiFi, and DVB-H

State of the art baseband DSP platforms for Software Defined Radio: A survey

Software Defined Radio (SDR) is an innovative approach which is becoming a more and more promising technology for future mobile handsets. Several proposals in the field of embedded systems have been introduced by different universities and industries to support SDR applications. This article presents an overview of current platforms and analyzes the related architectural choices, the current issues in SDR, as well as potential future trends.Peer reviewe

A Reconfigurable Outer Modem Platform for Future Communications Systems

Future mobile and wireless communications networks require flexible modem architectures with high performance. Efficient utilization of application specific flexibility is key to fulfill these requirements. For high throughput a single processor can not provide the necessary computational power. Hence multi-processor architectures become necessary. This paper presents a multi-processor platform based on a new dynamically reconfigurable application specific instruction set processor (dr-ASIP) for the application domain of channel decoding. Inherently parallel decoding tasks can be mapped onto individual processing nodes. The implied challenging inter-processor communication is efficiently handled by a Network-on-Chip (NoC) such that the throughput of each node is not degraded. The dr-ASIP features Viterbi and Log-MAP decoding for support of convolutional and turbo codes of more than 10 currently specified mobile and wireless standards. Furthermore, its flexibility allows for adaptation to future systems

Multi-core Architectures and Streaming Applications

In this paper we focus on algorithms and reconfigurable multi-core architectures for streaming digital signal processing (DSP) applications. The multi-core concept has a number of advantages: (1) depending on the requirements more or fewer cores can be switched on/off, (2) the multi-core structure fits well to future process technologies, more cores will be available in advanced process technologies, but the complexity per core does not increase, (3) the multi-core concept is fault tolerant, faulty cores can be discarded and (4) multiple cores can be configured fast in parallel. Because in our approach processing and memory are combined in the cores, tasks can be executed efficiently on cores (locality of reference). There are a number of application domains that can be considered as streaming DSP applications: for example wireless baseband processing (for HiperLAN/2, WiMax, DAB, DRM, and DVB), multimedia processing (e.g. MPEG, MP3 coding/decoding), medical image processing, colour image processing, sensor processing (e.g. remote surveillance cameras) and phased array radar systems. In this paper the key characteristics of streaming DSP applications are highlighted, and the characteristics of the processing architectures to efficiently support these types of applications are addressed. We present the initial results of the Annabelle chip that we designed with our approach