Bandwidth optimization in asynchronous NoCs by customizing link wire length

Journal ArticleThe bandwidth requirement for each link on a network-on-chip (NoC) may differ based on topology and traffic properties of the IP cores. Available bandwidth on an asynchronous NoC link will also vary depending on the wire length between sender and receiver. We explore the benefit to NoC performance when this property is used to increase bandwidth on specific links that carry the most traffic of an SoC design. Two methods are used to accomplish this: specifying router locations on the floorplan, and adding pipeline latches on long links. Energy and latency characteristics of an asynchronous NoC are compared to a similarly-designed synchronous NoC. The results indicate that the asynchronous network has lower energy, and link-specific bandwidth optimization has improved the average packet latency. Adding pipeline latches to congested links yields the most improvement. This link-specific optimization is applicable not only to the router and network we present here, but any asynchronous NoC used in a eterogeneous SoC

Spatial parallelism in the routers of asynchronous on-chip networks

State-of-the-art multi-processor systems-on-chip use on-chip networks as their communication fabric. Although most on-chip networks are implemented synchronously, asynchronous on-chip networks have several advantages over their synchronous counterparts. Timing division multiplexing (TDM) flow control methods have been utilized in asynchronous on-chip networks extensively. The synchronization required by TDM leads to significant speed penalties. Compared with using TDM methods, spatial parallelism methods, such as the spatial division multiplexing (SDM) flow control method, achieve better network throughput with less area overhead.This thesis proposes several techniques to increase spatial parallelism in the routers of asynchronous on-chip networks.Channel slicing is a new pipeline structure that alleviates the speed penalty by removing the synchronization among bit-level data pipelines. It is also found out that the lookahead pipeline using early evaluated acknowledgement can be used in routers to further improve speed.SDM is a new flow control method proposed for asynchronous on-chip networks. It improves network throughput without introducing synchronization among buffers of different frames, which is required by TDM methods. It is also found that the area overhead of SDM is smaller than the virtual channel (VC) flow control method -- the most used TDM method. The major design problem of SDM is the area consuming crossbars. A novel 2-stage Clos switch structure is proposed to replace the crossbar in SDM routers, which significantly reduces the area overhead. This Clos switch is dynamically reconfigured by a new asynchronous Clos scheduler.Several asynchronous SDM routers are implemented using these new techniques. An asynchronous VC router is also reproduced for comparison. Performance analyses show that the SDM routers outperform the VC router in throughput, area overhead and energy efficiency.EThOS - Electronic Theses Online ServiceGBUnited Kingdo

Spatial parallelism in the routers of asynchronous on-chip networks

State-of-the-art multi-processor systems-on-chip use on-chip networks as their communication fabric. Although most on-chip networks are implemented synchronously, asynchronous on-chip networks have several advantages over their synchronous counterparts. Timing division multiplexing (TDM) flow control methods have been utilized in asynchronous on-chip networks extensively. The synchronization required by TDM leads to significant speed penalties. Compared with using TDM methods, spatial parallelism methods, such as the spatial division multiplexing (SDM) flow control method, achieve better network throughput with less area overhead.This thesis proposes several techniques to increase spatial parallelism in the routers of asynchronous on-chip networks.Channel slicing is a new pipeline structure that alleviates the speed penalty by removing the synchronization among bit-level data pipelines. It is also found out that the lookahead pipeline using early evaluated acknowledgement can be used in routers to further improve speed.SDM is a new flow control method proposed for asynchronous on-chip networks. It improves network throughput without introducing synchronization among buffers of different frames, which is required by TDM methods. It is also found that the area overhead of SDM is smaller than the virtual channel (VC) flow control method -- the most used TDM method. The major design problem of SDM is the area consuming crossbars. A novel 2-stage Clos switch structure is proposed to replace the crossbar in SDM routers, which significantly reduces the area overhead. This Clos switch is dynamically reconfigured by a new asynchronous Clos scheduler.Several asynchronous SDM routers are implemented using these new techniques. An asynchronous VC router is also reproduced for comparison. Performance analyses show that the SDM routers outperform the VC router in throughput, area overhead and energy efficiency.EThOS - Electronic Theses Online ServiceGBUnited Kingdo

Quarc: an architecture for efficient on-chip communication

The exponential downscaling of the feature size has enforced a paradigm shift from computation-based design to communication-based design in system on chip development. Buses, the traditional communication architecture in systems on chip, are incapable of addressing the increasing bandwidth requirements of future large systems. Networks on chip have emerged as an interconnection architecture offering unique solutions to the technological and design issues related to communication in future systems on chip. The transition from buses as a shared medium to networks on chip as a segmented medium has given rise to new challenges in system on chip realm. By leveraging the shared nature of the communication medium, buses have been highly efficient in delivering multicast communication. The segmented nature of networks, however, inhibits the multicast messages to be delivered as efficiently by networks on chip. Relying on extensive research on multicast communication in parallel computers, several network on chip architectures have offered mechanisms to perform the operation, while conforming to resource constraints of the network on chip paradigm. Multicast communication in majority of these networks on chip is implemented by establishing a connection between source and all multicast destinations before the message transmission commences. Establishing the connections incurs an overhead and, therefore, is not desirable; in particular in latency sensitive services such as cache coherence. To address high performance multicast communication, this research presents Quarc, a novel network on chip architecture. The Quarc architecture targets an area-efficient, low power, high performance implementation. The thesis covers a detailed representation of the building blocks of the architecture, including topology, router and network interface. The cost and performance comparison of the Quarc architecture against other network on chip architectures reveals that the Quarc architecture is a highly efficient architecture. Moreover, the thesis introduces novel performance models of complex traffic patterns, including multicast and quality of service-aware communication

An Energy-Efficient Reconfigurable Circuit Switched Network-on-Chip

Network-on-Chip (NoC) is an energy-efficient on-chip communication architecture for multi-tile System-on-Chip (SoC) architectures. The SoC architecture, including its run-time software, can replace inflexible ASICs for future ambient systems. These ambient systems have to be flexible as well as energy-efficient. To find an energy-efficient solution for the communication network we analyze three wireless applications. Based on their communication requirements we observe that revisiting of the circuit switching techniques is beneficial. In this paper we propose a new energy-efficient reconfigurable circuit-switched Network-on-Chip. By physically separating the concurrent data streams we reduce the overall energy consumption. The circuit-switched router has been synthesized and analyzed for its power consumption in 0.13 ¿m technology. A 5-port circuit-switched router has an area of 0.05 mm2 and runs at 1075 MHz. The proposed architecture consumes 3.5 times less energy compared to its packet-switched equivalen

NoC Design Flow for TDMA and QoS Management in a GALS Context

International audienceThis paper proposes a new approach dealing with the tedious problem of NoC guaranteed traffics according to GALS constraints impelled by the upcoming large System-on-Chips with multiclock domains. Our solution has been designed to adjust a tradeoff between synchronous and clockless asynchronous techniques. By means of smart interfaces between synchronous sub-NoCs, Quality-of-Service (QoS) for guaranteed traffic is assured over the entire chip despite clock heterogeneity. This methodology can be easily integrated in the usual NoC design flow as an extension to traditional NoC synchronous design flows. We present real implementation obtained with our tool for a 4G telecom scheme

A Scalable and Adaptive Network on Chip for Many-Core Architectures

In this work, a scalable network on chip (NoC) for future many-core architectures is proposed and investigated. It supports different QoS mechanisms to ensure predictable communication. Self-optimization is introduced to adapt the energy footprint and the performance of the network to the communication requirements. A fault tolerance concept allows to deal with permanent errors. Moreover, a template-based automated evaluation and design methodology and a synthesis flow for NoCs is introduced

Design and performance optimization of asynchronous networks-on-chip

As digital systems continue to grow in complexity, the design of conventional synchronous systems is facing unprecedented challenges. The number of transistors on individual chips is already in the multi-billion range, and a greatly increasing number of components are being integrated onto a single chip. As a consequence, modern digital designs are under strong time-to-market pressure, and there is a critical need for composable design approaches for large complex systems. In the past two decades, networks-on-chip (NoC’s) have been a highly active research area. In a NoC-based system, functional blocks are first designed individually and may run at different clock rates. These modules are then connected through a structured network for on-chip global communication. However, due to the rigidity of centrally-clocked NoC’s, there have been bottlenecks of system scalability, energy and performance, which cannot be easily solved with synchronous approaches. As a result, there has been significant recent interest in combing the notion of asynchrony with NoC designs. Since the NoC approach inherently separates the communication infrastructure, and its timing, from computational elements, it is a natural match for an asynchronous paradigm. Asynchronous NoC’s, therefore, enable a modular and extensible system composition for an ‘object-orient’ design style. The thesis aims to significantly advance the state-of-art and viability of asynchronous and globally-asynchronous locally-synchronous (GALS) networks-on-chip, to enable high-performance and low-energy systems. The proposed asynchronous NoC’s are nearly entirely based on standard cells, which eases their integration into industrial design flows. The contributions are instantiated in three different directions. First, practical acceleration techniques are proposed for optimizing the system latency, in order to break through the latency bottleneck in the memory interfaces of many on-chip parallel processors. Novel asynchronous network protocols are proposed, along with concrete NoC designs. A new concept, called ‘monitoring network’, is introduced. Monitoring networks are lightweight shadow networks used for fast-forwarding anticipated traffic information, ahead of the actual packet traffic. The routers are therefore allowed to initiate and perform arbitration and channel allocation in advance. The technique is successfully applied to two topologies which belong to two different categories – a variant mesh-of-trees (MoT) structure and a 2D-mesh topology. Considerable and stable latency improvements are observed across a wide range of traffic patterns, along with moderate throughput gains. Second, for the first time, a high-performance and low-power asynchronous NoC router is compared directly to a leading commercial synchronous counterpart in an advanced industrial technology. The asynchronous router design shows significant performance improvements, as well as area and power savings. The proposed asynchronous router integrates several advanced techniques, including a low-latency circular FIFO for buffer design, and a novel end-to-end credit-based virtual channel (VC) flow control. In addition, a semi-automated design flow is created, which uses portions of a standard synchronous tool flow. Finally, a high-performance multi-resource asynchronous arbiter design is developed. This small but important component can be directly used in existing asynchronous NoC’s for performance optimization. In addition, this standalone design promises use in opening up new NoC directions, as well as for general use in parallel systems. In the proposed arbiter design, the allocation of a resource to a client is divided into several steps. Multiple successive client-resource pairs can be selected rapidly in pipelined sequence, and the completion of the assignments can overlap in parallel. In sum, the thesis provides a set of advanced design solutions for performance optimization of asynchronous and GALS networks-on-chip. These solutions are at different levels, from network protocols, down to router- and component-level optimizations, which can be directly applied to existing basic asynchronous NoC designs to provide a leap in performance improvement