Multipacket reception in LTE femtocell networks

Dissertação apresentada para obtenção do Grau de Mestre em Engenharia Electrotécnica e de ComputadoresDriven by the growing demand for high-speed broadband wireless services, LTE technology has emerged and evolve, promising high data rates to the demanding mobile users. Based on the 3rd Generation Partnership Project (3GPP) speci cations,Long Term Evo- lution Advanced (LTE-A) telecommunication services predict the existence of macro base stations, Enhanced Node B (eNB) and micro stations HeNB with low power that complements the network's coverage. This dissertation studies the complementary use of HeNBs (femtocells 3GPP terminology) to provide broadband services. It is essential to maintain the networks performance with the network densi cation phenomenon, which brings signi cant interference problems and consequently more collisions and lost packets. The use of SC-FDE in the downlink of a LTE-A femtocell network - speci cally multipacket reception (MPR), with an IB-DFE receiver employing Multipacket Detection (MPD) and SIC techniques is proposed. A new telecommunications concept named GC emerged with the increasing environmental concerns. This dissertation shows the performance results of an iterative MPR and proposes a green association algorithm to change the network layout according to the mobile users demands reducing the Base Station (BS)'s negative contribution to the network total energy consumption. The overall results show that the technologies employed are a solution to achieve a favorable trade-o between performance and Energy E ciency (EE), responding to the global demands (high data rates) and concerns (low energy consumption and carbon footprint reduction). Keywords: Long Term Evolution(LTE), Single Carrier with Frequency Domain Equalization (SC-FDE), Iterative Block-Decision Feedback Equalizer (IB-DFE), Home enhanced Node B (HeNB), Successive Interference Cancellation(SIC),Multipacket Reception(MPR), Green Communications (GC)FCT/MEC Femtocells(PTDC/EEATEL/120666/2010), OPPORTUNISTIC CR(PTDC/EEA-TEL/115981/2009) and ADIN(PTDC/EEI-TEL/2990/2012) project

INTERFERENCE MANAGEMENT IN LTE SYSTEM AND BEYOUND

The key challenges to high throughput in cellular wireless communication system are interference, mobility and bandwidth limitation. Mobility has never been a problem until recently, bandwidth has been constantly improved upon through the evolutions in cellular wireless communication system but interference has been a constant limitation to any improvement that may have resulted from such evolution. The fundamental challenge to a system designer or a researcher is how to achieve high data rate in motion (high speed) in a cellular system that is intrinsically interference-limited. Multi-antenna is the solution to data on the move and the capacity of multi-antenna system has been demonstrated to increase proportionally with increase in the number of antennas at both transmitter and receiver for point-to-point communications and multi-user environment. However, the capacity gain in both uplink and downlink is limited in a multi-user environment like cellular system by interference, the number of antennas at the base station, complexity and space constraint particularly for a mobile terminal. This challenge in the downlink provided the motivation to investigate successive interference cancellation (SIC) as an interference management tool LTE system and beyond. The Simulation revealed that ordered successive interference (OSIC) out performs non-ordered successive interference cancellation (NSIC) and the additional complexity is justified based on the associated gain in BER performance of OSIC. The major drawback of OSIC is that it is not efficient in network environment employing power control or power allocation. Additional interference management techniques will be required to fully manage the interference.fi=Opinnäytetyö kokotekstinä PDF-muodossa.|en=Thesis fulltext in PDF format.|sv=Lärdomsprov tillgängligt som fulltext i PDF-format

Técnicas de equalização híbridas para sistemas heterogéneos na banda das ondas milimétricas

With the constant demand for better service and higher transmission rates current technologies are reaching the limits of the channel capacity. Although, technologies such as MIMO and Heterogeneous systems appear to increase the channel capacity by introducing more antennas at the transceivers making the link between users and base station more reliable. Furthermore, the current spectrum, sub-6GHz, is becoming saturated and due to the properties of such frequencies the deployment of heterogeneous systems can introduce some levels of interference. Towards improving future communication systems a new part of the frequencies spectrum available should be used, researchers have their eyes on the mmWave band. This band allows to increase the carrier frequency and respective signal bandwidth and therefore increase the transmission speeds, moreover the properties of such frequencies unlock some advantages over the frequencies used in the sub-6G band. Additionally, mmWave band can be combined with massive MIMO technology to enhance the system capacity and to deploy more antenna elements in the transceivers. One more key technology that improves the energy efficiency in systems with hundreds of antenna elements is the possibility to combine analog and digital precoding techniques denoted as hybrid architectures. The main advantages of such techniques is that contrary to the full digital precoding processing used in current systems this new architecture allows to reduce the number of RF chains per antenna leading to improved energy efficiency. Furthermore to handle heterogeneous systems that have small-cells within the macro-cell, techniques such as Interference Alignment (IA) can be used to efficiently remove the existing multi-tier interference. In this dissertation a massive MIMO mmWave heterogeneous system is implemented and evaluated. It is designed analog-digital equalizers to efficiently remove both the intra an inter-tier interference. At digital level, an interference alignment technique is used to remove the interference and increase the spectral efficiency. The results showed that the proposed solutions are efficient to remove the macro and small cells interference.Com a constante procura de melhores serviços e taxas de transmissão mais elevadas, as tecnologias atuais estão a atingir os limites de capacidade do canal. Contudo tecnologias como o MIMO e os sistemas heterogéneos permitem aumentar a capacidade do canal através da introdução de mais antenas nos transcetores e através da implementação de pequenos pontos de acesso espalhados pela célula primária, com o intuito de tornar as ligações entre os utilizadores e a estação base mais fiáveis. Tendo também em atenção que o espectro atual, sub-6GHz, está sobrecarregado e que devido às propriedades das frequências utilizadas a implementação de sistemas heterogéneos pode levar a níveis de interferência insustentáveis. Por modo a resolver esta sobrecarga futuros sistemas de comunicação devem aproveitar uma maior parte do espectro de frequências disponível. A banda das ondas milimétricas (mmWave) tem sido apontada como solução, o que permite aumentar a frequência utilizada para transportar o sinal e consequentemente aumentar as velocidades de transmissão. Uma outra vantagem da banda mmWave é que pode ser combinada com a tecnologia MIMO massivo, permitindo implementar mais elementos de antena nos terminais e consequentemente aumentar a capacidade do sistema. Umas das tecnologias desenvolvida para melhorar a eficiência energética em sistemas com centenas de antenas é a possibilidade de combinar técnicas de codificação analógica e digital, designadas como arquiteturas híbridas. A principal vantagem desta técnica é que, contrariamente ao processamento feito nos sistemas atuais, totalmente no domínio digital, esta nova arquitetura permite reduzir o número de cadeias RF por antena. Com o intuito de reduzir a interferência em sistemas heterogéneos, técnicas como o alinhamento de interferência são usadas para separar utilizadores das células secundárias dos utilizadores das células primárias de modo a reduzir a interferência multi-nível existente no sistema geral. Nesta dissertação, é implementado e avaliado um sistema heterogéneo que combina MIMO massivo e ondas milimétricas. Este sistema é projetado com equalizadores analógico-digitais para remover com eficiência a interferência intra e inter-camadas. No domínio digital é utilizada a técnica de alinhamento de interferência para remover a interferência e aumentar a eficiência espectral. Os resultados mostram que as soluções propostas são eficientes para remover a interferência entre as células secundárias e a primária.Mestrado em Engenharia Eletrónica e Telecomunicaçõe

Channel estimation in massive MIMO systems

Last years were characterized by a great demand for high data throughput, good quality and spectral efficiency in wireless communication systems. Consequently, a revolution in cellular networks has been set in motion towards to 5G. Massive multiple-input multiple-output (MIMO) is one of the new concepts in 5G and the idea is to scale up the known MIMO systems in unprecedented proportions, by deploying hundreds of antennas at base stations. Although, perfect channel knowledge is crucial in these systems for user and data stream separation in order to cancel interference. The most common way to estimate the channel is based on pilots. However, problems such as interference and pilot contamination (PC) can arise due to the multiplicity of channels in the wireless link. Therefore, it is crucial to define techniques for channel estimation that together with pilot contamination mitigation allow best system performance and at same time low complexity. This work introduces a low-complexity channel estimation technique based on Zadoff-Chu training sequences. In addition, different approaches were studied towards pilot contamination mitigation and low complexity schemes, with resort to iterative channel estimation methods, semi-blind subspace tracking techniques and matrix inversion substitutes. System performance simulations were performed for the several proposed techniques in order to identify the best tradeoff between complexity, spectral efficiency and system performance

Vandermonde-subspace Frequency Division Multiplexing for Two-Tiered Cognitive Radio Networks

Vandermonde-subspace frequency division multiplexing (VFDM) is an overlay spectrum sharing technique for cognitive radio. VFDM makes use of a precoder based on a Vandermonde structure to transmit information over a secondary system, while keeping an orthogonal frequency division multiplexing (OFDM)-based primary system interference-free. To do so, VFDM exploits frequency selectivity and the use of cyclic prefixes by the primary system. Herein, a global view of VFDM is presented, including also practical aspects such as linear receivers and the impact of channel estimation. We show that VFDM provides a spectral efficiency increase of up to 1 bps/Hz over cognitive radio systems based on unused band detection. We also present some key design parameters for its future implementation and a feasible channel estimation protocol. Finally we show that, even when some of the theoretical assumptions are relaxed, VFDM provides non-negligible rates while protecting the primary system.Comment: 9 pages, accepted for publication in IEEE Transactions on Communication

LTE Advanced: Technology and Performance Analysis

Wireless data usage is increasing at a phenomenal rate and driving the need for continued innovations in wireless data technologies to provide more capacity and higher quality of service. In October 2009, 3rd Generation Partnership Project (3GPP) submitted LTE-Advanced to the ITU as a proposed candidate IMT-Advanced technology for which specifications could become available in 2011 through Release-10 . The aim of “LTE-Advanced” is to further enhance LTE radio access in terms of system performance and capabilities compared to current cellular systems, including the first release of LTE, with a specific goal to ensure that LTE fulfills and even surpass the requirements of “IMT-Advanced” as defined by the International Telecommunication Union (ITU-R) . This thesis offers an introduction to the mobile communication standard known as LTE Advanced, depicting the evolution of the standard from its roots and discussing several important technologies that help it evolve to accomplishing the IMT-Advanced requirements. A short history of the LTE standard is offered, along with a discussion of its standards and performance. LTE-Advanced details include analysis on the physical layer by investigating the performance of SC-FDMA and OFDMA of LTE physical layer. The investigation is done by considering different modulation schemes (QPSK, 16QAM and 64QAM) on the basis of PAPR, BER, power spectral density (PSD) and error probability by simulating the model of SC-FDMA & OFDMA. To evaluate the performance in presence of noise, an Additive White Gaussian Noise (AWGN) channel was introduced. A set of conclusions is derived from our results describing the effect of higher order modulation schemes on BER and error probability for both OFDMA and SC-FDMA. The power spectral densities of both the multiple access techniques (OFDMA and SC-FDMA) are calculated and result shows that the OFDMA has higher power spectral density.fi=Opinnäytetyö kokotekstinä PDF-muodossa.|en=Thesis fulltext in PDF format.|sv=Lärdomsprov tillgängligt som fulltext i PDF-format

Modeling and Optimization of Next-Generation Wireless Access Networks

The ultimate goal of the next generation access networks is to provide all network users, whether they are fixed or mobile, indoor or outdoor, with high data rate connectivity, while ensuring a high quality of service. In order to realize this ambitious goal, delay, jitter, error rate and packet loss should be minimized: a goal that can only be achieved through integrating different technologies, including passive optical networks, 4th generation wireless networks, and femtocells, among others. This thesis focuses on medium access control and physical layers of future networks. In this regard, the first part of this thesis discusses techniques to improve the end-to-end quality of service in hybrid optical-wireless networks. In these hybrid networks, users are connected to a wireless base station that relays their data to the core network through an optical connection. Hence, by integrating wireless and optical parts of these networks, a smart scheduler can predict the incoming traffic to the optical network. The prediction data generated herein is then used to propose a traffic-aware dynamic bandwidth assignment algorithm for reducing the end-to-end delay. The second part of this thesis addresses the challenging problem of interference management in a two-tier macrocell/femtocell network. A high quality, high speed connection for indoor users is ensured only if the network has a high signal to noise ratio. A requirement that can be fulfilled with using femtocells in cellular networks. However, since femtocells generate harmful interference to macrocell users in proximity of them, careful analysis and realistic models should be developed to manage the introduced interference. Thus, a realistic model for femtocell interference outside suburban houses is proposed and several performance measures, e.g., signal to interference and noise ratio and outage probability are derived mathematically for further analysis. The quality of service of cellular networks can be degraded by several factors. For example, in industrial environments, simultaneous fading and strong impulsive noise significantly deteriorate the error rate performance. In the third part of this thesis, a technique to improve the bit error rate of orthogonal frequency division multiplexing systems in industrial environments is presented. This system is the most widely used technology in next-generation networks, and is very susceptible to impulsive noise, especially in fading channels. Mathematical analysis proves that the proposed method can effectively mitigate the degradation caused by impulsive noise and significantly improve signal to interference and noise ratio and bit error rate, even in frequency-selective fading channels

Physical Layer Techniques for High Frequency Wireline Broadband Systems

This thesis collects contributions to wireline and wireless communication systems with an emphasis on multiuser and multicarrier physical layer technology. To deliver increased capacity, modern wireline access systems such as G.fast extend the signal bandwidth up from tens to hundreds of MHz. This ambitious development revealed a number of unforeseen hurdles such as the impact of impedance changes in various forms. Impedance changes have a strong effect on the performance of multi-user crosstalk mitigation techniques such as vectoring. The first part of the thesis presents papers covering the identification of one of these problems, a model describing why it occurs and a method to mitigate its effects, improving line stability for G.fast systems.A second part of the thesis deals with the effects of temperature changes on wireline channels. When a vectored (MIMO) wireline system is initialized, channel estimates need to be obtained. This thesis presents contributions on the feasibility of re-using channel coefficients to speed up the vectoring startup procedures, even after the correct coefficients have changed, e.g., due to temperature changes. We also present extensive measurement results showing the effects of temperature changes on copper channels using a temperature chamber and British cables. The last part of the thesis presents three papers on the convergence of physical layer technologies, more specifically the deployment of OFDM-based radio systems using twisted pairs in different ways. In one proposed scenario, the idea of using the access copper lines to deploy small cells inside users' homes is explored. The feasibility of the concept, the design of radio-heads and a practical scheme for crosstalk mitigation are presented in three contributions

D13.2 Techniques and performance analysis on energy- and bandwidth-efficient communications and networking

Deliverable D13.2 del projecte europeu NEWCOM#The report presents the status of the research work of the various Joint Research Activities (JRA) in WP1.3 and the results that were developed up to the second year of the project. For each activity there is a description, an illustration of the adherence to and relevance with the identified fundamental open issues, a short presentation of the main results, and a roadmap for the future joint research. In the Annex, for each JRA, the main technical details on specific scientific activities are described in detail.Peer ReviewedPostprint (published version

Performance of MIMO Schemes in Radio-over-fibre-based Distributed Antenna System

The research presented in this thesis has focused on the use of MIMO wireless communications in a RoF-based DAS to improve wireless coverage and capacity performance in an indoor environment. The aim is to analyse the practical issues that cause throughput to deteriorate when commercial MIMO APs are used in a RoF-DAS, and also to verify that improved performance - lower error rates and higher capacities - can be achieved by a large physical separation between the RAUs when specific multi-antenna scheme algorithms are used. The performance of an IEEE 802.11n MIMO-supported AP and IEEE 802.11g spatial-diversity-supported AP are investigated in a RoF-DAS when different fibre lengths are connecting the AP in the central unit to the RAUs, and when the RAUs are widely separated. The analysis indicates that for MIMO, the throughput drops rapidly due to severe ISI caused by differential delay when the fibre-length difference exceeds a certain distance, while for spatial diversity high throughputs can be maintained even at large fibre-length difference. Further, it was observed that largely separated RAU may lead to power imbalances and the throughput drops in specific wireless user's positions when the received power imbalance was above 12-15dB for MIMO-supported AP, while for spatial-diversity-supported AP the power imbalance does not affect the throughput. The majority of previous works on RoF-DAS for improving MIMO systems were based on commercial products and the specific algorithms used within these products are unknown. An investigation was carried out at microwave frequency with SIMO algorithms in RoF-DAS uplink, MISO and MIMO algorithms in RoF-DAS downlink, and compared with the performance of a SISO system. This investigation was later extended to millimetre-wave frequency where larger bands of frequency are available enabling the possibility of wider bandwidth and higher data rates. The result shows significantly reduced error rate and modestly increased capacity for a wireless 1x2 SIMO uplink using MRC algorithm and 2x1 MISO downlink using Alamouti STBC algorithm. Also, error rate was reduced for a wireless 2x2 MIMO downlink using the zero-forcing algorithm while, most importantly, greatly increased capacity was achieved through the spatial multiplexing gain